Blackfin: unify common ADI board settings
Rather than duplicate the same ADI settings in every ADI board, create a common ADI config header and have all ADI boards start using that. This will also make merging the ~10 boards I have to forward port a lot easier. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This commit is contained in:
Mike Frysinger
parent
74398b23f9
commit
cf6f469e27
|
|
@ -2,213 +2,155 @@
|
||||||
* U-boot - Configuration file for BF533 EZKIT board
|
* U-boot - Configuration file for BF533 EZKIT board
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#ifndef __CONFIG_EZKIT533_H__
|
#ifndef __CONFIG_BF533_EZKIT_H__
|
||||||
#define __CONFIG_EZKIT533_H__
|
#define __CONFIG_BF533_EZKIT_H__
|
||||||
|
|
||||||
#include <asm/blackfin-config-pre.h>
|
#include <asm/blackfin-config-pre.h>
|
||||||
|
|
||||||
#define CONFIG_BAUDRATE 57600
|
|
||||||
|
|
||||||
#define CONFIG_BOOTDELAY 5
|
/*
|
||||||
#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
|
* Processor Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_BFIN_CPU bf533-0.3
|
||||||
|
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
||||||
|
|
||||||
#define CONFIG_SYS_LONGHELP 1
|
|
||||||
#define CONFIG_CMDLINE_EDITING 1
|
|
||||||
#define CONFIG_LOADADDR 0x01000000 /* default load address */
|
|
||||||
#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
|
|
||||||
/* #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" */
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Clock Settings
|
||||||
|
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
|
||||||
|
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
|
||||||
|
*/
|
||||||
|
/* CONFIG_CLKIN_HZ is any value in Hz */
|
||||||
|
#define CONFIG_CLKIN_HZ 27000000
|
||||||
|
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
|
||||||
|
/* 1 = CLKIN / 2 */
|
||||||
|
#define CONFIG_CLKIN_HALF 0
|
||||||
|
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
|
||||||
|
/* 1 = bypass PLL */
|
||||||
|
#define CONFIG_PLL_BYPASS 0
|
||||||
|
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
|
||||||
|
/* Values can range from 0-63 (where 0 means 64) */
|
||||||
|
#define CONFIG_VCO_MULT 22
|
||||||
|
/* CCLK_DIV controls the core clock divider */
|
||||||
|
/* Values can be 1, 2, 4, or 8 ONLY */
|
||||||
|
#define CONFIG_CCLK_DIV 1
|
||||||
|
/* SCLK_DIV controls the system clock divider */
|
||||||
|
/* Values can range from 1-15 */
|
||||||
|
#define CONFIG_SCLK_DIV 5
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Memory Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_MEM_SIZE 32
|
||||||
|
/* Early EZKITs had 32megs, but later have 64megs */
|
||||||
|
#if (CONFIG_MEM_SIZE == 64)
|
||||||
|
# define CONFIG_MEM_ADD_WDTH 10
|
||||||
|
#else
|
||||||
|
# define CONFIG_MEM_ADD_WDTH 9
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_SDRRC_VAL 0x398
|
||||||
|
#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
|
||||||
|
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
|
||||||
|
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
|
||||||
|
|
||||||
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
|
||||||
|
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Network Settings
|
||||||
|
*/
|
||||||
|
#define ADI_CMDS_NETWORK 1
|
||||||
#define CONFIG_DRIVER_SMC91111 1
|
#define CONFIG_DRIVER_SMC91111 1
|
||||||
#define CONFIG_SMC91111_BASE 0x20310300
|
#define CONFIG_SMC91111_BASE 0x20310300
|
||||||
|
#define SMC91111_EEPROM_INIT() \
|
||||||
#if 0
|
do { \
|
||||||
#define CONFIG_MII
|
*pFIO_DIR |= PF1; \
|
||||||
#define CONFIG_SYS_DISCOVER_PHY
|
*pFIO_FLAG_S = PF1; \
|
||||||
#endif
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
#define CONFIG_RTC_BFIN 1
|
#define CONFIG_HOSTNAME bf533-ezkit
|
||||||
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
|
/* Uncomment next line to use fixed MAC address */
|
||||||
|
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
|
||||||
#define CONFIG_PANIC_HANG 1
|
|
||||||
|
|
||||||
#define CONFIG_BFIN_CPU bf533-0.3
|
|
||||||
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
|
||||||
|
|
||||||
/* This sets the default state of the cache on U-Boot's boot */
|
|
||||||
#define CONFIG_ICACHE_ON
|
|
||||||
#define CONFIG_DCACHE_ON
|
|
||||||
|
|
||||||
/* CONFIG_CLKIN_HZ is any value in Hz */
|
|
||||||
#define CONFIG_CLKIN_HZ 27000000
|
|
||||||
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
|
|
||||||
/* 1=CLKIN/2 */
|
|
||||||
#define CONFIG_CLKIN_HALF 0
|
|
||||||
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
|
|
||||||
/* 1=bypass PLL */
|
|
||||||
#define CONFIG_PLL_BYPASS 0
|
|
||||||
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
|
|
||||||
/* Values can range from 1-64 */
|
|
||||||
#define CONFIG_VCO_MULT 22
|
|
||||||
/* CONFIG_CCLK_DIV controls what the core clock divider is */
|
|
||||||
/* Values can be 1, 2, 4, or 8 ONLY */
|
|
||||||
#define CONFIG_CCLK_DIV 1
|
|
||||||
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
|
|
||||||
/* Values can range from 1-15 */
|
|
||||||
#define CONFIG_SCLK_DIV 5
|
|
||||||
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
|
|
||||||
/* Values can range from 2-65535 */
|
|
||||||
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
|
|
||||||
#define CONFIG_SPI_BAUD 2
|
|
||||||
#define CONFIG_SPI_BAUD_INITBLOCK 4
|
|
||||||
|
|
||||||
#if ( CONFIG_CLKIN_HALF == 0 )
|
|
||||||
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
|
|
||||||
#else
|
|
||||||
#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if (CONFIG_PLL_BYPASS == 0)
|
|
||||||
#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
|
|
||||||
#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
|
|
||||||
#else
|
|
||||||
#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
|
|
||||||
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */
|
|
||||||
#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
|
|
||||||
#define CONFIG_MEM_MT48LC16M16A2TG_75 1
|
|
||||||
|
|
||||||
#define CONFIG_LOADS_ECHO 1
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* BOOTP options
|
* Flash Settings
|
||||||
*/
|
*/
|
||||||
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
||||||
#define CONFIG_BOOTP_BOOTPATH
|
|
||||||
#define CONFIG_BOOTP_GATEWAY
|
|
||||||
#define CONFIG_BOOTP_HOSTNAME
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Command line configuration.
|
|
||||||
*/
|
|
||||||
#include <config_cmd_default.h>
|
|
||||||
|
|
||||||
#define CONFIG_CMD_PING
|
|
||||||
#define CONFIG_CMD_ELF
|
|
||||||
#define CONFIG_CMD_I2C
|
|
||||||
#define CONFIG_CMD_JFFS2
|
|
||||||
#define CONFIG_CMD_DATE
|
|
||||||
|
|
||||||
|
|
||||||
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
|
|
||||||
|
|
||||||
#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
|
|
||||||
#if defined(CONFIG_CMD_KGDB)
|
|
||||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
||||||
#else
|
|
||||||
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
||||||
#endif
|
|
||||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
||||||
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
||||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
||||||
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
|
|
||||||
#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
|
|
||||||
#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* default load address */
|
|
||||||
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
|
|
||||||
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
||||||
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
||||||
#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
|
|
||||||
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
||||||
|
#define CONFIG_SYS_MAX_FLASH_BANKS 3
|
||||||
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
#define CONFIG_SYS_MAX_FLASH_SECT 40
|
||||||
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
|
#define CONFIG_ENV_IS_IN_FLASH
|
||||||
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
||||||
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
|
|
||||||
#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
|
|
||||||
#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
|
|
||||||
#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
|
|
||||||
|
|
||||||
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
||||||
#define CONFIG_SYS_FLASH0_BASE 0x20000000
|
|
||||||
#define CONFIG_SYS_FLASH1_BASE 0x20200000
|
|
||||||
#define CONFIG_SYS_FLASH2_BASE 0x20280000
|
|
||||||
#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
|
|
||||||
#define CONFIG_SYS_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
|
|
||||||
|
|
||||||
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
||||||
#define CONFIG_ENV_ADDR 0x20020000
|
#define CONFIG_ENV_ADDR 0x20020000
|
||||||
#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
||||||
|
|
||||||
/* JFFS Partition offset set */
|
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
|
|
||||||
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
|
|
||||||
/* 512k reserved for u-boot */
|
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Stack sizes
|
|
||||||
*/
|
|
||||||
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
|
|
||||||
|
|
||||||
#define POLL_MODE 1
|
|
||||||
#define FLASH_TOT_SECT 40
|
#define FLASH_TOT_SECT 40
|
||||||
#define FLASH_SIZE 0x220000
|
|
||||||
#define CONFIG_SYS_FLASH_SIZE 0x220000
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Initialize PSD4256 registers for using I2C
|
* I2C Settings
|
||||||
*/
|
|
||||||
#define CONFIG_MISC_INIT_R
|
|
||||||
|
|
||||||
/*
|
|
||||||
* I2C settings
|
|
||||||
* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
|
* By default PF1 is used as SDA and PF0 as SCL on the Stamp board
|
||||||
*/
|
*/
|
||||||
