powerpc/mpc85xx: Remove P1023 RDS support
Since P1023RDS is no longer supported/manufactured by Freescale, we clean up P1023RDS related code. Since P1023RDB is still supported by Freescale, we keep P1023RDB releated code. Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
This commit is contained in:
Lijun Pan
York Sun
parent
d43a386a91
commit
d0bc51407c
|
|
@ -1,9 +0,0 @@
|
||||||
#
|
|
||||||
# Copyright 2010-2011 Freescale Semiconductor, Inc.
|
|
||||||
#
|
|
||||||
# SPDX-License-Identifier: GPL-2.0+
|
|
||||||
#
|
|
||||||
|
|
||||||
obj-y += p1023rds.o
|
|
||||||
obj-y += law.o
|
|
||||||
obj-y += tlb.o
|
|
||||||
|
|
@ -1,101 +0,0 @@
|
||||||
Overview
|
|
||||||
--------
|
|
||||||
The P1023 process includes a performance optimized implementation of the
|
|
||||||
QorIQ data Path Acceleration Architecture (DPAA). This architecture
|
|
||||||
provides the infrastructure to support simplified sharing of networking
|
|
||||||
interfaces and accelerators by multiple CPU cores. P1023 is an e500 based
|
|
||||||
dual core SOC.
|
|
||||||
|
|
||||||
P1023RDS board is a Low End Dual core platform supporting the P1023
|
|
||||||
processor of QorIQ series.
|
|
||||||
|
|
||||||
Building U-boot
|
|
||||||
---------------
|
|
||||||
To build the u-boot for P1023RDS:
|
|
||||||
Configure to NOR boot:
|
|
||||||
make P1023RDS_config
|
|
||||||
Configure to NAND boot:
|
|
||||||
make P1023RDS_NAND_config
|
|
||||||
Build:
|
|
||||||
make
|
|
||||||
|
|
||||||
Board Switches
|
|
||||||
--------------
|
|
||||||
Most switches on the board should not be changed. The most frequent
|
|
||||||
user-settable switches on the board are used to configure
|
|
||||||
the flash banks.
|
|
||||||
|
|
||||||
J4: all open
|
|
||||||
|
|
||||||
Default NOR flash boot switch setting:
|
|
||||||
Sw3[1:8]: off on on off on on off off
|
|
||||||
Sw4[1:8]: off off off on off off off off
|
|
||||||
Sw6[1:8]: off on off on off on on off
|
|
||||||
Sw7[1:8]: off on off off on off off off
|
|
||||||
Sw8[1:8]: on off off off off off off off
|
|
||||||
|
|
||||||
For NAND flash boot,set
|
|
||||||
Sw4[1:4]: off on on on
|
|
||||||
|
|
||||||
The default native ethernet setting is for RGMII mode.
|
|
||||||
To use SGMII mode, set
|
|
||||||
SW8[1:2]: OFF OFF
|
|
||||||
SW7[6:7]: ON ON
|
|
||||||
|
|
||||||
Memory Map
|
|
||||||
----------
|
|
||||||
0x0000_0000 0x7fff_ffff DDR 2G Cacheable
|
|
||||||
0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
|
|
||||||
0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
|
|
||||||
0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
|
|
||||||
|
|
||||||
0xe000_0000 0xe003_ffff BCSR 256K BCSR
|
|
||||||
0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
|
|
||||||
0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
|
|
||||||
0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
|
|
||||||
0xffa0_0000 0xffaf_ffff NAND FLASH 1M non-cacheable
|
|
||||||
0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
|
|
||||||
|
|
||||||
Flashing u-boot Images
|
|
||||||
---------------
|
|
||||||
To program the image in the boot flash bank:
|
|
||||||
NOR flash boot:
|
|
||||||
=> tftp 1000000 u-boot.bin
|
|
||||||
=> protect off all
|
|
||||||
=> erase eff40000 efffffff
|
|
||||||
=> cp.b 1000000 eff40000 c0000
|
|
||||||
|
|
||||||
NAND flash boot:
|
|
||||||
=> tftp 1000000 u-boot-nand.bin
|
|
||||||
=> nand erase 0 80000
|
|
||||||
=> nand write 1000000 0 80000
|
|
||||||
|
|
||||||
Firmware ucode location
|
|
||||||
---------------------------------
|
|
||||||
Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work.
