Merge git://git.denx.de/u-boot-usb

arch/arm/cpu/arm926ejs/spear/cpu.c

@@ -47,8 +47,12 @@ int arch_cpu_init(void)
 #if defined(CONFIG_NAND_FSMC)
 	periph1_clken |= MISC_FSMCENB;
 #endif
+#if defined(CONFIG_USB_EHCI_SPEAR)
+	periph1_clken |= PERIPH_USBH1 | PERIPH_USBH2;
+#endif
 
 	writel(periph1_clken, &misc_p->periph1_clken);
+
 	return 0;
 }
 

arch/arm/include/asm/arch-spear/hardware.h

@@ -11,6 +11,8 @@
 #define CONFIG_SYS_USBD_BASE			0xE1100000
 #define CONFIG_SYS_PLUG_BASE			0xE1200000
 #define CONFIG_SYS_FIFO_BASE			0xE1000800
+#define CONFIG_SYS_UHC0_EHCI_BASE		0xE1800000
+#define CONFIG_SYS_UHC1_EHCI_BASE		0xE2000000
 #define CONFIG_SYS_SMI_BASE			0xFC000000
 #define CONFIG_SPEAR_SYSCNTLBASE		0xFCA00000
 #define CONFIG_SPEAR_TIMERBASE			0xFC800000

drivers/usb/gadget/ether.c

@@ -15,6 +15,7 @@
 #include <linux/usb/cdc.h>
 #include <linux/usb/gadget.h>
 #include <net.h>
+#include <usb.h>
 #include <malloc.h>
 #include <linux/ctype.h>
 
@@ -2312,6 +2313,8 @@ static int usb_eth_init(struct eth_device *netdev, bd_t *bd)
 		goto fail;
 	}
 
+	board_usb_init(0, USB_INIT_DEVICE);
+
 	/* Configure default mac-addresses for the USB ethernet device */
 #ifdef CONFIG_USBNET_DEV_ADDR
 	strlcpy(dev_addr, CONFIG_USBNET_DEV_ADDR, sizeof(dev_addr));
@@ -2492,6 +2495,7 @@ void usb_eth_halt(struct eth_device *netdev)
 	}
 
 	usb_gadget_unregister_driver(&eth_driver);
+	board_usb_cleanup(0, USB_INIT_DEVICE);
 }
 
 static struct usb_gadget_driver eth_driver = {
@@ -2501,6 +2505,7 @@ static struct usb_gadget_driver eth_driver = {
 	.unbind		= eth_unbind,
 
 	.setup		= eth_setup,
+	.reset		= eth_disconnect,
 	.disconnect	= eth_disconnect,
 
 	.suspend	= eth_suspend,

drivers/usb/host/Makefile

@@ -37,6 +37,7 @@ obj-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
 obj-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o
 obj-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o
 obj-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o
+obj-$(CONFIG_USB_EHCI_MX7) += ehci-mx6.o
 obj-$(CONFIG_USB_EHCI_OMAP) += ehci-omap.o
 obj-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 obj-$(CONFIG_USB_EHCI_MARVELL) += ehci-marvell.o

drivers/usb/host/dwc2.c

@@ -1113,11 +1113,12 @@ struct dm_usb_ops dwc2_usb_ops = {
 
 static const struct udevice_id dwc2_usb_ids[] = {
 	{ .compatible = "brcm,bcm2835-usb" },
+	{ .compatible = "snps,dwc2" },
 	{ }
 };
 
 U_BOOT_DRIVER(usb_dwc2) = {
-	.name	= "dwc2_exynos",
+	.name	= "dwc2_usb",
 	.id	= UCLASS_USB,
 	.of_match = dwc2_usb_ids,
 	.ofdata_to_platdata = dwc2_usb_ofdata_to_platdata,

drivers/usb/host/ehci-mx6.c

@@ -45,7 +45,10 @@
 #define ANADIG_USB2_PLL_480_CTRL_POWER		0x00001000
 #define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS	0x00000040
 