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
|
#define CONFIG_SOFT_I2C
|
||||||
/*
|
#ifdef CONFIG_SOFT_I2C
|
||||||
* Software (bit-bang) I2C driver configuration
|
#define PF_SCL PF0
|
||||||
*/
|
#define PF_SDA PF1
|
||||||
#define PF_SCL PF0
|
#define I2C_INIT \
|
||||||
#define PF_SDA PF1
|
do { \
|
||||||
|
*pFIO_DIR |= PF_SCL; \
|
||||||
#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
|
SSYNC(); \
|
||||||
#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
|
} while (0)
|
||||||
#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
|
#define I2C_ACTIVE \
|
||||||
#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
|
do { \
|
||||||
#define I2C_SDA(bit) if(bit) { \
|
*pFIO_DIR |= PF_SDA; \
|
||||||
*pFIO_FLAG_S = PF_SDA; \
|
*pFIO_INEN &= ~PF_SDA; \
|
||||||
asm("ssync;"); \
|
SSYNC(); \
|
||||||
} \
|
} while (0)
|
||||||
else { \
|
#define I2C_TRISTATE \
|
||||||
*pFIO_FLAG_C = PF_SDA; \
|
do { \
|
||||||
asm("ssync;"); \
|
*pFIO_DIR &= ~PF_SDA; \
|
||||||
}
|
*pFIO_INEN |= PF_SDA; \
|
||||||
#define I2C_SCL(bit) if(bit) { \
|
SSYNC(); \
|
||||||
*pFIO_FLAG_S = PF_SCL; \
|
} while (0)
|
||||||
asm("ssync;"); \
|
#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
|
||||||
} \
|
#define I2C_SDA(bit) \
|
||||||
else { \
|
do { \
|
||||||
*pFIO_FLAG_C = PF_SCL; \
|
if (bit) \
|
||||||
asm("ssync;"); \
|
*pFIO_FLAG_S = PF_SDA; \
|
||||||
}
|
else \
|
||||||
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
*pFIO_FLAG_C = PF_SDA; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_SCL(bit) \
|
||||||
|
do { \
|
||||||
|
if (bit) \
|
||||||
|
*pFIO_FLAG_S = PF_SCL; \
|
||||||
|
else \
|
||||||
|
*pFIO_FLAG_C = PF_SCL; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
||||||
|
|
||||||
#define CONFIG_SYS_I2C_SPEED 50000
|
#define CONFIG_SYS_I2C_SPEED 50000
|
||||||
#define CONFIG_SYS_I2C_SLAVE 0
|
#define CONFIG_SYS_I2C_SLAVE 0
|
||||||
|
#endif
|
||||||
|
|
||||||
#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
|
|
||||||
|
|
||||||
#define CONFIG_EBIU_SDRRC_VAL 0x398
|
/*
|
||||||
#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
|
* Misc Settings
|
||||||
#define CONFIG_EBIU_SDBCTL_VAL 0x13
|
*/
|
||||||
|
#define CONFIG_MISC_INIT_R
|
||||||
|
#define CONFIG_RTC_BFIN
|
||||||
|
#define CONFIG_UART_CONSOLE 0
|
||||||
|
|
||||||
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
|
|
||||||
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
|
/*
|
||||||
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
|
* Pull in common ADI header for remaining command/environment setup
|
||||||
|
*/
|
||||||
|
#include <configs/bfin_adi_common.h>
|
||||||
|
|
||||||
#include <asm/blackfin-config-post.h>
|
#include <asm/blackfin-config-post.h>
|
||||||
|
|
||||||
|
|
|
||||||
|
|
@ -2,371 +2,219 @@
|
||||||
* U-boot - Configuration file for BF533 STAMP board
|
* U-boot - Configuration file for BF533 STAMP board
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#ifndef __CONFIG_STAMP_H__
|
#ifndef __CONFIG_BF533_STAMP_H__
|
||||||
#define __CONFIG_STAMP_H__
|
#define __CONFIG_BF533_STAMP_H__
|
||||||
|
|
||||||
#include <asm/blackfin-config-pre.h>
|
#include <asm/blackfin-config-pre.h>
|
||||||
|
|
||||||
#define CONFIG_RTC_BFIN 1
|
|
||||||
|
|
||||||
#define CONFIG_PANIC_HANG 1
|
|
||||||
|
|
||||||
#define CONFIG_BFIN_CPU bf533-0.3
|
|
||||||
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
|
||||||
|
|
||||||
/* This sets the default state of the cache on U-Boot's boot */
|
|
||||||
#define CONFIG_ICACHE_ON
|
|
||||||
#define CONFIG_DCACHE_ON
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Board settings
|
* Processor Settings
|
||||||
*/
|
*/
|
||||||
|
#define CONFIG_BFIN_CPU bf533-0.3
|
||||||
|
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Clock Settings
|
||||||
|
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
|
||||||
|
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
|
||||||
|
*/
|
||||||
|
/* CONFIG_CLKIN_HZ is any value in Hz */
|
||||||
|
#define CONFIG_CLKIN_HZ 11059200
|
||||||
|
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
|
||||||
|
/* 1 = CLKIN / 2 */
|
||||||
|
#define CONFIG_CLKIN_HALF 0
|
||||||
|
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
|
||||||
|
/* 1 = bypass PLL */
|
||||||
|
#define CONFIG_PLL_BYPASS 0
|
||||||
|
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
|
||||||
|
/* Values can range from 0-63 (where 0 means 64) */
|
||||||
|
#define CONFIG_VCO_MULT 36
|
||||||
|
/* CCLK_DIV controls the core clock divider */
|
||||||
|
/* Values can be 1, 2, 4, or 8 ONLY */
|
||||||
|
#define CONFIG_CCLK_DIV 1
|
||||||
|
/* SCLK_DIV controls the system clock divider */
|
||||||
|
/* Values can range from 1-15 */
|
||||||
|
#define CONFIG_SCLK_DIV 5
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Memory Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_MEM_ADD_WDTH 11
|
||||||
|
#define CONFIG_MEM_SIZE 128
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_SDRRC_VAL 0x268
|
||||||
|
#define CONFIG_EBIU_SDGCTL_VAL 0x911109
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
|
||||||
|
#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
|
||||||
|
#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
|
||||||
|
|
||||||
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
|
||||||
|
#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Network Settings
|
||||||
|
*/
|
||||||
|
#define ADI_CMDS_NETWORK 1
|
||||||
#define CONFIG_DRIVER_SMC91111 1
|
#define CONFIG_DRIVER_SMC91111 1
|
||||||
#define CONFIG_SMC91111_BASE 0x20300300
|
#define CONFIG_SMC91111_BASE 0x20300300
|
||||||
|
#define SMC91111_EEPROM_INIT() \
|
||||||
|
do { \
|
||||||
|
*pFIO_DIR |= PF1; \
|
||||||
|
*pFIO_FLAG_S = PF1; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define CONFIG_HOSTNAME bf533-stamp
|
||||||
|
/* Uncomment next line to use fixed MAC address */
|
||||||
|
/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
|
||||||
|
|
||||||
/* FLASH/ETHERNET uses the same address range */
|
|
||||||
#define SHARED_RESOURCES 1
|
|
||||||
|
|
||||||
/* Is I2C bit-banged? */
|
|
||||||
#define CONFIG_SOFT_I2C 1
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Software (bit-bang) I2C driver configuration
|
* Flash Settings
|
||||||
*/
|
*/
|
||||||
#define PF_SCL PF3
|
#define CONFIG_FLASH_CFI_DRIVER
|
||||||
#define PF_SDA PF2
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Video splash screen support
|
|
||||||
*/
|
|
||||||
#define CONFIG_VIDEO 0
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Clock settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
/* CONFIG_CLKIN_HZ is any value in Hz */
|
|
||||||
#define CONFIG_CLKIN_HZ 11059200
|
|
||||||
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
|
|
||||||
/* 1=CLKIN/2 */
|
|
||||||
#define CONFIG_CLKIN_HALF 0
|
|
||||||
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
|
|
||||||
/* 1=bypass PLL */
|
|
||||||
#define CONFIG_PLL_BYPASS 0
|
|
||||||
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
|
|
||||||
/* Values can range from 1-64 */
|
|
||||||
#define CONFIG_VCO_MULT 36
|
|
||||||
/* CONFIG_CCLK_DIV controls what the core clock divider is */
|
|
||||||
/* Values can be 1, 2, 4, or 8 ONLY */
|
|
||||||
#define CONFIG_CCLK_DIV 1
|
|
||||||
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
|
|
||||||
/* Values can range from 1-15 */
|
|
||||||
#define CONFIG_SCLK_DIV 5
|
|
||||||
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
|
|
||||||
/* Values can range from 2-65535 */
|
|
||||||
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
|
|
||||||
#define CONFIG_SPI_BAUD 2
|
|
||||||
#define CONFIG_SPI_BAUD_INITBLOCK 4
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Network settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
#if (CONFIG_DRIVER_SMC91111)
|
|
||||||
#if 0
|
|
||||||
#define CONFIG_MII
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/* network support */
|
|
||||||
#define CONFIG_IPADDR 192.168.0.15
|
|
||||||
#define CONFIG_NETMASK 255.255.255.0
|
|
||||||
#define CONFIG_GATEWAYIP 192.168.0.1
|
|
||||||
#define CONFIG_SERVERIP 192.168.0.2
|
|
||||||
#define CONFIG_HOSTNAME STAMP
|
|
||||||
#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
|
|
||||||
|
|
||||||
/* To remove hardcoding and enable MAC storage in EEPROM */
|
|
||||||
/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
|
|
||||||
#endif /* CONFIG_DRIVER_SMC91111 */
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Flash settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
|
||||||
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
|
||||||
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
||||||
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
#define CONFIG_SYS_FLASH_CFI
|
||||||
#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
|
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
|
||||||
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
||||||
|
#define CONFIG_SYS_MAX_FLASH_SECT 67
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* SPI Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_BFIN_SPI
|
||||||
|
#define CONFIG_ENV_SPI_MAX_HZ 30000000
|
||||||
|
#define CONFIG_SF_DEFAULT_HZ 30000000
|
||||||
|
#define CONFIG_SPI_FLASH
|
||||||
|
#define CONFIG_SPI_FLASH_ATMEL
|
||||||
|
#define CONFIG_SPI_FLASH_SPANSION
|
||||||
|
#define CONFIG_SPI_FLASH_STMICRO
|
||||||
|
#define CONFIG_SPI_FLASH_WINBOND
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Env Storage Settings
|
||||||
|
*/
|
||||||
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
|
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
|
||||||
#define CONFIG_ENV_IS_IN_EEPROM 1
|
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
||||||
#define CONFIG_ENV_OFFSET 0x4000
|
#define CONFIG_ENV_OFFSET 0x4000
|
||||||