|
|
||||||
u-boot loads ucode FLASH. The location for ucode:
|
|
||||||
NOR Flash: 0xfe000000
|
|
||||||
NAND Flash: 0x1f00000
|
|
||||||
|
|
||||||
Using the Device Tree Source File
|
|
||||||
---------------------------------
|
|
||||||
To create the DTB (Device Tree Binary) image file,
|
|
||||||
use a command similar to this:
|
|
||||||
|
|
||||||
dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb
|
|
||||||
|
|
||||||
Likely, that .dts file will come from here;
|
|
||||||
|
|
||||||
linux-2.6/arch/powerpc/boot/dts/p1023rds.dts
|
|
||||||
or
|
|
||||||
make p1023rds.dtb ARCH=powerpc
|
|
||||||
in linux-2.6 directory.
|
|
||||||
|
|
||||||
Booting Linux
|
|
||||||
-------------
|
|
||||||
Place a linux uImage in the TFTP disk area.
|
|
||||||
|
|
||||||
tftp 1000000 uImage
|
|
||||||
tftp 2000000 rootfs.ext2.gz.uboot
|
|
||||||
tftp c00000 p1023rds.dtb
|
|
||||||
bootm 1000000 2000000 c00000
|
|
||||||
|
|
@ -1,49 +0,0 @@
|
||||||
/*
|
|
||||||
* Copyright (C) 2011 Freescale Semiconductor, Inc.
|
|
||||||
*
|
|
||||||
* Authors: Chunhe Lan <b25806@freescale.com>
|
|
||||||
*
|
|
||||||
* SPDX-License-Identifier: GPL-2.0+
|
|
||||||
*/
|
|
||||||
|
|
||||||
#ifndef __BCSR_H_
|
|
||||||
#define __BCSR_H_
|
|
||||||
|
|
||||||
#include <common.h>
|
|
||||||
|
|
||||||
/*
|
|
||||||
* BCSR Bit definitions
|
|
||||||
* BCSR 15 *
|
|
||||||
0 device insertion oriention
|
|
||||||
1 stack processor present
|
|
||||||
2 power supply shut down/normal operation
|
|
||||||
3 I2C bus0 drive enable
|
|
||||||
4 reserved
|
|
||||||
5:7 I2C bus0 select
|
|
||||||
5 - I2C_BUS_0_SS0
|
|
||||||
6 - I2C_BUS_0_SS1
|
|
||||||
7 - I2C_BUS_0_SS2
|
|
||||||
*/
|
|
||||||
|
|
||||||
/* BCSR register base address is 0xFX000020 */
|
|
||||||
#define BCSR_BASE_REG_OFFSET 0x20
|
|
||||||
#define BCSR_ACCESS_REG_ADDR (CONFIG_SYS_BCSR_BASE + BCSR_BASE_REG_OFFSET)
|
|
||||||
|
|
||||||
#define BCSR15_DEV_INS_ORI 0x80
|
|
||||||
#define BCSR15_STACK_PRO_PRE 0x40
|
|
||||||
#define BCSR15_POWER_SUPPLY 0x20
|
|
||||||
#define BCSR15_I2C_BUS0_EN 0x10
|
|
||||||
#define BCSR15_I2C_BUS0_SEG0 0x00
|
|
||||||
#define BCSR15_I2C_BUS0_SEG1 0x04
|
|
||||||
#define BCSR15_I2C_BUS0_SEG2 0x02
|
|
||||||
#define BCSR15_I2C_BUS0_SEG3 0x06
|
|
||||||
#define BCSR15_I2C_BUS0_SEG4 0x01
|
|
||||||
#define BCSR15_I2C_BUS0_SEG5 0x05
|
|
||||||
#define BCSR15_I2C_BUS0_SEG6 0x03
|
|
||||||
#define BCSR15_I2C_BUS0_SEG7 0x07
|
|
||||||
#define BCSR15_I2C_BUS0_SEG_CLR 0x07
|
|
||||||
#define BCSR19_SGMII_SEL_L 0x01
|
|
||||||
|
|
||||||
/*BCSR Utils functions*/
|
|
||||||
void fixup_i2c_bus0_sel_seg0(void);
|
|
||||||
#endif /* __BCSR_H_ */
|
|
||||||
|
|
@ -1,19 +0,0 @@
|
||||||
/*
|
|
||||||
* Copyright 2010-2011 Freescale Semiconductor, Inc.