-
+#define USBNC_OFFSET		0x200
+#define USBNC_PHYSTATUS_ID_DIG	(1 << 4) /* otg_id status */
+#define USBNC_PHYCFG2_ACAENB	(1 << 4) /* otg_id detection enable */
+#define UCTRL_PM                (1 << 9) /* OTG Power Mask */
 #define UCTRL_OVER_CUR_POL	(1 << 8) /* OTG Polarity of Overcurrent */
 #define UCTRL_OVER_CUR_DIS	(1 << 7) /* Disable OTG Overcurrent Detection */
 
@@ -53,6 +56,7 @@
 #define UCMD_RUN_STOP           (1 << 0) /* controller run/stop */
 #define UCMD_RESET		(1 << 1) /* controller reset */
 
+#if defined(CONFIG_MX6)
 static const unsigned phy_bases[] = {
 	USB_PHY0_BASE_ADDR,
 	USB_PHY1_BASE_ADDR,
@@ -67,7 +71,7 @@ static void usb_internal_phy_clock_gate(int index, int on)
 
 	phy_reg = (void __iomem *)phy_bases[index];
 	phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
-	__raw_writel(USBPHY_CTRL_CLKGATE, phy_reg);
+	writel(USBPHY_CTRL_CLKGATE, phy_reg);
 }
 
 static void usb_power_config(int index)
@@ -100,26 +104,52 @@ static void usb_power_config(int index)
 	 * is totally controlled by IC, so the Software only needs
 	 * to enable them at initializtion.
 	 */
-	__raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B |
+	writel(ANADIG_USB2_CHRG_DETECT_EN_B |
 		     ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
 		     chrg_detect);
 
-	__raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
+	writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
 		     pll_480_ctrl_clr);
 
-	__raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
+	writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
 		     ANADIG_USB2_PLL_480_CTRL_POWER |
 		     ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
 		     pll_480_ctrl_set);
 }
 
+static int wait_for_bit(u32 *reg, const u32 mask, bool set)
+{
+	u32 val;
+	const unsigned int timeout = 10000;
+	unsigned long start = get_timer(0);
+
+	while(1) {
+		val = readl(reg);
+		if (!set)
+			val = ~val;
+
+		if ((val & mask) == mask)
+			return 0;
+
+		if (get_timer(start) > timeout)
+			break;
+
+		udelay(1);
+	}
+
+	debug("%s: Timeout (reg=%p mask=%08x wait_set=%i)\n",
+			__func__, reg, mask, set);
+
+	return -ETIMEDOUT;
+}
+
 /* Return 0 : host node, <>0 : device mode */
 static int usb_phy_enable(int index, struct usb_ehci *ehci)
 {
 	void __iomem *phy_reg;
 	void __iomem *phy_ctrl;
 	void __iomem *usb_cmd;
-	u32 val;
+	int ret;
 
 	if (index >= ARRAY_SIZE(phy_bases))
 		return 0;
@@ -129,70 +159,33 @@ static int usb_phy_enable(int index, struct usb_ehci *ehci)
 	usb_cmd = (void __iomem *)&ehci->usbcmd;
 
 	/* Stop then Reset */
-	val = __raw_readl(usb_cmd);
+	clrbits_le32(usb_cmd, UCMD_RUN_STOP);
-	val &= ~UCMD_RUN_STOP;
+	ret = wait_for_bit(usb_cmd, UCMD_RUN_STOP, 0);
-	__raw_writel(val, usb_cmd);
+	if (ret)
-	while (__raw_readl(usb_cmd) & UCMD_RUN_STOP)
+		return ret;
-		;
 
-	val = __raw_readl(usb_cmd);
+	setbits_le32(usb_cmd, UCMD_RESET);
-	val |= UCMD_RESET;
+	ret = wait_for_bit(usb_cmd, UCMD_RESET, 0);
-	__raw_writel(val, usb_cmd);
+	if (ret)
-	while (__raw_readl(usb_cmd) & UCMD_RESET)
+		return ret;
-		;
 