#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
|
#define CONFIG_ENV_SIZE 0x2000
|
||||||
|
#define CONFIG_ENV_SECT_SIZE 0x2000
|
||||||
#else
|
#else
|
||||||
#define CONFIG_ENV_IS_IN_FLASH 1
|
#define CONFIG_ENV_IS_IN_FLASH
|
||||||
#define CONFIG_ENV_ADDR 0x20004000
|
#define CONFIG_ENV_OFFSET 0x4000
|
||||||
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
|
||||||
|
#define CONFIG_ENV_SIZE 0x2000
|
||||||
|
#define CONFIG_ENV_SECT_SIZE 0x2000
|
||||||
#endif
|
#endif
|
||||||
|
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
|
||||||
#define CONFIG_ENV_SIZE 0x2000
|
#define ENV_IS_EMBEDDED
|
||||||
#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
|
|
||||||
#define ENV_IS_EMBEDDED
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
|
|
||||||
#define CONFIG_SYS_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
|
|
||||||
#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
|
|
||||||
|
|
||||||
/* JFFS Partition offset set */
|
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
|
|
||||||
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
|
|
||||||
/* 512k reserved for u-boot */
|
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
|
|
||||||
|
|
||||||
/*
|
|
||||||
* following timeouts shall be used once the
|
|
||||||
* Flash real protection is enabled
|
|
||||||
*/
|
|
||||||
#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
|
|
||||||
#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
|
|
||||||
|
|
||||||
/*
|
|
||||||
* SDRAM settings & memory map
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
|
|
||||||
#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
|
|
||||||
#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
|
|
||||||
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MAX_RAM_SIZE - 0x80000 - 1)
|
|
||||||
#define CONFIG_LOADADDR 0x01000000
|
|
||||||
|
|
||||||
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
||||||
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
||||||
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
||||||
#define CONFIG_SYS_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
|
|
||||||
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - 0x40000)
|
|
||||||
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
|
|
||||||
#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
|
|
||||||
#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
|
|
||||||
|
|
||||||
/* Check to make sure everything fits in SDRAM */
|
|
||||||
#if ((CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) > CONFIG_SYS_MAX_RAM_SIZE)
|
|
||||||
#error Memory Map does not fit into configuration
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if ( CONFIG_CLKIN_HALF == 0 )
|
|
||||||
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
|
|
||||||
#else
|
#else
|
||||||
#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
|
#define ENV_IS_EMBEDDED_CUSTOM
|
||||||
#endif
|
|
||||||
|
|
||||||
#if (CONFIG_PLL_BYPASS == 0)
|
|
||||||
#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
|
|
||||||
#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
|
|
||||||
#else
|
|
||||||
#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
|
|
||||||
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Command settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_SYS_LONGHELP 1
|
|
||||||
#define CONFIG_CMDLINE_EDITING 1
|
|
||||||
|
|
||||||
#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
|
|
||||||
|
|
||||||
/* configuration lookup from the BOOTP/DHCP server, */
|
|
||||||
/* but not try to load any image using TFTP */
|
|
||||||
|
|
||||||
#define CONFIG_BOOTDELAY 5
|
|
||||||
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
|
|
||||||
#define CONFIG_BOOTCOMMAND "run ramboot"
|
|
||||||
|
|
||||||
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
|
|
||||||
|
|
||||||
|
|
||||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
||||||
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
|
|
||||||
"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
|
|
||||||
"$(rootpath) console=ttyBF0,57600\0" \
|
|
||||||
"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
|
|
||||||
"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
|
|
||||||
"ramboot=tftpboot $(loadaddr) linux; " \
|
|
||||||
"run ramargs;run addip;bootelf\0" \
|
|
||||||
"nfsboot=tftpboot $(loadaddr) linux; " \
|
|
||||||
"run nfsargs;run addip;bootelf\0" \
|
|
||||||
"flashboot=bootm 0x20100000\0" \
|
|
||||||
"update=tftpboot $(loadaddr) u-boot.bin; " \
|
|
||||||
"protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
|
|
||||||
"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
|
|
||||||
""
|
|
||||||
|
|
||||||
#ifdef CONFIG_SOFT_I2C
|
|
||||||
#if (!CONFIG_SOFT_I2C)
|
|
||||||
#undef CONFIG_SOFT_I2C
|
|
||||||
#endif
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* BOOTP options
|
* I2C Settings
|
||||||
*/
|
|
||||||
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
||||||
#define CONFIG_BOOTP_BOOTPATH
|
|
||||||
#define CONFIG_BOOTP_GATEWAY
|
|
||||||
#define CONFIG_BOOTP_HOSTNAME
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Command line configuration.
|
|
||||||
*/
|
|
||||||
#include <config_cmd_default.h>
|
|
||||||
|
|
||||||
#define CONFIG_CMD_ELF
|
|
||||||
#define CONFIG_CMD_CACHE
|
|
||||||
#define CONFIG_CMD_JFFS2
|
|
||||||
#define CONFIG_CMD_EEPROM
|
|
||||||
#define CONFIG_CMD_DATE
|
|
||||||
|
|
||||||
#if (CONFIG_DRIVER_SMC91111)
|
|
||||||
#define CONFIG_CMD_PING
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if (CONFIG_SOFT_I2C)
|
|
||||||
#define CONFIG_CMD_I2C
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_CMD_DHCP
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Console settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_BAUDRATE 57600
|
|
||||||
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
||||||
|
|
||||||
#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
|
|
||||||
|
|
||||||
#if defined(CONFIG_CMD_KGDB)
|
|
||||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
||||||
#else
|
|
||||||
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
||||||
#endif
|
|
||||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
||||||
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
||||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
||||||
|
|
||||||
#define CONFIG_LOADS_ECHO 1
|
|
||||||
|
|
||||||
/*
|
|
||||||
* I2C settings
|
|
||||||
* By default PF2 is used as SDA and PF3 as SCL on the Stamp board
|
* By default PF2 is used as SDA and PF3 as SCL on the Stamp board
|
||||||
*/
|
*/
|
||||||
#if (CONFIG_SOFT_I2C)
|
#define CONFIG_SOFT_I2C
|
||||||
|
#ifdef CONFIG_SOFT_I2C
|
||||||
#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
|
#define PF_SCL PF3
|
||||||
#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
|
#define PF_SDA PF2
|
||||||
#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
|
#define I2C_INIT \
|
||||||
#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
|
do { \
|
||||||
#define I2C_SDA(bit) if(bit) { \
|
*pFIO_DIR |= PF_SCL; \
|
||||||
*pFIO_FLAG_S = PF_SDA; \
|
SSYNC(); \
|
||||||
asm("ssync;"); \
|
} while (0)
|
||||||
} \
|
#define I2C_ACTIVE \
|
||||||
else { \
|
do { \
|
||||||
*pFIO_FLAG_C = PF_SDA; \
|
*pFIO_DIR |= PF_SDA; \
|
||||||
asm("ssync;"); \
|
*pFIO_INEN &= ~PF_SDA; \
|
||||||
}
|
SSYNC(); \
|
||||||
#define I2C_SCL(bit) if(bit) { \
|
} while (0)
|
||||||
*pFIO_FLAG_S = PF_SCL; \
|
#define I2C_TRISTATE \
|
||||||
asm("ssync;"); \
|
do { \
|
||||||
} \
|
*pFIO_DIR &= ~PF_SDA; \
|
||||||
else { \
|
*pFIO_INEN |= PF_SDA; \
|
||||||
*pFIO_FLAG_C = PF_SCL; \
|
SSYNC(); \
|
||||||
asm("ssync;"); \
|
} while (0)
|
||||||
}
|
#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
|
||||||
|
#define I2C_SDA(bit) \
|
||||||
|
do { \
|
||||||
|
if (bit) \
|
||||||
|
*pFIO_FLAG_S = PF_SDA; \
|
||||||
|
else \
|
||||||
|
*pFIO_FLAG_C = PF_SDA; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_SCL(bit) \
|
||||||
|
do { \
|
||||||
|
if (bit) \
|
||||||
|
*pFIO_FLAG_S = PF_SCL; \
|
||||||
|
else \
|
||||||
|
*pFIO_FLAG_C = PF_SCL; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
||||||
|
|
||||||
#define CONFIG_SYS_I2C_SPEED 50000
|
#define CONFIG_SYS_I2C_SPEED 50000
|
||||||
#define CONFIG_SYS_I2C_SLAVE 0
|
#define CONFIG_SYS_I2C_SLAVE 0
|
||||||
#endif /* CONFIG_SOFT_I2C */
|
#endif
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Compact Flash settings
|
* Compact Flash / IDE / ATA Settings
|
||||||
*/
|
*/
|
||||||
|
|
||||||
/* Enabled below option for CF support */
|
/* Enabled below option for CF support */
|
||||||
/* #define CONFIG_STAMP_CF 1 */
|
/* #define CONFIG_STAMP_CF */
|
||||||
|
#if defined(CONFIG_STAMP_CF)
|
||||||
#if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE)
|
#define CONFIG_MISC_INIT_R
|
||||||
|
|
||||||
#define CONFIG_MISC_INIT_R 1
|
|
||||||
#define CONFIG_DOS_PARTITION 1
|
#define CONFIG_DOS_PARTITION 1
|
||||||
/*
|
|
||||||
* IDE/ATA stuff
|
|
||||||
*/
|
|
||||||
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
|
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
|
||||||
#undef CONFIG_IDE_LED /* no led for ide supported */
|
#undef CONFIG_IDE_LED /* no led for ide supported */
|
||||||
#undef CONFIG_IDE_RESET /* no reset for ide supported */
|
#undef CONFIG_IDE_RESET /* no reset for ide supported */
|
||||||
|
|
||||||
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
|
#define CONFIG_SYS_IDE_MAXBUS 1
|
||||||
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
|
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
|
||||||
|
|
||||||
#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000
|
#define CONFIG_SYS_ATA_BASE_ADDR 0x20200000
|
||||||
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
||||||
|
|
||||||