|
|
||||||
*
|
|
||||||
* SPDX-License-Identifier: GPL-2.0+
|
|
||||||
*/
|
|
||||||
|
|
||||||
#include <common.h>
|
|
||||||
#include <asm/fsl_law.h>
|
|
||||||
#include <asm/mmu.h>
|
|
||||||
|
|
||||||
struct law_entry law_table[] = {
|
|
||||||
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
|
|
||||||
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_4M,
|
|
||||||
LAW_TRGT_IF_DPAA_SWP_SRAM),
|
|
||||||
/* The LAW 0xe0000000 ~ 0xefffffff for BCSR and NOR flash */
|
|
||||||
SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
|
|
||||||
};
|
|
||||||
|
|
||||||
int num_law_entries = ARRAY_SIZE(law_table);
|
|
||||||
|
|
@ -1,191 +0,0 @@
|
||||||
/*
|
|
||||||
* Copyright 2010-2012 Freescale Semiconductor, Inc.
|
|
||||||
*
|
|
||||||
* Authors: Roy Zang <tie-fei.zang@freescale.com>
|
|
||||||
* Chunhe Lan <b25806@freescale.com>
|
|
||||||
*
|
|
||||||
* SPDX-License-Identifier: GPL-2.0+
|
|
||||||
*/
|
|
||||||
|
|
||||||
#include <common.h>
|
|
||||||
#include <command.h>
|
|
||||||
#include <pci.h>
|
|
||||||
#include <asm/io.h>
|
|
||||||
#include <asm/cache.h>
|
|
||||||
#include <asm/processor.h>
|
|
||||||
#include <asm/mmu.h>
|
|
||||||
#include <asm/immap_85xx.h>
|
|
||||||
#include <asm/fsl_pci.h>
|
|
||||||
#include <fsl_ddr_sdram.h>
|
|
||||||
#include <asm/fsl_portals.h>
|
|
||||||
#include <libfdt.h>
|
|
||||||
#include <fdt_support.h>
|
|
||||||
#include <netdev.h>
|
|
||||||
#include <malloc.h>
|
|
||||||
#include <fm_eth.h>
|
|
||||||
#include <fsl_mdio.h>
|
|
||||||
#include <miiphy.h>
|
|
||||||
#include <phy.h>
|
|
||||||
#include <asm/fsl_dtsec.h>
|
|
||||||
|
|
||||||
#include "bcsr.h"
|
|
||||||
|
|
||||||
DECLARE_GLOBAL_DATA_PTR;
|
|
||||||
|
|
||||||
int board_early_init_f(void)
|
|
||||||
{
|
|
||||||
fsl_lbc_t *lbc = LBC_BASE_ADDR;
|
|
||||||
|
|
||||||
/* Set ABSWP to implement conversion of addresses in the LBC */
|
|
||||||
setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
|
|
||||||
|
|
||||||
return 0;
|
|
||||||
}
|
|
||||||
|
|
||||||
int checkboard(void)
|
|
||||||
{
|
|
||||||
u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
|
|
||||||
|
|
||||||
printf("Board: P1023 RDS\n");
|
|
||||||
|
|
||||||
clrbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG_CLR);
|
|
||||||
setbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG0);
|
|
||||||
|
|
||||||
return 0;
|
|
||||||
}
|
|
||||||
|
|
||||||
/* Fixed sdram init -- doesn't use serial presence detect. */
|
|
||||||
phys_size_t fixed_sdram(void)
|
|
||||||
{
|
|
||||||
#ifndef CONFIG_SYS_RAMBOOT
|
|
||||||
struct ccsr_ddr __iomem *ddr =
|
|
||||||
(struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
|
|
||||||
|
|
||||||
set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
|
|
||||||
|
|
||||||
out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
|
|
||||||
out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
|
|
||||||
out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
|
|
||||||
out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
|
|
||||||
out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
|
|
||||||
out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
|
|
||||||
out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
|
|
||||||
out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
|
|
||||||
out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
|
|
||||||
out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
|
|
||||||
out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
|
|
||||||
out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
|
|
||||||
out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
|
|
||||||
out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
|
|
||||||
out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
|
|
||||||
out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
|
|
||||||
out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
|
|
||||||
out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
|
|
||||||
out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
|
|
||||||
out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
|
|
||||||
out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
|
|
||||||
#endif
|
|
||||||
return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024ul;
|
|
||||||
}
|
|
||||||
|
|
||||||
#ifdef CONFIG_PCI
|
|
||||||
void pci_init_board(void)
|
|
||||||
{
|
|
||||||
fsl_pcie_init_board(0);
|
|
||||||
}
|
|
||||||
#endif
|
|
||||||
|
|
||||||
int board_early_init_r(void)
|
|
||||||
{
|
|
||||||
const unsigned int flashbase = CONFIG_SYS_BCSR_BASE;
|
|
||||||
const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Remap Boot flash + BCSR region to caching-inhibited
|
|
||||||
* so that flash can be erased properly.
