ehci: Add support for Qualcomm EHCI

This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>

doc/device-tree-bindings/usb/ehci-msm.txt

@@ -0,0 +1,10 @@
+Chipidea EHCI controller (part of OTG controller) used on Qualcomm devices.
+
+Required properties:
+- compatible: must be "qcom,ehci-host"
+- reg: start address and size of the registers
+
+ehci@78d9000 {
+	compatible = "qcom,ehci-host";
+	reg = <0x78d9000 0x400>;
+};

drivers/usb/host/Kconfig

@@ -74,6 +74,17 @@ config USB_EHCI_MX6
 	---help---
 	  Enables support for the on-chip EHCI controller on i.MX6 SoCs.
 
+config USB_EHCI_MSM
+	bool "Support for Qualcomm on-chip EHCI USB controller"
+	depends on DM_USB
+	select USB_ULPI_VIEWPORT
+	default n
+	---help---
+	  Enables support for the on-chip EHCI controller on Qualcomm
+	  Snapdragon SoCs.
+	  This driver supports combination of Chipidea USB controller
+	  and Synapsys USB PHY in host mode only.
+
 config USB_EHCI_GENERIC
 	bool "Support for generic EHCI USB controller"
 	depends on OF_CONTROL

drivers/usb/host/Makefile

@@ -43,6 +43,7 @@ obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx6.o
 obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
 obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o
+obj-$(CONFIG_USB_EHCI_MSM) += ehci-msm.o
 obj-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
 obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o
 obj-$(CONFIG_USB_EHCI_SUNXI) += ehci-sunxi.o

drivers/usb/host/ehci-msm.c

@@ -0,0 +1,178 @@
+/*
+ * Qualcomm EHCI driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
+ *
+ * Based on Linux driver
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <libfdt.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+#include <usb/ulpi.h>
+#include <wait_bit.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <linux/compat.h>
+#include "ehci.h"
+
+/* PHY viewport regs */
+#define ULPI_MISC_A_READ         0x96
+#define ULPI_MISC_A_SET          0x97
+#define ULPI_MISC_A_CLEAR        0x98
+#define ULPI_MISC_A_VBUSVLDEXTSEL    (1 << 1)
+#define ULPI_MISC_A_VBUSVLDEXT       (1 << 0)
+
+#define GEN2_SESS_VLD_CTRL_EN (1 << 7)
+
+#define SESS_VLD_CTRL         (1 << 25)
+
+struct msm_ehci_priv {
+	struct ehci_ctrl ctrl; /* Needed by EHCI */
+	struct usb_ehci *ehci; /* Start of IP core*/
+	struct ulpi_viewport ulpi_vp; /* ULPI Viewport */
+};
+
+int __weak board_prepare_usb(enum usb_init_type type)
+{
+	return 0;
+}
+
+static void setup_usb_phy(struct msm_ehci_priv *priv)
+{
+	/* Select and enable external configuration with USB PHY */
+	ulpi_write(&priv->ulpi_vp, (u8 *)ULPI_MISC_A_SET,
+		   ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static void reset_usb_phy(struct msm_ehci_priv *priv)
+{
+	/* Disable VBUS mimicing in the controller. */
+	ulpi_write(&priv->ulpi_vp, (u8 *)ULPI_MISC_A_CLEAR,
+		   ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
+}
+
+
+static int msm_init_after_reset(struct ehci_ctrl *dev)
+{
+	struct msm_ehci_priv *p = container_of(dev, struct msm_ehci_priv, ctrl);
+	struct usb_ehci *ehci = p->ehci;
+
+	/* select ULPI phy */
+	writel(PORT_PTS_ULPI, &ehci->portsc);
+	setup_usb_phy(p);
+
+	/* Enable sess_vld */
+	setbits_le32(&ehci->genconfig2, GEN2_SESS_VLD_CTRL_EN);
+
+	/* Enable external vbus configuration in the LINK */
+	setbits_le32(&ehci->usbcmd, SESS_VLD_CTRL);
+
+	/* USB_OTG_HS_AHB_BURST */
+	writel(0x0, &ehci->sbuscfg);
+
+	/* USB_OTG_HS_AHB_MODE: HPROT_MODE */
+	/* Bus access related config. */
+	writel(0x08, &ehci->sbusmode);
+
+	/* set mode to host controller */
+	writel(CM_HOST, &ehci->usbmode);
+
+	return 0;
+}
+
+static const struct ehci_ops msm_ehci_ops = {
+	.init_after_reset = msm_init_after_reset
+};
+
+static int ehci_usb_probe(struct udevice *dev)
+{
+	struct msm_ehci_priv *p = dev_get_priv(dev);
+	struct usb_ehci *ehci = p->ehci;
+	struct ehci_hccr *hccr;
+	struct ehci_hcor *hcor;
+	int ret;
+
+	hccr = (struct ehci_hccr *)((phys_addr_t)&ehci->caplength);
+	hcor = (struct ehci_hcor *)((phys_addr_t)hccr +
+			HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
+
+	ret = board_prepare_usb(USB_INIT_HOST);
+	if (ret < 0)
+		return ret;
+
+	return ehci_register(dev, hccr, hcor, &msm_ehci_ops, 0, USB_INIT_HOST);
+}
+
+static int ehci_usb_remove(struct udevice *dev)
+{
+	struct msm_ehci_priv *p = dev_get_priv(dev);
+	struct usb_ehci *ehci = p->ehci;
+	int ret;
+
+	ret = ehci_deregister(dev);
+	if (ret)
+		return ret;
+
+	/* Stop controller. */
+	clrbits_le32(&ehci->usbcmd, CMD_RUN);
+
+	reset_usb_phy(p);
+
+	ret = board_prepare_usb(USB_INIT_DEVICE); /* Board specific hook */
+	if (ret < 0)
+		return ret;
+
+	/* Reset controller */
+	setbits_le32(&ehci->usbcmd, CMD_RESET);
+
+	/* Wait for reset */
+	if (wait_for_bit(__func__, &ehci->usbcmd, CMD_RESET, false, 30,
+			 false)) {
+		printf("Stuck on USB reset.\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int ehci_usb_ofdata_to_platdata(struct udevice *dev)
+{
+	struct msm_ehci_priv *priv = dev_get_priv(dev);
+
+	priv->ulpi_vp.port_num = 0;
+	priv->ehci = (void *)dev_get_addr(dev);
+
+	if (priv->ehci == (void *)FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	/* Warning: this will not work if viewport address is > 64 bit due to
+	 * ULPI design.
+	 */
+	priv->ulpi_vp.viewport_addr = (phys_addr_t)&priv->ehci->ulpi_viewpoint;
+
+	return 0;
+}
+
+static const struct udevice_id ehci_usb_ids[] = {
+	{ .compatible = "qcom,ehci-host", },
+	{ }
+};
+
+U_BOOT_DRIVER(usb_ehci) = {
+	.name	= "ehci_msm",
+	.id	= UCLASS_USB,
+	.of_match = ehci_usb_ids,
+	.ofdata_to_platdata = ehci_usb_ofdata_to_platdata,
+	.probe = ehci_usb_probe,
+	.remove = ehci_usb_remove,
+	.ops	= &ehci_usb_ops,
+	.priv_auto_alloc_size = sizeof(struct msm_ehci_priv),
+	.flags	= DM_FLAG_ALLOC_PRIV_DMA,
+};