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
|
||||||
#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
|
#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
|
||||||
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0007 /* alternate registers */
|
||||||
|
|
||||||
#define CONFIG_SYS_ATA_STRIDE 2
|
#define CONFIG_SYS_ATA_STRIDE 2
|
||||||
|
|
||||||
|
#undef CONFIG_EBIU_AMBCTL1_VAL
|
||||||
|
#define CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Miscellaneous configurable options
|
* Misc Settings
|
||||||
*/
|
*/
|
||||||
|
#define CONFIG_RTC_BFIN
|
||||||
|
#define CONFIG_UART_CONSOLE 0
|
||||||
|
|
||||||
#define CONFIG_SYS_HZ 1000 /* 1ms time tick */
|
/* FLASH/ETHERNET uses the same async bank */
|
||||||
|
#define SHARED_RESOURCES 1
|
||||||
|
|
||||||
#define CONFIG_SYS_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */
|
/* define to enable splash screen support */
|
||||||
|
/* #define CONFIG_VIDEO */
|
||||||
|
|
||||||
#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
|
|
||||||
|
|
||||||
#define CONFIG_SPI
|
|
||||||
|
|
||||||
#ifdef CONFIG_VIDEO
|
|
||||||
#if (CONFIG_VIDEO)
|
|
||||||
#define CONFIG_SPLASH_SCREEN 1
|
|
||||||
#define CONFIG_SILENT_CONSOLE 1
|
|
||||||
#else
|
|
||||||
#undef CONFIG_VIDEO
|
|
||||||
#endif
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* FLASH organization and environment definitions
|
* Pull in common ADI header for remaining command/environment setup
|
||||||
*/
|
*/
|
||||||
|
#include <configs/bfin_adi_common.h>
|
||||||
#define CONFIG_EBIU_SDRRC_VAL 0x268
|
|
||||||
#define CONFIG_EBIU_SDGCTL_VAL 0x911109
|
|
||||||
#define CONFIG_EBIU_SDBCTL_VAL 0x37
|
|
||||||
|
|
||||||
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
|
|
||||||
#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
|
|
||||||
#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
|
|
||||||
#define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
|
|
||||||
|
|
||||||
#include <asm/blackfin-config-post.h>
|
#include <asm/blackfin-config-post.h>
|
||||||
|
|
||||||
|
|
|
||||||
|
|
@ -2,272 +2,144 @@
|
||||||
* U-boot - Configuration file for BF537 STAMP board
|
* U-boot - Configuration file for BF537 STAMP board
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#ifndef __CONFIG_BF537_H__
|
#ifndef __CONFIG_BF537_STAMP_H__
|
||||||
#define __CONFIG_BF537_H__
|
#define __CONFIG_BF537_STAMP_H__
|
||||||
|
|
||||||
#include <asm/blackfin-config-pre.h>
|
#include <asm/blackfin-config-pre.h>
|
||||||
|
|
||||||
#define CONFIG_SYS_LONGHELP 1
|
|
||||||
#define CONFIG_CMDLINE_EDITING 1
|
|
||||||
#define CONFIG_BAUDRATE 57600
|
|
||||||
/* Set default serial console for bf537 */
|
|
||||||
#define CONFIG_UART_CONSOLE 0
|
|
||||||
#define CONFIG_BOOTDELAY 5
|
|
||||||
/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
|
|
||||||
/*#define CONFIG_BF537_STAMP_LEDCMD 1*/
|
|
||||||
|
|
||||||
#define CONFIG_PANIC_HANG 1
|
|
||||||
|
|
||||||
#define CONFIG_BFIN_CPU bf537-0.2
|
|
||||||
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
|
||||||
|
|
||||||
#define CONFIG_BFIN_MAC
|
|
||||||
|
|
||||||
/* This sets the default state of the cache on U-Boot's boot */
|
|
||||||
#define CONFIG_ICACHE_ON
|
|
||||||
#define CONFIG_DCACHE_ON
|
|
||||||
|
|
||||||
/* Define if want to do post memory test */
|
|
||||||
#undef CONFIG_POST_TEST
|
|
||||||
|
|
||||||
#define CONFIG_RTC_BFIN 1
|
|
||||||
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
|
|
||||||
|
|
||||||
/* CONFIG_CLKIN_HZ is any value in Hz */
|
|
||||||
#define CONFIG_CLKIN_HZ 25000000
|
|
||||||
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
|
|
||||||
/* 1=CLKIN/2 */
|
|
||||||
#define CONFIG_CLKIN_HALF 0
|
|
||||||
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
|
|
||||||
/* 1=bypass PLL*/
|
|
||||||
#define CONFIG_PLL_BYPASS 0
|
|
||||||
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
|
|
||||||
/* Values can range from 1-64 */
|
|
||||||
#define CONFIG_VCO_MULT 20
|
|
||||||
/* CONFIG_CCLK_DIV controls what the core clock divider is */
|
|
||||||
/* Values can be 1, 2, 4, or 8 ONLY */
|
|
||||||
#define CONFIG_CCLK_DIV 1
|
|
||||||
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/
|
|
||||||
/* Values can range from 1-15 */
|
|
||||||
#define CONFIG_SCLK_DIV 5
|
|
||||||
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
|
|
||||||
/* Values can range from 2-65535 */
|
|
||||||
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
|
|
||||||
#define CONFIG_SPI_BAUD 2
|
|
||||||
#define CONFIG_SPI_BAUD_INITBLOCK 4
|
|
||||||
|
|
||||||
#if ( CONFIG_CLKIN_HALF == 0 )
|
|
||||||
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
|
|
||||||
#else
|
|
||||||
#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if (CONFIG_PLL_BYPASS == 0)
|
|
||||||
#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
|
|
||||||
#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
|
|
||||||
#else
|
|
||||||
#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
|
|
||||||
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
|
|
||||||
#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
|
|
||||||
#define CONFIG_MEM_MT48LC32M8A2_75 1
|
|
||||||
|
|
||||||
#define CONFIG_LOADS_ECHO 1
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* rarpb, bootp or dhcp commands will perform only a
|
* Processor Settings
|
||||||
* configuration lookup from the BOOTP/DHCP server
|
|
||||||
* but not try to load any image using TFTP
|
|
||||||
*/
|
*/
|
||||||
#define CONFIG_SYS_AUTOLOAD "no"
|
#define CONFIG_BFIN_CPU bf537-0.2
|
||||||
|
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Clock Settings
|
||||||
|
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
|
||||||
|
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
|
||||||
|
*/
|
||||||
|
/* CONFIG_CLKIN_HZ is any value in Hz */
|
||||||
|
#define CONFIG_CLKIN_HZ 25000000
|
||||||
|
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
|
||||||
|
/* 1 = CLKIN / 2 */
|
||||||
|
#define CONFIG_CLKIN_HALF 0
|
||||||
|
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
|
||||||
|
/* 1 = bypass PLL */
|
||||||
|
#define CONFIG_PLL_BYPASS 0
|
||||||
|
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
|
||||||
|
/* Values can range from 0-63 (where 0 means 64) */
|
||||||
|
#define CONFIG_VCO_MULT 20
|
||||||
|
/* CCLK_DIV controls the core clock divider */
|
||||||
|
/* Values can be 1, 2, 4, or 8 ONLY */
|
||||||
|
#define CONFIG_CCLK_DIV 1
|
||||||
|
/* SCLK_DIV controls the system clock divider */
|
||||||
|
/* Values can range from 1-15 */
|
||||||
|
#define CONFIG_SCLK_DIV 5
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Memory Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_MEM_ADD_WDTH 10
|
||||||
|
#define CONFIG_MEM_SIZE 64
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_SDRRC_VAL 0x306
|
||||||
|
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
|
||||||
|
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
|
||||||
|
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
|
||||||
|
|
||||||
|
#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
|
||||||
|
#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Network Settings
|
* Network Settings
|
||||||
*/
|
*/
|
||||||
/* network support */
|
#ifndef __ADSPBF534__
|
||||||
#ifdef CONFIG_BFIN_MAC
|
#define ADI_CMDS_NETWORK 1
|
||||||
#define CONFIG_IPADDR 192.168.0.15
|
#define CONFIG_BFIN_MAC
|
||||||
#define CONFIG_NETMASK 255.255.255.0
|
|
||||||
#define CONFIG_GATEWAYIP 192.168.0.1
|
|
||||||
#define CONFIG_SERVERIP 192.168.0.2
|
|
||||||
#define CONFIG_HOSTNAME BF537
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_ROOTPATH /romfs
|
|
||||||
/* Uncomment next line to use fixed MAC address */
|
|
||||||
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
|
|
||||||
/* This is the routine that copies the MAC in Flash to the 'ethaddr' setting */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_LONGHELP 1
|
|
||||||
#define CONFIG_BOOTDELAY 5
|
|
||||||
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
|
|
||||||
#define CONFIG_BOOTCOMMAND "run ramboot"
|
|
||||||
|
|
||||||
#if defined(CONFIG_POST_TEST)
|
|
||||||
/* POST support */
|
|
||||||
#define CONFIG_POST ( CONFIG_SYS_POST_MEMORY | \
|
|
||||||
CONFIG_SYS_POST_UART | \
|
|
||||||
CONFIG_SYS_POST_FLASH | \
|
|
||||||
CONFIG_SYS_POST_ETHER | \
|
|
||||||
CONFIG_SYS_POST_LED | \
|
|
||||||
CONFIG_SYS_POST_BUTTON)
|
|
||||||
#else
|
|
||||||
#undef CONFIG_POST
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#ifdef CONFIG_POST
|
|
||||||
#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
|
|
||||||
#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/* CF-CARD IDE-HDD Support */
|
|
||||||
|
|
||||||
/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */
|
|
||||||
/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */
|
|
||||||
/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */
|
|
||||||
|
|
||||||
#if defined(CONFIG_BFIN_CF_IDE) || defined(CONFIG_BFIN_HDD_IDE) || defined(CONFIG_BFIN_TRUE_IDE)
|
|
||||||
# define CONFIG_BFIN_IDE 1
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*#define CONFIG_BF537_NAND */ /* Add nand flash support */
|
|
||||||
|
|
||||||
#define CONFIG_NETCONSOLE 1
|
#define CONFIG_NETCONSOLE 1
|
||||||
#define CONFIG_NET_MULTI 1
|
#define CONFIG_NET_MULTI 1
|
||||||
|
#endif
|
||||||
/*
|
#define CONFIG_HOSTNAME bf537-stamp
|
||||||
* BOOTP options
|
/* Uncomment next line to use fixed MAC address */
|
||||||
*/
|
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
|
||||||
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
||||||
#define CONFIG_BOOTP_BOOTPATH
|
|
||||||
#define CONFIG_BOOTP_GATEWAY
|
|
||||||
#define CONFIG_BOOTP_HOSTNAME
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Command line configuration.