|
|
||||||
*/
|
|
||||||
|
|
||||||
/* Flush d-cache and invalidate i-cache of any FLASH data */
|
|
||||||
flush_dcache();
|
|
||||||
invalidate_icache();
|
|
||||||
|
|
||||||
/* invalidate existing TLB entry for flash + bcsr */
|
|
||||||
disable_tlb(flash_esel);
|
|
||||||
|
|
||||||
set_tlb(1, flashbase, CONFIG_SYS_BCSR_BASE_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, flash_esel, BOOKE_PAGESZ_256M, 1);
|
|
||||||
|
|
||||||
setup_portals();
|
|
||||||
|
|
||||||
return 0;
|
|
||||||
}
|
|
||||||
|
|
||||||
unsigned long get_board_sys_clk(ulong dummy)
|
|
||||||
{
|
|
||||||
return gd->bus_clk;
|
|
||||||
}
|
|
||||||
|
|
||||||
unsigned long get_board_ddr_clk(ulong dummy)
|
|
||||||
{
|
|
||||||
return gd->mem_clk;
|
|
||||||
}
|
|
||||||
|
|
||||||
int board_eth_init(bd_t *bis)
|
|
||||||
{
|
|
||||||
u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
|
|
||||||
ccsr_gur_t *gur = (ccsr_gur_t *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
|
|
||||||
struct fsl_pq_mdio_info dtsec_mdio_info;
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Need to set dTSEC 1 pin multiplexing to TSEC. The default setting
|
|
||||||
* is not correct.
|
|
||||||
*/
|
|
||||||
setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_TSEC1_1);
|
|
||||||
|
|
||||||
dtsec_mdio_info.regs =
|
|
||||||
(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
|
|
||||||
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
|
|
||||||
|
|
||||||
/* Register the 1G MDIO bus */
|
|
||||||
fsl_pq_mdio_init(bis, &dtsec_mdio_info);
|
|
||||||
|
|
||||||
fm_info_set_phy_address(FM1_DTSEC1, CONFIG_SYS_FM1_DTSEC1_PHY_ADDR);
|
|
||||||
fm_info_set_phy_address(FM1_DTSEC2, CONFIG_SYS_FM1_DTSEC2_PHY_ADDR);
|
|
||||||
|
|
||||||
fm_info_set_mdio(FM1_DTSEC1,
|
|
||||||
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
|
|
||||||
fm_info_set_mdio(FM1_DTSEC2,
|
|
||||||
miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
|
|
||||||
|
|
||||||
/* Make SERDES connected to SGMII by cleaing bcsr19[7] */
|
|
||||||
if (fm_info_get_enet_if(FM1_DTSEC1) == PHY_INTERFACE_MODE_SGMII)
|
|
||||||
clrbits_8(&bcsr[19], BCSR19_SGMII_SEL_L);
|
|
||||||
|
|
||||||
#ifdef CONFIG_FMAN_ENET
|
|
||||||
cpu_eth_init(bis);
|
|
||||||
#endif
|
|
||||||
|
|
||||||
return pci_eth_init(bis);
|
|
||||||
}
|
|
||||||
|
|
||||||
#if defined(CONFIG_OF_BOARD_SETUP)
|
|
||||||
void ft_board_setup(void *blob, bd_t *bd)
|
|
||||||
{
|
|
||||||
phys_addr_t base;
|
|
||||||
phys_size_t size;
|
|
||||||
|
|
||||||
ft_cpu_setup(blob, bd);
|
|
||||||
|
|
||||||
base = getenv_bootm_low();
|
|
||||||
size = getenv_bootm_size();
|
|
||||||
|
|
||||||
fdt_fixup_memory(blob, (u64)base, (u64)size);
|
|
||||||
|
|
||||||
#ifdef CONFIG_HAS_FSL_DR_USB
|
|
||||||
fdt_fixup_dr_usb(blob, bd);
|
|
||||||
#endif
|
|
||||||
|
|
||||||
fdt_fixup_fman_ethernet(blob);
|
|
||||||
}
|
|
||||||
#endif
|
|
||||||
|
|
@ -1,100 +0,0 @@
|
||||||
/*
|
|
||||||
* Copyright 2010-2011 Freescale Semiconductor, Inc.
