Merge branch 'master' of git://git.denx.de/u-boot-samsung

arch/arm/cpu/armv7/exynos/Kconfig

@@ -24,6 +24,10 @@ config TARGET_TRATS2
 config TARGET_ODROID
 	bool "Exynos4412 Odroid board"
 
+config TARGET_ODROID_XU3
+	bool "Exynos5422 Odroid board"
+	select OF_CONTROL
+
 config TARGET_ARNDALE
 	bool "Exynos5250 Arndale board"
 	select CPU_V7_HAS_NONSEC

arch/arm/cpu/armv7/exynos/clock.c

@@ -848,6 +848,8 @@ static unsigned long exynos5420_get_mmc_clk(int dev_index)
 
 	if (sel == 0x3)
 		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x4)
+		sclk = get_pll_clk(SPLL);
 	else if (sel == 0x6)
 		sclk = get_pll_clk(EPLL);
 	else

arch/arm/dts/Makefile

@@ -13,7 +13,8 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5420-peach-pit.dtb \
-	exynos5800-peach-pi.dtb
+	exynos5800-peach-pi.dtb \
+	exynos5422-odroidxu3.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \

arch/arm/dts/exynos5422-odroidxu3.dts

@@ -0,0 +1,49 @@
+/*
+ * Odroid XU3 device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/dts-v1/;
+#include "exynos54xx.dtsi"
+
+/ {
+	model = "Odroid XU3 based on EXYNOS5422";
+	compatible = "samsung,odroidxu3", "samsung,exynos5";
+
+	aliases {
+		serial0 = "/serial@12C00000";
+		console = "/serial@12C20000";
+	};
+
+	memory {
+		device_type = "memory";
+		reg =  <0x40000000 0x10000000
+			0x50000000 0x10000000
+			0x60000000 0x10000000
+			0x70000000 0x10000000
+			0x80000000 0x10000000
+			0x90000000 0x10000000
+			0xa0000000 0x10000000
+			0xb0000000 0xea00000>;
+	};
+
+	ehci@12110000 {
+		samsung,vbus-gpio = <&gpio 0x66 0>; /* X26 */
+	};
+
+	serial@12C20000 {
+		status="okay";
+	};
+
+	mmc@12200000 {
+		fifoth_val = <0x201f0020>;
+	};
+
+	mmc@12220000 {
+		fifoth_val = <0x201f0020>;
+	};
+};

arch/arm/dts/exynos5800-peach-pi.dts

@@ -63,11 +63,6 @@
 	              reg = <0x20>;
 	              compatible = "maxim,max98090-codec";
 	       };
-
-	        edp-lvds-bridge@48 {
-	                compatible = "parade,ps8625";
-	                reg = <0x48>;
-	        };
 	};
 
         sound@3830000 {

arch/arm/include/asm/arch-exynos/system.h

@@ -41,7 +41,4 @@ void set_usbhost_mode(unsigned int mode);
 void set_system_display_ctrl(void);
 int exynos_lcd_early_init(const void *blob);
 
-/* Initialize the Parade dP<->LVDS bridge if present */
-int parade_init(const void *blob);
-
 #endif	/* _EXYNOS4_SYSTEM_H */

board/samsung/smdk5420/Kconfig

@@ -1,3 +1,16 @@
+if TARGET_ODROID_XU3
+
+config SYS_BOARD
+	default "smdk5420"
+
+config SYS_VENDOR
+	default "samsung"
+
+config SYS_CONFIG_NAME
+	default "odroid_xu3"
+
+endif
+
 if TARGET_PEACH_PI
 
 config SYS_BOARD

board/samsung/smdk5420/smdk5420.c

@@ -9,6 +9,7 @@
 #include <asm/io.h>
 #include <i2c.h>
 #include <lcd.h>
+#include <parade.h>
 #include <spi.h>
 #include <errno.h>
 #include <asm/gpio.h>
@@ -21,24 +22,8 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_USB_EHCI_EXYNOS
-static int board_usb_vbus_init(void)
-{
-	/* Enable VBUS power switch */
-	gpio_direction_output(EXYNOS5420_GPIO_X26, 1);
-
-	/* VBUS turn ON time */
-	mdelay(3);
-
-	return 0;
-}
-#endif
-
 int exynos_init(void)
 {
-#ifdef CONFIG_USB_EHCI_EXYNOS
-	board_usb_vbus_init();
-#endif
 	return 0;
 }
 

configs/odroid-xu3_defconfig

@@ -0,0 +1,4 @@
+CONFIG_ARM=y
+CONFIG_ARCH_EXYNOS=y
+CONFIG_TARGET_ODROID_XU3=y
+CONFIG_DEFAULT_DEVICE_TREE="exynos5422-odroidxu3"

doc/README.odroid

@@ -1,28 +1,39 @@
- U-boot for Odroid X2/U3
+ U-boot for Odroid X2/U3/XU3
 ========================
 