|
* Flash Settings
|
||||||
*/
|
*/
|
||||||
#include <config_cmd_default.h>
|
#define CONFIG_FLASH_CFI_DRIVER
|
||||||
|
|
||||||
#define CONFIG_CMD_ELF
|
|
||||||
#define CONFIG_CMD_I2C
|
|
||||||
#define CONFIG_CMD_CACHE
|
|
||||||
#define CONFIG_CMD_JFFS2
|
|
||||||
#define CONFIG_CMD_EEPROM
|
|
||||||
#define CONFIG_CMD_DATE
|
|
||||||
|
|
||||||
#ifndef CONFIG_BFIN_MAC
|
|
||||||
#undef CONFIG_CMD_NET
|
|
||||||
#else
|
|
||||||
#define CONFIG_CMD_PING
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#if defined(CONFIG_BFIN_CF_IDE) \
|
|
||||||
|| defined(CONFIG_BFIN_HDD_IDE) \
|
|
||||||
|| defined(CONFIG_BFIN_TRUE_IDE)
|
|
||||||
#define CONFIG_CMD_IDE
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_CMD_DHCP
|
|
||||||
|
|
||||||
#if defined(CONFIG_POST)
|
|
||||||
#define CONFIG_CMD_DIAG
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#ifdef CONFIG_BF537_NAND
|
|
||||||
#define CONFIG_CMD_NAND
|
|
||||||
#endif
|
|
||||||
|
|
||||||
|
|
||||||
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
|
|
||||||
#define CONFIG_LOADADDR 0x1000000
|
|
||||||
|
|
||||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
||||||
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
|
|
||||||
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
||||||
"nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
|
|
||||||
"addip=setenv bootargs $(bootargs) " \
|
|
||||||
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
|
|
||||||
":$(hostname):eth0:off\0" \
|
|
||||||
"ramboot=tftpboot $(loadaddr) linux;" \
|
|
||||||
"run ramargs;run addip;bootelf\0" \
|
|
||||||
"nfsboot=tftpboot $(loadaddr) linux;" \
|
|
||||||
"run nfsargs;run addip;bootelf\0" \
|
|
||||||
"flashboot=bootm 0x20100000\0" \
|
|
||||||
"update=tftpboot $(loadaddr) u-boot.bin;" \
|
|
||||||
"protect off 0x20000000 0x2007FFFF;" \
|
|
||||||
"erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \
|
|
||||||
""
|
|
||||||
|
|
||||||
#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
|
|
||||||
|
|
||||||
#if defined(CONFIG_CMD_KGDB)
|
|
||||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
||||||
#else
|
|
||||||
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
||||||
#endif
|
|
||||||
#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024*1024)
|
|
||||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
||||||
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
||||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
||||||
#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */
|
|
||||||
#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
|
|
||||||
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR /* default load address */
|
|
||||||
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
|
|
||||||
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
||||||
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
||||||
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
#define CONFIG_SYS_FLASH_CFI
|
||||||
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
|
||||||
#define CONFIG_SYS_FLASH_PROTECTION
|
#define CONFIG_SYS_FLASH_PROTECTION
|
||||||
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
||||||
#define CONFIG_SYS_MAX_FLASH_SECT 71 /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
|
/* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */
|
||||||
|
#define CONFIG_SYS_MAX_FLASH_SECT 71
|
||||||
|
|
||||||
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
||||||
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
|
|
||||||
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
||||||
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
|
|
||||||
#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
|
|
||||||
#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
|
|
||||||
#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* SPI Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_BFIN_SPI
|
||||||
|
#define CONFIG_ENV_SPI_MAX_HZ 30000000
|
||||||
|
#define CONFIG_SF_DEFAULT_HZ 30000000
|
||||||
|
#define CONFIG_SPI_FLASH
|
||||||
|
#define CONFIG_SPI_FLASH_ATMEL
|
||||||
|
#define CONFIG_SPI_FLASH_SPANSION
|
||||||
|
#define CONFIG_SPI_FLASH_STMICRO
|
||||||
|
#define CONFIG_SPI_FLASH_WINBOND
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Env Storage Settings
|
||||||
|
*/
|
||||||
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
|
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
|
||||||
#define CONFIG_ENV_IS_IN_EEPROM 1
|
#define CONFIG_ENV_IS_IN_SPI_FLASH
|
||||||
#define CONFIG_ENV_OFFSET 0x4000
|
#define CONFIG_ENV_OFFSET 0x4000
|
||||||
#define CONFIG_ENV_HEADER (CONFIG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
|
|
||||||
#else
|
|
||||||
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
||||||
#define CONFIG_ENV_ADDR 0x20004000
|
|
||||||
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
|
|
||||||
#endif
|
|
||||||
#define CONFIG_ENV_SIZE 0x2000
|
#define CONFIG_ENV_SIZE 0x2000
|
||||||
#define CONFIG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
|
#define CONFIG_ENV_SECT_SIZE 0x2000
|
||||||
|
#else
|
||||||
|
#define CONFIG_ENV_IS_IN_FLASH
|
||||||
|
#define CONFIG_ENV_OFFSET 0x4000
|
||||||
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
|
||||||
|
#define CONFIG_ENV_SIZE 0x2000
|
||||||
|
#define CONFIG_ENV_SECT_SIZE 0x2000
|
||||||
|
#endif
|
||||||
|
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
|
||||||
#define ENV_IS_EMBEDDED
|
#define ENV_IS_EMBEDDED
|
||||||
|
#else
|
||||||
|
#define ENV_IS_EMBEDDED_CUSTOM
|
||||||
|
#endif
|
||||||
|
|
||||||
/* JFFS Partition offset set */
|
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
|
|
||||||
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
|
|
||||||
/* 512k reserved for u-boot */
|
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 15
|
|
||||||
|
|
||||||
#define CONFIG_SPI
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Stack sizes
|
* I2C Settings
|
||||||
*/
|
*/
|
||||||
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
|
#define CONFIG_BFIN_TWI_I2C 1
|
||||||
|
#define CONFIG_HARD_I2C 1
|
||||||
|
#define CONFIG_SYS_I2C_SPEED 50000
|
||||||
|
#define CONFIG_SYS_I2C_SLAVE 0
|
||||||
|
|
||||||
#define POLL_MODE 1
|
|
||||||
#define FLASH_TOT_SECT 71
|
|
||||||
#define FLASH_SIZE 0x400000
|
|
||||||
#define CONFIG_SYS_FLASH_SIZE 0x400000
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Board NAND Infomation
|
* SPI_MMC Settings
|
||||||
*/
|
*/
|
||||||
|
#define CONFIG_MMC
|
||||||
|
#define CONFIG_BFIN_SPI_MMC
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* NAND Settings
|
||||||
|
*/
|
||||||
|
/* #define CONFIG_BF537_NAND */
|
||||||
|
#ifdef CONFIG_BF537_NAND
|
||||||
|
# define CONFIG_CMD_NAND
|
||||||
|
#endif
|
||||||
|
|
||||||
#define CONFIG_SYS_NAND_ADDR 0x20212000
|
#define CONFIG_SYS_NAND_ADDR 0x20212000
|
||||||
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_NAND_ADDR
|
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_NAND_ADDR
|
||||||
|
|
@ -280,56 +152,35 @@
|
||||||
#define NAND_MAX_FLOORS 1
|
#define NAND_MAX_FLOORS 1
|
||||||
#define BFIN_NAND_READY PF3
|
#define BFIN_NAND_READY PF3
|
||||||
|
|
||||||
#define NAND_WAIT_READY(nand) \
|
#define NAND_WAIT_READY(nand) \
|
||||||
do { \
|
do { \
|
||||||
int timeout = 0; \
|
int timeout = 0; \
|
||||||
while(!(*pPORTFIO & PF3)) \
|
while (!(*pPORTFIO & PF3)) \
|
||||||
if (timeout++ > 100000) \
|
if (timeout++ > 100000) \
|
||||||
break; \
|
break; \
|
||||||
} while (0)
|
} while (0)
|
||||||
|
|
||||||
#define BFIN_NAND_CLE (1<<2) /* A2 -> Command Enable */
|
#define BFIN_NAND_CLE (1 << 2) /* A2 -> Command Enable */
|
||||||
#define BFIN_NAND_ALE (1<<1) /* A1 -> Address Enable */
|
#define BFIN_NAND_ALE (1 << 1) /* A1 -> Address Enable */
|
||||||
|
#define WRITE_NAND_COMMAND(d, adr) bfin_write8(adr | BFIN_NAND_CLE, d)
|
||||||
|
#define WRITE_NAND_ADDRESS(d, adr) bfin_write8(adr | BFIN_NAND_ALE, d)
|
||||||
|
#define WRITE_NAND(d, adr) bfin_write8(adr, d)
|
||||||
|
#define READ_NAND(adr) bfin_read8(adr)
|
||||||
|
|
||||||
#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_CLE) = (__u8)(d); } while(0)
|
|
||||||
#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr | BFIN_NAND_ALE) = (__u8)(d); } while(0)
|
|
||||||
#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
|
|
||||||
#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Initialize PSD4256 registers for using I2C
|
* CF-CARD IDE-HDD Support
|
||||||
*/
|
*/
|
||||||
#define CONFIG_MISC_INIT_R
|
/* #define CONFIG_BFIN_TRUE_IDE */ /* Add CF flash card support */
|
||||||
|
/* #define CONFIG_BFIN_CF_IDE */ /* Add CF flash card support */
|
||||||
|