|
|
||||||
*
|
|
||||||
* SPDX-License-Identifier: GPL-2.0+
|
|
||||||
*/
|
|
||||||
|
|
||||||
#include <common.h>
|
|
||||||
#include <asm/mmu.h>
|
|
||||||
|
|
||||||
struct fsl_e_tlb_entry tlb_table[] = {
|
|
||||||
/* TLB 0 - for temp stack in cache */
|
|
||||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
||||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
|
|
||||||
CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
||||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
|
|
||||||
CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
||||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
|
|
||||||
CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
||||||
|
|
||||||
/* TLB 1 */
|
|
||||||
/* *I*** - Covers boot page */
|
|
||||||
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
|
|
||||||
0, 0, BOOKE_PAGESZ_4K, 1),
|
|
||||||
|
|
||||||
/* *I*G* - CCSRBAR */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 1, BOOKE_PAGESZ_4M, 1),
|
|
||||||
|
|
||||||
/* *W*G* - BCSR and NOR flash on local bus*/
|
|
||||||
/* This will be changed to *I*G* after relocation to RAM. */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
|
|
||||||
0, 2, BOOKE_PAGESZ_256M, 1),
|
|
||||||
|
|
||||||
/* *I*G* - PCI */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 3, BOOKE_PAGESZ_1G, 1),
|
|
||||||
|
|
||||||
/* *I*G* - PCI */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000,
|
|
||||||
CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 4, BOOKE_PAGESZ_256M, 1),
|
|
||||||
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000,
|
|
||||||
CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 5, BOOKE_PAGESZ_256M, 1),
|
|
||||||
|
|
||||||
/* *I*G* - PCI I/O */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 6, BOOKE_PAGESZ_256K, 1),
|
|
||||||
|
|
||||||
/* Bman/Qman */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 7, BOOKE_PAGESZ_1M, 1),
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
|
|
||||||
CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 8, BOOKE_PAGESZ_1M, 1),
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
|
|
||||||
0, 9, BOOKE_PAGESZ_1M, 1),
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
|
|
||||||
CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 10, BOOKE_PAGESZ_1M, 1),
|
|
||||||
|
|
||||||
/* *I*G - NAND */
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
||||||
0, 11, BOOKE_PAGESZ_1M, 1),
|
|
||||||
|
|
||||||
#ifdef CONFIG_SYS_RAMBOOT
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
|
|
||||||
CONFIG_SYS_DDR_SDRAM_BASE,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 12, BOOKE_PAGESZ_1G, 1),
|
|
||||||
|
|
||||||
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
|
|
||||||
CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
|
|
||||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
||||||
0, 13, BOOKE_PAGESZ_1G, 1),
|
|
||||||
#endif
|
|
||||||
};
|
|
||||||
|
|
||||||
int num_tlb_entries = ARRAY_SIZE(tlb_table);
|
|
||||||
|
|
@ -830,7 +830,6 @@ Active powerpc mpc85xx - freescale p1022ds
|
||||||
Active powerpc mpc85xx - freescale p1022ds P1022DS_SDCARD P1022DS:SDCARD Timur Tabi <timur@freescale.com>
|