 1. Summary
 ==========
-This is a quick instruction for setup Odroid boards based on Exynos4412.
+This is a quick instruction for setup Odroid boards.
-Board config: odroid_config
+Board config: odroid_config for X2/U3
+Board config: odroid-xu3_config for XU3
 
 2. Supported devices
 ====================
-This U-BOOT config can be used on two boards:
+This U-BOOT config can be used on three boards:
 - Odroid U3
 - Odroid X2
 with CPU Exynos 4412 rev 2.0 and 2GB of RAM
+- Odroid XU3
+with CPU Exynos5422 and 2GB of RAM
 
 3. Boot sequence
 ================
 iROM->BL1->(BL2 + TrustZone)->U-BOOT
 
-This version of U-BOOT doesn't implement SPL but it is required(BL2)
+This version of U-BOOT doesn't implement SPL. So, BL1, BL2, and TrustZone
-and can be found in "boot.tar.gz" from here:
+binaries are needed to boot up.
+
+<< X2/U3 >>
+It can be found in "boot.tar.gz" from here:
 http://dev.odroid.com/projects/4412boot/wiki/FrontPage?action=download&value=boot.tar.gz
 or here:
 http://odroid.in/guides/ubuntu-lfs/boot.tar.gz
 
+<< XU3 >>
+It can be downloaded from:
+https://github.com/hardkernel/u-boot/tree/odroidxu3-v2012.07/sd_fuse/hardkernel
+
+
 4. Boot media layout
 ====================
 The table below shows SD/eMMC cards layout for U-boot.
@@ -35,18 +46,20 @@ The block offset is starting from 0 and the block size is 512B.
 | Bl2       | 31   | 30   |  1 (boot) |
 | U-boot    | 63   | 62   |  1 (boot) |
 | Tzsw      | 2111 | 2110 |  1 (boot) |
-| Uboot Env | 2500 | 2500 |  0 (user) |
+| Uboot Env | 2560 | 2560 |  0 (user) |
  -------------------------------------
 
 5. Prepare the SD boot card - with SD card reader
 =================================================
 To prepare bootable media you need boot binaries provided by hardkernel.
-File "boot.tar.gz" (link in point 3.) contains:
+From the downloaded files, You can find:
-- E4412_S.bl1.HardKernel.bin
+- bl1.bin
-- E4412_S.tzsw.signed.bin
+- tzsw.bin
-- bl2.signed.bin
+- bl2.bin
 - sd_fusing.sh
 - u-boot.bin
+(The file names can be slightly different, but you can distinguish what they are
+without problem)
 
 This is all you need to boot this board. But if you want to use your custom
 u-boot then you need to change u-boot.bin with your own u-boot binary*
@@ -56,7 +69,7 @@ and run the script "sd_fusing.sh" - this script is valid only for SD card.
 The proper binary file of current U-boot is u-boot-dtb.bin.
 
 quick steps for Linux:
-- extract boot.tar.gz
+- Download all files from the link at point 3 and extract it if needed.
 - put any SD card into the SD reader
 - check the device with "dmesg"
 - run ./sd_fusing.sh /dev/sdX - where X is SD card device (but not a partition)
@@ -66,7 +79,7 @@ Check if Hardkernel U-boot is booting, and next do the same with your U-boot.
    with a eMMC card reader (boot from eMMC card slot)
 =====================================================
 To boot the device from the eMMC slot you should use a special card reader
-which supports eMMC partiion switch. All of the boot binaries are stored
+which supports eMMC partition switch. All of the boot binaries are stored
 on the eMMC boot partition which is normally hidden.
 
 The "sd_fusing.sh" script can be used after updating offsets of binaries
@@ -81,8 +94,8 @@ But then the device can boot only from the SD card slot.
 
 8. Prepare the boot media using Hardkernel U-boot
 =================================================
-You can update the U-boot to the custom one if you have an working bootloader
+You can update the U-boot to the custom one if you have a working bootloader
-delivered with the board on a eMMC/SD card. Then follow the steps:
+delivered with the board on the eMMC/SD card. Then follow the steps:
 - install the android fastboot tool
 - connect a micro usb cable to the board
 - on the U-boot prompt, run command: fastboot (as a root)
@@ -91,7 +104,7 @@ delivered with the board on a eMMC/SD card. Then follow the steps:
 
 9. Partition layout
 ====================
-Default U-boot environment is setup for fixed partiion layout.
+Default U-boot environment is setup for fixed partition layout.
 