/* #define CONFIG_BFIN_HDD_IDE */ /* Add IDE Disk Drive (HDD) support */
|
||||||
|
|
||||||
#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
|
#if defined(CONFIG_BFIN_CF_IDE) || \
|
||||||
|
defined(CONFIG_BFIN_HDD_IDE) || \
|
||||||
/*
|
defined(CONFIG_BFIN_TRUE_IDE)
|
||||||
* I2C settings
|
# define CONFIG_BFIN_IDE 1
|
||||||
*/
|
# define CONFIG_CMD_IDE
|
||||||
#define CONFIG_HARD_I2C 1
|
#endif
|
||||||
#define CONFIG_BFIN_TWI_I2C 1
|
|
||||||
#define CONFIG_SYS_I2C_SPEED 50000
|
|
||||||
#define CONFIG_SYS_I2C_SLAVE 0
|
|
||||||
|
|
||||||
#define CONFIG_EBIU_SDRRC_VAL 0x306
|
|
||||||
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
|
|
||||||
#define CONFIG_EBIU_SDBCTL_VAL 0x25
|
|
||||||
|
|
||||||
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
|
|
||||||
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
|
|
||||||
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
|
|
||||||
|
|
||||||
/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
|
|
||||||
/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
|
|
||||||
#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
|
|
||||||
~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
|
|
||||||
#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
|
|
||||||
B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define AMGCTLVAL 0xFF
|
|
||||||
#define AMBCTL0VAL 0x7BB07BB0
|
|
||||||
#define AMBCTL1VAL 0xFFC27BB0
|
|
||||||
|
|
||||||
#if defined(CONFIG_BFIN_IDE)
|
#if defined(CONFIG_BFIN_IDE)
|
||||||
|
|
||||||
|
|
@ -341,11 +192,11 @@
|
||||||
#undef CONFIG_IDE_LED /* no led for ide supported */
|
#undef CONFIG_IDE_LED /* no led for ide supported */
|
||||||
#undef CONFIG_IDE_RESET /* no reset for ide supported */
|
#undef CONFIG_IDE_RESET /* no reset for ide supported */
|
||||||
|
|
||||||
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
|
#define CONFIG_SYS_IDE_MAXBUS 1
|
||||||
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
|
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1)
|
||||||
|
|
||||||
#undef AMBCTL1VAL
|
#undef CONFIG_EBIU_AMBCTL1_VAL
|
||||||
#define AMBCTL1VAL 0xFFC3FFC3
|
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3
|
||||||
|
|
||||||
#define CONFIG_CF_ATASEL_DIS 0x20311800
|
#define CONFIG_CF_ATASEL_DIS 0x20311800
|
||||||
#define CONFIG_CF_ATASEL_ENA 0x20311802
|
#define CONFIG_CF_ATASEL_ENA 0x20311802
|
||||||
|
|
@ -357,34 +208,54 @@
|
||||||
*/
|
*/
|
||||||
#define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000
|
#define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000
|
||||||
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
||||||
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
|
||||||
#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
|
#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
|
||||||
#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */
|
||||||
#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */
|
#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.Ax */
|
||||||
#endif /* CONFIG_BFIN_TRUE_IDE */
|
|
||||||
|
|
||||||
#if defined(CONFIG_BFIN_CF_IDE) /* USE CompactFlash Storage Card in the common memory space */
|
#elif defined(CONFIG_BFIN_CF_IDE)
|
||||||
#define CONFIG_SYS_ATA_BASE_ADDR 0x20211800
|
#define CONFIG_SYS_ATA_BASE_ADDR 0x20211800
|
||||||
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
||||||
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */
|
||||||
#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
|
#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */
|
||||||
#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* Offset for alternate registers */
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */
|
||||||
#define CONFIG_SYS_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */
|
#define CONFIG_SYS_ATA_STRIDE 1 /* CF.A0 --> Blackfin.Ax */
|
||||||
#endif /* CONFIG_BFIN_CF_IDE */
|
|
||||||
|
|
||||||
#if defined(CONFIG_BFIN_HDD_IDE) /* USE TRUE IDE */
|
#elif defined(CONFIG_BFIN_HDD_IDE)
|
||||||
#define CONFIG_SYS_ATA_BASE_ADDR 0x20314000
|
#define CONFIG_SYS_ATA_BASE_ADDR 0x20314000
|
||||||
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
||||||
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
|
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */
|
||||||
#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
|
#define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */
|
||||||
#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* Offset for alternate registers */
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */
|
||||||
#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */
|
#define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */
|
||||||
|
|
||||||
#undef CONFIG_SCLK_DIV
|
#undef CONFIG_SCLK_DIV
|
||||||
#define CONFIG_SCLK_DIV 8
|
#define CONFIG_SCLK_DIV 8
|
||||||
#endif /* CONFIG_BFIN_HDD_IDE */
|
#endif
|
||||||
|
|
||||||
#endif /*CONFIG_BFIN_IDE */
|
#endif
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Misc Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_MISC_INIT_R
|
||||||
|
#define CONFIG_RTC_BFIN
|
||||||
|
#define CONFIG_UART_CONSOLE 0
|
||||||
|
|
||||||
|
/* #define CONFIG_BF537_STAMP_LEDCMD 1 */
|
||||||
|
|
||||||
|
/* Define if want to do post memory test */
|
||||||
|
#undef CONFIG_POST
|
||||||
|
#ifdef CONFIG_POST
|
||||||
|
#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
|
||||||
|
#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
|
||||||
|
#endif
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Pull in common ADI header for remaining command/environment setup
|
||||||
|
*/
|
||||||
|
#include <configs/bfin_adi_common.h>
|
||||||
|
|
||||||
#include <asm/blackfin-config-post.h>
|
#include <asm/blackfin-config-post.h>
|
||||||
|
|
||||||
|
|
|
||||||
|
|
@ -2,229 +2,152 @@
|
||||||
* U-boot - Configuration file for BF561 EZKIT board
|
* U-boot - Configuration file for BF561 EZKIT board
|
||||||
*/
|
*/
|
||||||
|
|
||||||
#ifndef __CONFIG_EZKIT561_H__
|
#ifndef __CONFIG_BF561_EZKIT_H__
|
||||||
#define __CONFIG_EZKIT561_H__
|
#define __CONFIG_BF561_EZKIT_H__
|
||||||
|
|
||||||
#include <asm/blackfin-config-pre.h>
|
#include <asm/blackfin-config-pre.h>
|
||||||
|
|
||||||
#define CONFIG_SYS_LONGHELP 1
|
|
||||||
#define CONFIG_CMDLINE_EDITING 1
|
|
||||||
#define CONFIG_BAUDRATE 57600
|
|
||||||
/* Set default serial console for bf537 */
|
|
||||||
#define CONFIG_UART_CONSOLE 0
|
|
||||||
#define CONFIG_EZKIT561 1
|
|
||||||
#define CONFIG_BOOTDELAY 5
|
|
||||||
|
|
||||||
#define CONFIG_PANIC_HANG 1
|
|
||||||
|
|
||||||
#define CONFIG_BFIN_CPU bf561-0.3
|
|
||||||
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
|
||||||
|
|
||||||
/* This sets the default state of the cache on U-Boot's boot */
|
|
||||||
#define CONFIG_ICACHE_ON
|
|
||||||
#define CONFIG_DCACHE_ON
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Board settings
|
* Processor Settings
|
||||||
*/
|
*/
|
||||||
|
#define CONFIG_BFIN_CPU bf561-0.3
|
||||||
|
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Clock Settings
|
||||||
|
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
|
||||||
|
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
|
||||||
|
*/
|
||||||
|
/* CONFIG_CLKIN_HZ is any value in Hz */
|
||||||
|
#define CONFIG_CLKIN_HZ 30000000
|
||||||
|
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
|
||||||
|
/* 1 = CLKIN / 2 */
|
||||||
|
#define CONFIG_CLKIN_HALF 0
|
||||||
|
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
|
||||||
|
/* 1 = bypass PLL */
|
||||||
|
#define CONFIG_PLL_BYPASS 0
|
||||||
|
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
|
||||||
|
/* Values can range from 0-63 (where 0 means 64) */
|
||||||
|
#define CONFIG_VCO_MULT 20
|
||||||
|
/* CCLK_DIV controls the core clock divider */
|
||||||
|
/* Values can be 1, 2, 4, or 8 ONLY */
|
||||||
|
#define CONFIG_CCLK_DIV 1
|
||||||
|
/* SCLK_DIV controls the system clock divider */
|
||||||
|
/* Values can range from 1-15 */
|
||||||
|
#define CONFIG_SCLK_DIV 6
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Memory Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_MEM_ADD_WDTH 9
|
||||||
|
#define CONFIG_MEM_SIZE 64
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_SDRRC_VAL 0x306
|
||||||
|
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
|
||||||
|
|
||||||
|
#define CONFIG_EBIU_AMGCTL_VAL 0x3F
|
||||||
|
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
|
||||||
|
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
|
||||||
|
|
||||||
|
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
|
||||||
|
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
|