Active powerpc mpc85xx - freescale p1022ds P1022DS_SDCARD P1022DS:SDCARD Timur Tabi <timur@freescale.com>
|
||||||
Active powerpc mpc85xx - freescale p1022ds P1022DS_SPIFLASH P1022DS:SPIFLASH Timur Tabi <timur@freescale.com>
|
Active powerpc mpc85xx - freescale p1022ds P1022DS_SPIFLASH P1022DS:SPIFLASH Timur Tabi <timur@freescale.com>
|
||||||
Active powerpc mpc85xx - freescale p1023rdb P1023RDB - -
|
Active powerpc mpc85xx - freescale p1023rdb P1023RDB - -
|
||||||
Active powerpc mpc85xx - freescale p1023rds P1023RDS - Roy Zang <tie-fei.zang@freescale.com>
|
|
||||||
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB P1_P2_RDB:P1011RDB -
|
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB P1_P2_RDB:P1011RDB -
|
||||||
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB_36BIT P1_P2_RDB:P1011RDB,36BIT -
|
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB_36BIT P1_P2_RDB:P1011RDB,36BIT -
|
||||||
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB_36BIT_SDCARD P1_P2_RDB:P1011RDB,36BIT,SDCARD -
|
Active powerpc mpc85xx - freescale p1_p2_rdb P1011RDB_36BIT_SDCARD P1_P2_RDB:P1011RDB,36BIT,SDCARD -
|
||||||
|
|
|
||||||
|
|
@ -1,479 +0,0 @@
|
||||||
/*
|
|
||||||
* Copyright 2010-2012 Freescale Semiconductor, Inc.
|
|
||||||
*
|
|
||||||
* Authors: Roy Zang <tie-fei.zang@freescale.com>
|
|
||||||
* Chunhe Lan <b25806@freescale.com>
|
|
||||||
*
|
|
||||||
* SPDX-License-Identifier: GPL-2.0+
|
|
||||||
*/
|
|
||||||
|
|
||||||
/*
|
|
||||||
* p1023rds board configuration file
|
|
||||||
*
|
|
||||||
*/
|
|
||||||
#ifndef __CONFIG_H
|
|
||||||
#define __CONFIG_H
|
|
||||||
|
|
||||||
#ifndef CONFIG_SYS_TEXT_BASE
|
|
||||||
#define CONFIG_SYS_TEXT_BASE 0xeff40000
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#ifndef CONFIG_SYS_MONITOR_BASE
|
|
||||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#ifndef CONFIG_RESET_VECTOR_ADDRESS
|
|
||||||
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/* High Level Configuration Options */
|
|
||||||
#define CONFIG_BOOKE /* BOOKE */
|
|
||||||
#define CONFIG_E500 /* BOOKE e500 family */
|
|
||||||
#define CONFIG_P1023
|
|
||||||
#define CONFIG_P1023RDS
|
|
||||||
#define CONFIG_MP /* support multiple processors */
|
|
||||||
|
|
||||||
#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
|
|
||||||
#define CONFIG_PCI /* Enable PCI/PCIE */
|
|
||||||
#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
|
|
||||||
#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */
|
|
||||||
#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */
|
|
||||||
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
|
|
||||||
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
||||||
#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
|
|
||||||
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
|
|
||||||
#define CONFIG_FSL_LAW /* Use common FSL init code */
|
|
||||||
|
|
||||||
#ifndef __ASSEMBLY__
|
|
||||||
extern unsigned long get_clock_freq(void);
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_SYS_CLK_FREQ 66666666
|
|
||||||
#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ
|
|
||||||
|
|
||||||
/*
|
|
||||||
* These can be toggled for performance analysis, otherwise use default.