 	/* Reset USBPHY module */
-	val = __raw_readl(phy_ctrl);
+	setbits_le32(phy_ctrl, USBPHY_CTRL_SFTRST);
-	val |= USBPHY_CTRL_SFTRST;
-	__raw_writel(val, phy_ctrl);
 	udelay(10);
 
 	/* Remove CLKGATE and SFTRST */
-	val = __raw_readl(phy_ctrl);
+	clrbits_le32(phy_ctrl, USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
-	val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
-	__raw_writel(val, phy_ctrl);
 	udelay(10);
 
 	/* Power up the PHY */
-	__raw_writel(0, phy_reg + USBPHY_PWD);
+	writel(0, phy_reg + USBPHY_PWD);
 	/* enable FS/LS device */
-	val = __raw_readl(phy_ctrl);
+	setbits_le32(phy_ctrl, USBPHY_CTRL_ENUTMILEVEL2 |
-	val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
+			USBPHY_CTRL_ENUTMILEVEL3);
-	__raw_writel(val, phy_ctrl);
 
 	return 0;
 }
 
-/* Base address for this IP block is 0x02184800 */
-struct usbnc_regs {
-	u32	ctrl[4];	/* otg/host1-3 */
-	u32	uh2_hsic_ctrl;
-	u32	uh3_hsic_ctrl;
-	u32	otg_phy_ctrl_0;
-	u32	uh1_phy_ctrl_0;
-};
-
-static void usb_oc_config(int index)
-{
-	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
-			USB_OTHERREGS_OFFSET);
-	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
-	u32 val;
-
-	val = __raw_readl(ctrl);
-#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
-	/* mx6qarm2 seems to required a different setting*/
-	val &= ~UCTRL_OVER_CUR_POL;
-#else
-	val |= UCTRL_OVER_CUR_POL;
-#endif
-	__raw_writel(val, ctrl);
-
-	val = __raw_readl(ctrl);
-	val |= UCTRL_OVER_CUR_DIS;
-	__raw_writel(val, ctrl);
-}
-
 int usb_phy_mode(int port)
 {
 	void __iomem *phy_reg;
@@ -202,7 +195,7 @@ int usb_phy_mode(int port)
 	phy_reg = (void __iomem *)phy_bases[port];
 	phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
 
-	val = __raw_readl(phy_ctrl);
+	val = readl(phy_ctrl);
 
 	if (val & USBPHY_CTRL_OTG_ID)
 		return USB_INIT_DEVICE;
@@ -210,16 +203,121 @@ int usb_phy_mode(int port)
 		return USB_INIT_HOST;
 }
 