 Partition table: MSDOS. Disk layout and files as listed in the table below.
  ----- ------ ------ ------ -------- ---------------------------------
@@ -106,6 +119,7 @@ Partition table: MSDOS. Disk layout and files as listed in the table below.
 Supported fdt files are:
 - exynos4412-odroidx2.dtb
 - exynos4412-odroidu3.dtb
+- exynos5422-odroidxu3.dtb
 
 Supported kernel files are:
 - Image.itb
@@ -144,6 +158,7 @@ And the boot sequence is:
 
 11. USB host support
 ====================
+NOTE: This section is only for Odroid X2/U3.
 
 The ethernet can be accessed after starting the USB subsystem in U-Boot.
 The adapter does not come with a preconfigured MAC address, and hence it needs

include/configs/arndale.h

@@ -24,10 +24,6 @@
 #define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_EXYNOS
 
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-
 /* MMC SPL */
 #define CONFIG_EXYNOS_SPL
 

include/configs/exynos5-common.h

@@ -174,6 +174,16 @@
 
 #define CONFIG_CMD_GPIO
 
+/* USB */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS	2
+
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_SMSC95XX
+
 /* USB boot mode */
 #define CONFIG_USB_BOOTING
 #define EXYNOS_COPY_USB_FNPTR_ADDR	0x02020070

include/configs/exynos5250-common.h

@@ -22,11 +22,6 @@
 
 #define CONFIG_SPL_MAX_FOOTPRINT	(14 * 1024)
 
-/* USB */
-#define CONFIG_CMD_USB
-#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS	2
-#define CONFIG_USB_STORAGE
-
 #define CONFIG_SPL_TEXT_BASE	0x02023400
 
 #define CONFIG_IRAM_STACK	0x02050000

include/configs/exynos5420-common.h

@@ -13,13 +13,6 @@
 /* A variant of Exynos5420 (Exynos5 Family) */
 #define CONFIG_EXYNOS5800
 
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SPI_FLASH
-#define CONFIG_ENV_SPI_BASE	0x12D30000
-#define FLASH_SIZE		(0x4 << 20)
-#define CONFIG_ENV_OFFSET	(FLASH_SIZE - CONFIG_BL2_SIZE)
-#define CONFIG_SPI_BOOTING
-
 #include <configs/exynos5-common.h>
 
 #define CONFIG_ARCH_EARLY_INIT_R
@@ -29,8 +22,6 @@
 
 #define CONFIG_VAR_SIZE_SPL
 
-#define CONFIG_SYS_SDRAM_BASE		0x20000000
-#define CONFIG_SYS_TEXT_BASE		0x23E00000
 #ifdef CONFIG_VAR_SIZE_SPL
 #define CONFIG_SPL_TEXT_BASE		0x02024410
 #else
@@ -47,15 +38,4 @@
 
 #define CONFIG_BOARD_REV_GPIO_COUNT	2
 
-#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS	2
-
-/*
- * Put the initial stack pointer 1KB below this to allow room for the
- * SPL marker. This value is arbitrary, but gd_t is placed starting here.
- */
-#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_IRAM_TOP - 0x800)
-
-/* Miscellaneous configurable options */
-#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
-
 #endif	/* __CONFIG_EXYNOS5420_H */

include/configs/odroid_xu3.h

@@ -0,0 +1,55 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics
+ * Hyungwon Hwang <human.hwang@samsung.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __CONFIG_ODROID_XU3_H
+#define __CONFIG_ODROID_XU3_H
+
+#include "exynos5420-common.h"
+
+#define CONFIG_SYS_PROMPT		"ODROID-XU3 # "
+#define CONFIG_IDENT_STRING		" for ODROID-XU3"
+
+#define CONFIG_BOARD_COMMON
+
+#define CONFIG_SYS_SDRAM_BASE		0x40000000
+#define CONFIG_SYS_TEXT_BASE		0x43E00000
+
+/* select serial console configuration */
+#define CONFIG_SERIAL2			/* use SERIAL 2 */
+
+#define TZPC_BASE_OFFSET		0x10000
+
+#define CONFIG_CMD_MMC
+
+/*
+ * FIXME: The number of bank is actually 8. But there is no way to reserve the
+ * last 16 Mib in the last bank now. So I just excluded the last bank
+ * temporally.
+ */
+#define CONFIG_NR_DRAM_BANKS	7
+#define SDRAM_BANK_SIZE		(256UL << 20UL)	/* 256 MB */
+
+#define CONFIG_ENV_IS_IN_MMC
+
+#undef CONFIG_ENV_SIZE
+#undef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_SIZE			4096
+#define CONFIG_ENV_OFFSET		(SZ_1K * 1280) /* 1.25 MiB offset */
+
+#define CONFIG_SYS_INIT_SP_ADDR        (CONFIG_SYS_LOAD_ADDR - 0x1000000)
+
+#define CONFIG_DEFAULT_CONSOLE		"console=ttySAC2,115200n8\0"
+
+/* USB */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_EXYNOS
+
+/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */
+#undef CONFIG_EXYNOS_TMU
+#undef CONFIG_TMU_CMD_DTT
+
+#endif	/* __CONFIG_H */