||||||
|
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Network Settings
|
||||||
|
*/
|
||||||
|
#define ADI_CMDS_NETWORK 1
|
||||||
#define CONFIG_DRIVER_SMC91111 1
|
#define CONFIG_DRIVER_SMC91111 1
|
||||||
#define CONFIG_SMC91111_BASE 0x2C010300
|
#define CONFIG_SMC91111_BASE 0x2C010300
|
||||||
#define CONFIG_ASYNC_EBIU_BASE CONFIG_SMC91111_BASE & ~(4*1024*1024)
|
|
||||||
#define CONFIG_SMC_USE_32_BIT 1
|
#define CONFIG_SMC_USE_32_BIT 1
|
||||||
#define CONFIG_MISC_INIT_R 1
|
#define CONFIG_HOSTNAME bf561-ezkit
|
||||||
|
/* Uncomment next line to use fixed MAC address */
|
||||||
|
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
|
||||||
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Clock settings
|
* Flash Settings
|
||||||
*/
|
*/
|
||||||
|
#define CONFIG_SYS_FLASH_CFI
|
||||||
/* CONFIG_CLKIN_HZ is any value in Hz */
|
#define CONFIG_FLASH_CFI_DRIVER
|
||||||
#define CONFIG_CLKIN_HZ 30000000
|
|
||||||
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
|
|
||||||
/* 1=CLKIN/2 */
|
|
||||||
#define CONFIG_CLKIN_HALF 0
|
|
||||||
/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
|
|
||||||
/* 1=bypass PLL */
|
|
||||||
#define CONFIG_PLL_BYPASS 0
|
|
||||||
/* CONFIG_VCO_MULT controls what the multiplier of the PLL is */
|
|
||||||
/* Values can range from 1-64 */
|
|
||||||
#define CONFIG_VCO_MULT 20
|
|
||||||
/* CONFIG_CCLK_DIV controls what the core clock divider is */
|
|
||||||
/* Values can be 1, 2, 4, or 8 ONLY */
|
|
||||||
#define CONFIG_CCLK_DIV 1
|
|
||||||
/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
|
|
||||||
/* Values can range from 1-15 */
|
|
||||||
#define CONFIG_SCLK_DIV 5
|
|
||||||
/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
|
|
||||||
/* Values can range from 2-65535 */
|
|
||||||
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
|
|
||||||
#define CONFIG_SPI_BAUD 2
|
|
||||||
#define CONFIG_SPI_BAUD_INITBLOCK 4
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Network settings
|
|
||||||
*/
|
|
||||||
#if (CONFIG_DRIVER_SMC91111)
|
|
||||||
#define CONFIG_IPADDR 192.168.0.15
|
|
||||||
#define CONFIG_NETMASK 255.255.255.0
|
|
||||||
#define CONFIG_GATEWAYIP 192.168.0.1
|
|
||||||
#define CONFIG_SERVERIP 192.168.0.2
|
|
||||||
#define CONFIG_HOSTNAME ezkit561
|
|
||||||
#define CONFIG_ROOTPATH /arm-cross-build/BF561/uClinux-dist/romfs
|
|
||||||
#endif /* CONFIG_DRIVER_SMC91111 */
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Flash settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
|
|
||||||
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
|
|
||||||
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
|
#define CONFIG_SYS_FLASH_CFI_AMD_RESET
|
||||||
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
||||||
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
#define CONFIG_SYS_FLASH_BASE 0x20000000
|
||||||
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1
|
||||||
#define CONFIG_SYS_MAX_FLASH_SECT 135 /* max number of sectors on one chip */
|
#define CONFIG_SYS_MAX_FLASH_SECT 135
|
||||||
#define CONFIG_ENV_ADDR 0x20020000
|
/* The BF561-EZKIT uses a top boot flash */
|
||||||
#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
||||||
/* JFFS Partition offset set */
|
#define CONFIG_ENV_ADDR 0x20004000
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
|
#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR - CONFIG_SYS_FLASH_BASE)
|
||||||
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
|
#define CONFIG_ENV_SIZE 0x2000
|
||||||
/* 512k reserved for u-boot */
|
#define CONFIG_ENV_SECT_SIZE 0x10000
|
||||||
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 8
|
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
|
||||||
|
#define ENV_IS_EMBEDDED
|
||||||
/*
|
|
||||||
* SDRAM settings & memory map
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
|
|
||||||
#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */
|
|
||||||
#define CONFIG_MEM_MT48LC16M16A2TG_75 1
|
|
||||||
|
|
||||||
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
||||||
#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MEMTEST_START 0x0 /* memtest works on */
|
|
||||||
#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024*1024) /* 1 ... 63 MB in DRAM */
|
|
||||||
|
|
||||||
#define CONFIG_LOADADDR 0x01000000 /* default load address */
|
|
||||||
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
|
|
||||||
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
|
|
||||||
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
||||||
#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
|
|
||||||
|
|
||||||
#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
|
|
||||||
#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
|
|
||||||
#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
|
|
||||||
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
|
|
||||||
|
|
||||||
#if ( CONFIG_CLKIN_HALF == 0 )
|
|
||||||
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
|
|
||||||
#else
|
#else
|
||||||
#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
|
#define ENV_IS_EMBEDDED_CUSTOM
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if (CONFIG_PLL_BYPASS == 0)
|
|
||||||
#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
|
/*
|
||||||
#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
|
* I2C Settings
|
||||||
#else
|
*/
|
||||||
#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
|
#define CONFIG_SOFT_I2C
|
||||||
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
|
#ifdef CONFIG_SOFT_I2C
|
||||||
|
#define PF_SCL PF0
|
||||||
|
#define PF_SDA PF1
|
||||||
|
#define I2C_INIT \
|
||||||
|
do { \
|
||||||
|
*pFIO0_DIR |= PF_SCL; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_ACTIVE \
|
||||||
|
do { \
|
||||||
|
*pFIO0_DIR |= PF_SDA; \
|
||||||
|
*pFIO0_INEN &= ~PF_SDA; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_TRISTATE \
|
||||||
|
do { \
|
||||||
|
*pFIO0_DIR &= ~PF_SDA; \
|
||||||
|
*pFIO0_INEN |= PF_SDA; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_READ ((*pFIO0_FLAG_D & PF_SDA) != 0)
|
||||||
|
#define I2C_SDA(bit) \
|
||||||
|
do { \
|
||||||
|
if (bit) \
|
||||||
|
*pFIO0_FLAG_S = PF_SDA; \
|
||||||
|
else \
|
||||||
|
*pFIO0_FLAG_C = PF_SDA; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_SCL(bit) \
|
||||||
|
do { \
|
||||||
|
if (bit) \
|
||||||
|
*pFIO0_FLAG_S = PF_SCL; \
|
||||||
|
else \
|
||||||
|
*pFIO0_FLAG_C = PF_SCL; \
|
||||||
|
SSYNC(); \
|
||||||
|
} while (0)
|
||||||
|
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
|
||||||
|
|
||||||
|
#define CONFIG_SYS_I2C_SPEED 50000
|
||||||
|
#define CONFIG_SYS_I2C_SLAVE 0
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/*
|
|
||||||
* Command settings
|
|
||||||
*/
|
|
||||||
|
|
||||||
#define CONFIG_SYS_AUTOLOAD "no" /* rarpb, bootp, dhcp commands will */
|
|
||||||
/* only perform a configuration */
|
|
||||||
/* lookup from the BOOTP/DHCP server */
|
|
||||||
/* but not try to load any image */
|
|
||||||
/* using TFTP */
|
|
||||||
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, */
|
|
||||||
/* currently its disabled */
|
|
||||||
#define CONFIG_BOOTCOMMAND "run ramboot"
|
|
||||||
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
|
|
||||||
|
|
||||||
#if (CONFIG_DRIVER_SMC91111)
|
|
||||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
||||||
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
|
|
||||||
"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
|
|
||||||
"$(rootpath) console=ttyBF0,57600\0" \
|
|
||||||
"addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
|
|
||||||
"$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
|
|
||||||
"ramboot=tftpboot $(loadaddr) linux; " \
|
|
||||||
"run ramargs; run addip; bootelf\0" \
|
|
||||||
"nfsboot=tftpboot $(loadaddr) linux; " \
|
|
||||||
"run nfsargs; run addip; bootelf\0" \
|
|
||||||
"update=tftpboot $(loadaddr) u-boot.bin; " \
|
|
||||||
"protect off 0x20000000 0x2003FFFF; " \
|
|
||||||
"erase 0x20000000 0x2003FFFF; " \
|
|
||||||
"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
|
|
||||||
""
|
|
||||||
#else
|
|
||||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
||||||
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
|
|
||||||
"flashboot=bootm 0x20100000\0" \
|
|
||||||
""
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* BOOTP options
|
* Misc Settings
|
||||||
*/
|
*/
|
||||||
#define CONFIG_BOOTP_BOOTFILESIZE
|
#define CONFIG_UART_CONSOLE 0
|
||||||
#define CONFIG_BOOTP_BOOTPATH
|
|
||||||
#define CONFIG_BOOTP_GATEWAY
|
|
||||||
#define CONFIG_BOOTP_HOSTNAME
|
|
||||||
|
|
||||||
/*
|
/*
|
||||||
* Command line configuration.