+/* Base address for this IP block is 0x02184800 */
+struct usbnc_regs {
+	u32	ctrl[4];	/* otg/host1-3 */
+	u32	uh2_hsic_ctrl;
+	u32	uh3_hsic_ctrl;
+	u32	otg_phy_ctrl_0;
+	u32	uh1_phy_ctrl_0;
+};
+#elif defined(CONFIG_MX7)
+struct usbnc_regs {
+	u32 ctrl1;
+	u32 ctrl2;
+	u32 reserve1[10];
+	u32 phy_cfg1;
+	u32 phy_cfg2;
+	u32 phy_status;
+	u32 reserve2[4];
+	u32 adp_cfg1;
+	u32 adp_cfg2;
+	u32 adp_status;
+};
+
+static void usb_power_config(int index)
+{
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			(0x10000 * index) + USBNC_OFFSET);
+	void __iomem *phy_cfg2 = (void __iomem *)(&usbnc->phy_cfg2);
+
+	/* Enable usb_otg_id detection */
+	setbits_le32(phy_cfg2, USBNC_PHYCFG2_ACAENB);
+}
+
+int usb_phy_mode(int port)
+{
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			(0x10000 * port) + USBNC_OFFSET);
+	void __iomem *status = (void __iomem *)(&usbnc->phy_status);
+	u32 val;
+
+	val = readl(status);
+
+	if (val & USBNC_PHYSTATUS_ID_DIG)
+		return USB_INIT_DEVICE;
+	else
+		return USB_INIT_HOST;
+}
+#endif
+
+static void usb_oc_config(int index)
+{
+#if defined(CONFIG_MX6)
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			USB_OTHERREGS_OFFSET);
+	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl[index]);
+#elif defined(CONFIG_MX7)
+	struct usbnc_regs *usbnc = (struct usbnc_regs *)(USB_BASE_ADDR +
+			(0x10000 * index) + USBNC_OFFSET);
+	void __iomem *ctrl = (void __iomem *)(&usbnc->ctrl1);
+#endif
+
+#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
+	/* mx6qarm2 seems to required a different setting*/
+	clrbits_le32(ctrl, UCTRL_OVER_CUR_POL);
+#else
+	setbits_le32(ctrl, UCTRL_OVER_CUR_POL);
+#endif
+
+#if defined(CONFIG_MX6)
+	setbits_le32(ctrl, UCTRL_OVER_CUR_DIS);
+#elif defined(CONFIG_MX7)
+	setbits_le32(ctrl, UCTRL_OVER_CUR_DIS | UCTRL_PM);
+#endif
+}
+
+/**
+ * board_ehci_hcd_init - override usb phy mode
+ * @port:	usb host/otg port
+ *
+ * Target board specific, override usb_phy_mode.
+ * When usb-otg is used as usb host port, iomux pad usb_otg_id can be
+ * left disconnected in this case usb_phy_mode will not be able to identify
+ * the phy mode that usb port is used.
+ * Machine file overrides board_usb_phy_mode.
+ *
+ * Return: USB_INIT_DEVICE or USB_INIT_HOST
+ */
 int __weak board_usb_phy_mode(int port)
 {
 	return usb_phy_mode(port);
 }
 
+/**
+ * board_ehci_hcd_init - set usb vbus voltage
+ * @port:      usb otg port
+ *
+ * Target board specific, setup iomux pad to setup supply vbus voltage
+ * for usb otg port. Machine board file overrides board_ehci_hcd_init
+ *
+ * Return: 0 Success
+ */
 int __weak board_ehci_hcd_init(int port)
 {
 	return 0;
 }
 
+/**
+ * board_ehci_power - enables/disables usb vbus voltage
+ * @port:      usb otg port
+ * @on:        on/off vbus voltage
+ *
+ * Enables/disables supply vbus voltage for usb otg port.
+ * Machine board file overrides board_ehci_power
+ *
+ * Return: 0 Success
+ */
 int __weak board_ehci_power(int port, int on)
 {
 	return 0;
@@ -229,8 +327,13 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
 {
 	enum usb_init_type type;
+#if defined(CONFIG_MX6)
+	u32 controller_spacing = 0x200;
+#elif defined(CONFIG_MX7)
+	u32 controller_spacing = 0x10000;
+#endif
 	struct usb_ehci *ehci = (struct usb_ehci *)(USB_BASE_ADDR +
-		(0x200 * index));
+		(controller_spacing * index));
 
 	if (index > 3)
 		return -EINVAL;
@@ -242,8 +345,11 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 
 	usb_power_config(index);
 	usb_oc_config(index);
+
+#if defined(CONFIG_MX6)
 	usb_internal_phy_clock_gate(index, 1);
 	usb_phy_enable(index, ehci);
+#endif
 	type = board_usb_phy_mode(index);
 
 	*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
@@ -256,8 +362,9 @@ int ehci_hcd_init(int index, enum usb_init_type init,
 		return -ENODEV;
 	if (type == USB_INIT_DEVICE)
 		return 0;
+
 	setbits_le32(&ehci->usbmode, CM_HOST);
-	__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
+	writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
 	setbits_le32(&ehci->portsc, USB_EN);
 
 	mdelay(10);

drivers/usb/host/ehci-spear.c

@@ -14,7 +14,21 @@
 #include <usb.h>
 #include "ehci.h"
 #include <asm/arch/hardware.h>
+#include <asm/arch/spr_misc.h>
 