include/configs/peach-pi.h

@@ -14,14 +14,20 @@
 #define CONFIG_ENV_SPI_BASE	0x12D30000
 #define FLASH_SIZE		(0x4 << 20)
 #define CONFIG_ENV_OFFSET	(FLASH_SIZE - CONFIG_BL2_SIZE)
+#define CONFIG_SPI_BOOTING
 
 #include <configs/exynos5420-common.h>
 #include <configs/exynos5-dt-common.h>
 
 #define CONFIG_BOARD_COMMON
 
+#define CONFIG_SYS_SDRAM_BASE	0x20000000
+#define CONFIG_SYS_TEXT_BASE	0x23E00000
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_IRAM_TOP - 0x800)
+
 /* select serial console configuration */
 #define CONFIG_SERIAL3		/* use SERIAL 3 */
+#define CONFIG_DEFAULT_CONSOLE	"console=ttySAC1,115200n8\0"
 
 #define CONFIG_SYS_PROMPT	"Peach-Pi # "
 #define CONFIG_IDENT_STRING	" for Peach-Pi"

include/configs/peach-pit.h

@@ -14,14 +14,20 @@
 #define CONFIG_ENV_SPI_BASE	0x12D30000
 #define FLASH_SIZE		(0x4 << 20)
 #define CONFIG_ENV_OFFSET	(FLASH_SIZE - CONFIG_BL2_SIZE)
+#define CONFIG_SPI_BOOTING
 
 #include <configs/exynos5420-common.h>
 #include <configs/exynos5-dt-common.h>
 
 #define CONFIG_BOARD_COMMON
 
+#define CONFIG_SYS_SDRAM_BASE	0x20000000
+#define CONFIG_SYS_TEXT_BASE	0x23E00000
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_IRAM_TOP - 0x800)
+
 /* select serial console configuration */
 #define CONFIG_SERIAL3		/* use SERIAL 3 */
+#define CONFIG_DEFAULT_CONSOLE	"console=ttySAC1,115200n8\0"
 
 #define CONFIG_SYS_PROMPT	"Peach-Pit # "
 #define CONFIG_IDENT_STRING	" for Peach-Pit"

include/configs/smdk5420.h

@@ -9,20 +9,35 @@
 #ifndef __CONFIG_SMDK5420_H
 #define __CONFIG_SMDK5420_H
 
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SPI_FLASH
+#define CONFIG_ENV_SPI_BASE	0x12D30000
+#define FLASH_SIZE		(0x4 << 20)
+#define CONFIG_ENV_OFFSET	(FLASH_SIZE - CONFIG_BL2_SIZE)
+#define CONFIG_SPI_BOOTING
+
 #include <configs/exynos5420-common.h>
 
 #define CONFIG_BOARD_COMMON
 
 #define CONFIG_SMDK5420			/* which is in a SMDK5420 */
 
+#define CONFIG_SYS_SDRAM_BASE	0x20000000
+#define CONFIG_SYS_TEXT_BASE	0x23E00000
+#define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_IRAM_TOP - 0x800)
 
 /* select serial console configuration */
 #define CONFIG_SERIAL3		/* use SERIAL 3 */
+#define CONFIG_DEFAULT_CONSOLE	"console=ttySAC1,115200n8\0"
 
 #define CONFIG_SYS_PROMPT	"SMDK5420 # "
 #define CONFIG_IDENT_STRING	" for SMDK5420"
 #define CONFIG_DEFAULT_CONSOLE		"console=ttySAC1,115200n8\0"
 
+/* USB */
+#define CONFIG_USB_XHCI
+#define CONFIG_USB_XHCI_EXYNOS
+
 /* DRAM Memory Banks */
 #define CONFIG_NR_DRAM_BANKS	7
 #define SDRAM_BANK_SIZE		(512UL << 20UL)	/* 512 MB */

include/parade.h

@@ -0,0 +1,18 @@
+/*
+ * (C) Copyright 2012 Samsung Electronics
+ * Donghwa Lee <dh09.lee@samsung.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __PARADE_H__
+#define __PARADE_H__
+
+/* Initialize the Parade dP<->LVDS bridge if present */
+#ifdef CONFIG_VIDEO_PARADE
+int parade_init(const void *blob);
+#else
+static inline int parade_init(const void *blob) { return -1; }
+#endif
+
+#endif	/* __PARADE_H__ */