|
* Pull in common ADI header for remaining command/environment setup
|
||||||
*/
|
*/
|
||||||
#include <config_cmd_default.h>
|
#include <configs/bfin_adi_common.h>
|
||||||
|
|
||||||
#define CONFIG_CMD_ELF
|
|
||||||
#define CONFIG_CMD_CACHE
|
|
||||||
#define CONFIG_CMD_JFFS2
|
|
||||||
|
|
||||||
#if defined(CONFIG_DRIVER_SMC91111)
|
|
||||||
#define CONFIG_CMD_PING
|
|
||||||
#define CONFIG_CMD_DHCP
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Console settings
|
|
||||||
*/
|
|
||||||
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
|
|
||||||
|
|
||||||
#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
|
|
||||||
|
|
||||||
#if defined(CONFIG_CMD_KGDB)
|
|
||||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
||||||
#else
|
|
||||||
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
||||||
#endif
|
|
||||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
||||||
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
||||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
||||||
|
|
||||||
#define CONFIG_LOADS_ECHO 1
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Miscellaneous configurable options
|
|
||||||
*/
|
|
||||||
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
|
|
||||||
#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
|
|
||||||
|
|
||||||
/*
|
|
||||||
* FLASH organization and environment definitions
|
|
||||||
*/
|
|
||||||
#define CONFIG_EBIU_SDRRC_VAL 0x306
|
|
||||||
#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
|
|
||||||
#define CONFIG_EBIU_SDBCTL_VAL 0x15
|
|
||||||
|
|
||||||
#define CONFIG_EBIU_AMGCTL_VAL 0x3F
|
|
||||||
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
|
|
||||||
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
|
|
||||||
|
|
||||||
#include <asm/blackfin-config-post.h>
|
#include <asm/blackfin-config-post.h>
|
||||||
|
|
||||||
|
|
|
||||||
|
|
@ -0,0 +1,198 @@
|
||||||
|
/*
|
||||||
|
* U-Boot - Common settings for Analog Devices boards
|
||||||
|
*/
|
||||||
|
|
||||||
|
#ifndef __CONFIG_BFIN_ADI_COMMON_H__
|
||||||
|
#define __CONFIG_BFIN_ADI_COMMON_H__
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Command Settings
|
||||||
|
*/
|
||||||
|
#ifndef _CONFIG_CMD_DEFAULT_H
|
||||||
|
# include <config_cmd_default.h>
|
||||||
|
# if ADI_CMDS_NETWORK
|
||||||
|
# define CONFIG_CMD_DHCP
|
||||||
|
# define CONFIG_CMD_PING
|
||||||
|
# ifdef CONFIG_BFIN_MAC
|
||||||
|
# define CONFIG_CMD_MII
|
||||||
|
# endif
|
||||||
|
# else
|
||||||
|
# undef CONFIG_CMD_BOOTD
|
||||||
|
# undef CONFIG_CMD_NET
|
||||||
|
# undef CONFIG_CMD_NFS
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_LIBATA
|
||||||
|
# define CONFIG_CMD_FAT
|
||||||
|
# define CONFIG_CMD_SATA
|
||||||
|
# define CONFIG_DOS_PARTITION
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_MMC
|
||||||
|
# define CONFIG_CMD_FAT
|
||||||
|
# define CONFIG_CMD_MMC
|
||||||
|
# define CONFIG_DOS_PARTITION
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_USB
|
||||||
|
# define CONFIG_CMD_EXT2
|
||||||
|
# define CONFIG_CMD_FAT
|
||||||
|
# define CONFIG_CMD_USB
|
||||||
|
# define CONFIG_CMD_USB_STORAGE
|
||||||
|
# define CONFIG_DOS_PARTITION
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_POST
|
||||||
|
# define CONFIG_CMD_DIAG
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_RTC_BFIN
|
||||||
|
# define CONFIG_CMD_DATE
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_SPI
|
||||||
|
# define CONFIG_CMD_EEPROM
|
||||||
|
# endif
|
||||||
|
# if defined(CONFIG_BFIN_SPI) || defined(CONFIG_SOFT_SPI)
|
||||||
|
# define CONFIG_CMD_SPI
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_SPI_FLASH
|
||||||
|
# define CONFIG_CMD_SF
|
||||||
|
# endif
|
||||||
|
# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
|
||||||
|
# define CONFIG_CMD_I2C
|
||||||
|
# endif
|
||||||
|
# ifdef CONFIG_SYS_NO_FLASH
|
||||||
|
# undef CONFIG_CMD_FLASH
|
||||||
|
# undef CONFIG_CMD_IMLS
|
||||||
|
# else
|
||||||
|
# define CONFIG_CMD_JFFS2
|
||||||
|
# endif
|
||||||
|
# define CONFIG_CMD_BOOTLDR
|
||||||
|
# define CONFIG_CMD_CACHE
|
||||||
|
# define CONFIG_CMD_CPLBINFO
|
||||||
|
# define CONFIG_CMD_ELF
|
||||||
|
# define CONFIG_ELF_SIMPLE_LOAD
|
||||||
|
# define CONFIG_CMD_REGINFO
|
||||||
|
# define CONFIG_CMD_STRINGS
|
||||||
|
# if defined(__ADSPBF51x__) || defined(__ADSPBF52x__) || defined(__ADSPBF54x__)
|
||||||
|
# define CONFIG_CMD_OTP
|
||||||
|
# endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Console Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_SYS_LONGHELP 1
|
||||||
|
#define CONFIG_CMDLINE_EDITING 1
|
||||||
|
#define CONFIG_AUTO_COMPLETE 1
|
||||||
|
#define CONFIG_LOADS_ECHO 1
|
||||||
|
#define CONFIG_JTAG_CONSOLE
|
||||||
|
#ifndef CONFIG_BAUDRATE
|
||||||
|
# define CONFIG_BAUDRATE 57600
|
||||||
|
#endif
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Debug Settings
|
||||||
|
*/
|
||||||
|
#define CONFIG_ENV_OVERWRITE 1
|
||||||
|
#define CONFIG_DEBUG_DUMP 1
|
||||||
|
#define CONFIG_DEBUG_DUMP_SYMS 1
|
||||||
|
#define CONFIG_PANIC_HANG 1
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Env Settings
|
||||||
|
*/
|
||||||
|
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_UART)
|
||||||
|
# define CONFIG_BOOTDELAY -1
|
||||||
|
#else
|
||||||
|
# define CONFIG_BOOTDELAY 5
|
||||||
|
#endif
|
||||||
|
#define CONFIG_BOOTCOMMAND "run ramboot"
|
||||||
|
#ifdef CONFIG_VIDEO
|
||||||
|
# define CONFIG_BOOTARGS_VIDEO "console=tty0 "
|
||||||
|
#else
|
||||||
|
# define CONFIG_BOOTARGS_VIDEO ""
|
||||||
|
#endif
|
||||||
|
#define CONFIG_BOOTARGS \
|
||||||
|
"root=/dev/mtdblock0 rw " \
|
||||||
|
"earlyprintk=" \
|
||||||
|
"serial," \
|
||||||
|
"uart" MK_STR(CONFIG_UART_CONSOLE) "," \
|
||||||
|
MK_STR(CONFIG_BAUDRATE) " " \
|
||||||
|
CONFIG_BOOTARGS_VIDEO \
|
||||||
|
"console=ttyBF0," MK_STR(CONFIG_BAUDRATE)
|
||||||
|
|
||||||
|
#if defined(CONFIG_CMD_NET)
|
||||||
|
# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
|
||||||
|
# define UBOOT_ENV_FILE "u-boot.bin"
|
||||||
|
# else
|
||||||
|
# define UBOOT_ENV_FILE "u-boot.ldr"
|
||||||
|
# endif
|
||||||
|
# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
|
||||||
|
# ifdef CONFIG_SPI
|
||||||
|
# define UBOOT_ENV_UPDATE \
|
||||||
|
"eeprom write $(loadaddr) 0x0 $(filesize)"
|
||||||
|
# else
|
||||||
|
# define UBOOT_ENV_UPDATE \
|
||||||
|
"sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \
|
||||||
|
"sf erase 0 0x40000;" \
|
||||||
|
"sf write $(loadaddr) 0 $(filesize)"
|
||||||
|
# endif
|
||||||
|
# elif (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
|
||||||
|
# define UBOOT_ENV_UPDATE \
|
||||||
|
"nand unlock 0 0x40000;" \
|
||||||
|
"nand erase 0 0x40000;" \
|
||||||
|
"nand write $(loadaddr) 0 0x40000"
|
||||||
|
# else
|
||||||
|
# define UBOOT_ENV_UPDATE \
|
||||||
|
"protect off 0x20000000 0x2003FFFF;" \
|
||||||
|
"erase 0x20000000 0x2003FFFF;" \
|
||||||
|
"cp.b $(loadaddr) 0x20000000 $(filesize)"
|
||||||
|
# endif
|
||||||
|
# define NETWORK_ENV_SETTINGS \
|
||||||
|
"ubootfile=" UBOOT_ENV_FILE "\0" \
|
||||||
|
"update=" \
|
||||||
|
"tftp $(loadaddr) $(ubootfile);" \
|
||||||
|
UBOOT_ENV_UPDATE \
|
||||||
|
"\0" \
|
||||||
|
"addip=set bootargs $(bootargs) " \
|
||||||
|
"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
|
||||||
|
"$(hostname):eth0:off" \
|
||||||
|
"\0" \
|
||||||
|
"ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
|
||||||
|
"ramboot=" \
|
||||||
|
"tftp $(loadaddr) uImage;" \
|
||||||
|
"run ramargs;" \
|
||||||
|
"run addip;" \
|
||||||
|
"bootm" \
|
||||||
|
"\0" \
|
||||||
|
"nfsargs=set bootargs " \
|
||||||
|
"root=/dev/nfs rw " \
|
||||||
|
"nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
|
||||||
|
"\0" \
|
||||||
|
"nfsboot=" \
|
||||||
|
"tftp $(loadaddr) vmImage;" \
|
||||||
|
"run nfsargs;" \
|
||||||
|
"run addip;" \
|
||||||
|
"bootm" \
|
||||||
|
"\0"
|
||||||
|
#else
|
||||||
|
# define NETWORK_ENV_SETTINGS
|
||||||
|
#endif
|
||||||
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
||||||
|
NETWORK_ENV_SETTINGS \
|
||||||
|
"flashboot=bootm 0x20100000\0"
|
||||||
|
|
||||||
|
/*
|
||||||
|
* Network Settings
|
||||||
|
*/
|
||||||
|
#ifdef CONFIG_CMD_NET
|
||||||
|
# define CONFIG_IPADDR 192.168.0.15
|
||||||
|
# define CONFIG_NETMASK 255.255.255.0
|
||||||
|
# define CONFIG_GATEWAYIP 192.168.0.1
|
||||||
|
# define CONFIG_SERVERIP 192.168.0.2
|
||||||
|
# define CONFIG_ROOTPATH /romfs
|
||||||
|
# ifdef CONFIG_CMD_DHCP
|
||||||
|
# ifndef CONFIG_SYS_AUTOLOAD
|
||||||
|
# define CONFIG_SYS_AUTOLOAD "no"
|
||||||
|
# endif
|
||||||
|
# endif
|
||||||
|
# define CONFIG_NET_RETRY_COUNT 20
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#endif
|
||||||
Loading…
Reference in New Issue