+static void spear6xx_usbh_stop(void)
+{
+	struct misc_regs *const misc_p =
+	    (struct misc_regs *)CONFIG_SPEAR_MISCBASE;
+	u32 periph1_rst = readl(misc_p->periph1_rst);
+
+	periph1_rst |= PERIPH_USBH1 | PERIPH_USBH2;
+	writel(periph1_rst, misc_p->periph1_rst);
+
+	udelay(1000);
+	periph1_rst &= ~(PERIPH_USBH1 | PERIPH_USBH2);
+	writel(periph1_rst, misc_p->periph1_rst);
+}
 
 /*
  * Create the appropriate control structures to manage
@@ -23,9 +37,23 @@
 int ehci_hcd_init(int index, enum usb_init_type init,
 		struct ehci_hccr **hccr, struct ehci_hcor **hcor)
 {
-	*hccr = (struct ehci_hccr *)(CONFIG_SYS_UHC0_EHCI_BASE + 0x100);
+	u32 ehci = 0;
-	*hcor = (struct ehci_hcor *)((uint32_t)*hccr
+
-			+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+	switch (index) {
+	case 0:
+		ehci = CONFIG_SYS_UHC0_EHCI_BASE;
+		break;
+	case 1:
+		ehci = CONFIG_SYS_UHC1_EHCI_BASE;
+		break;
+	default:
+		printf("ERROR: wrong controller index!\n");
+		break;
+	};
+
+	*hccr = (struct ehci_hccr *)(ehci + 0x100);
+	*hcor = (struct ehci_hcor *)((uint32_t) *hccr +
+			HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
 
 	debug("SPEAr-ehci: init hccr %x and hcor %x hc_length %d\n",
 		(uint32_t)*hccr, (uint32_t)*hcor,
@@ -40,5 +68,9 @@ int ehci_hcd_init(int index, enum usb_init_type init,
  */
 int ehci_hcd_stop(int index)
 {
+#if defined(CONFIG_SPEAR600)
+	spear6xx_usbh_stop();
+#endif
+
 	return 0;
 }

drivers/usb/host/xhci-omap.c

@@ -96,4 +96,5 @@ void xhci_hcd_stop(int index)
 	struct omap_xhci *ctx = &omap;
 
 	omap_xhci_core_exit(ctx);
+	board_usb_cleanup(index, USB_INIT_HOST);
 }

drivers/usb/host/xhci.c

@@ -199,7 +199,7 @@ int xhci_reset(struct xhci_hcor *hcor)
 	int ret;
 
 	/* Halting the Host first */
-	debug("// Halt the HC\n");
+	debug("// Halt the HC: %p\n", hcor);
 	state = xhci_readl(&hcor->or_usbsts) & STS_HALT;
 	if (!state) {
 		cmd = xhci_readl(&hcor->or_usbcmd);
@@ -1064,6 +1064,8 @@ int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
 	struct xhci_ctrl *ctrl;
 	int ret;
 
+	*controller = NULL;
+
 	if (xhci_hcd_init(index, &hccr, (struct xhci_hcor **)&hcor) != 0)
 		return -ENODEV;
 
@@ -1077,7 +1079,12 @@ int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
 
 	ret = xhci_lowlevel_init(ctrl);
 
-	*controller = &xhcic[index];
+	if (ret) {
+		ctrl->hccr = NULL;
+		ctrl->hcor = NULL;
+	} else {
+		*controller = &xhcic[index];
+	}
 
 	return ret;
 }
@@ -1093,9 +1100,11 @@ int usb_lowlevel_stop(int index)
 {
 	struct xhci_ctrl *ctrl = (xhcic + index);
 
-	xhci_lowlevel_stop(ctrl);
+	if (ctrl->hcor) {
-	xhci_hcd_stop(index);
+		xhci_lowlevel_stop(ctrl);
-	xhci_cleanup(ctrl);
+		xhci_hcd_stop(index);
+		xhci_cleanup(ctrl);
+	}
 
 	return 0;
 }