|
|
||||||
*/
|
|
||||||
#define CONFIG_L2_CACHE /* toggle L2 cache */
|
|
||||||
#define CONFIG_BTB /* toggle branch predition */
|
|
||||||
#define CONFIG_HWCONFIG
|
|
||||||
|
|
||||||
#define CONFIG_ENABLE_36BIT_PHYS
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
|
|
||||||
#define CONFIG_SYS_MEMTEST_END 0x1fffffff /* fix me, only 1G */
|
|
||||||
#define CONFIG_PANIC_HANG /* do not reset board on panic */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_LBC_LBCR 0x00000000 /* Implement conversion of
|
|
||||||
addresses in the LBC */
|
|
||||||
|
|
||||||
/* DDR Setup */
|
|
||||||
#define CONFIG_VERY_BIG_RAM
|
|
||||||
|
|
||||||
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
|
||||||
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
|
|
||||||
|
|
||||||
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
|
||||||
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
|
||||||
|
|
||||||
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
|
||||||
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
|
|
||||||
|
|
||||||
/* These are used when DDR doesn't use SPD. */
|
|
||||||
#define CONFIG_SYS_SDRAM_SIZE 2048u /* DDR is 2GB */
|
|
||||||
|
|
||||||
/* Default settings for "stable" mode */
|
|
||||||
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
|
|
||||||
#define CONFIG_SYS_DDR_CS1_BNDS 0x0040007F
|
|
||||||
#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302
|
|
||||||
#define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_3 0x00020000
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_0 0x40110104
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_1 0x5C59E544
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_2 0x0fA888CA
|
|
||||||
#define CONFIG_SYS_DDR_MODE_1 0x00441210
|
|
||||||
#define CONFIG_SYS_DDR_MODE_2 0x00000000
|
|
||||||
#define CONFIG_SYS_DDR_MODE_CTRL 0x00000000
|
|
||||||
#define CONFIG_SYS_DDR_INTERVAL 0x0A280100
|
|
||||||
#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
|
|
||||||
#define CONFIG_SYS_DDR_CLK_CTRL 0x01800000
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_4 0x00000001
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_5 0x01401400
|
|
||||||
#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600
|
|
||||||
#define CONFIG_SYS_DDR_WRLVL_CNTL 0x8675F605
|
|
||||||
#define CONFIG_SYS_DDR_CONTROL 0xC70C0008 /* Type = DDR3: No Interleaving */
|
|
||||||
#define CONFIG_SYS_DDR_CONTROL2 0x24401010
|
|
||||||
#define CONFIG_SYS_DDR_CDR1 0x00000000
|
|
||||||
#define CONFIG_SYS_DDR_CDR2 0x00000000
|
|
||||||
|
|
||||||
#define CONFIG_SYS_DDR_ERR_INT_EN 0x00000000
|
|
||||||
#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
|
|
||||||
#define CONFIG_SYS_DDR_SBE 0x00000000
|
|
||||||
|
|
||||||
/* Settings that differ for "performance" mode */
|
|
||||||
#define CONFIG_SYS_DDR_CS0_BNDS_PERF 0x0000007F /* Interleaving Enabled */
|
|
||||||
#define CONFIG_SYS_DDR_CS1_BNDS_PERF 0x00000000 /* Interleaving Enabled */
|
|
||||||
#define CONFIG_SYS_DDR_CS1_CONFIG_PERF 0x80014302
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_1_PERF 0x5C58E544
|
|
||||||
#define CONFIG_SYS_DDR_TIMING_2_PERF 0x0FA888CA
|
|
||||||
/* Type = DDR3: cs0-cs1 interleaving */
|
|
||||||
#define CONFIG_SYS_DDR_CONTROL_PERF 0xC70C4008
|
|
||||||
#define CONFIG_SYS_DDR_CDR_1 0x00000000
|
|
||||||
#define CONFIG_SYS_DDR_CDR_2 0x00000000
|
|
||||||
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Memory map
|
|
||||||
*
|
|
||||||
* 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
|
|
||||||
* 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
|
|
||||||
* 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
|
|
||||||
* 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
|
|
||||||
*
|
|
||||||
* Localbus non-cacheable
|
|
||||||
* 0xe000_0000 0xe003_ffff BCSR 256K BCSR
|
|
||||||
* 0xee00_0000 0xefff_ffff NOR flash 32M NOR flash
|
|
||||||
* 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M
|
|
||||||
* 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
|
|
||||||
* 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
|
|
||||||
* 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0
|
|
||||||
*/
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Local Bus Definitions
|
|
||||||
*/
|
|
||||||
#define CONFIG_SYS_BCSR_BASE 0xe0000000 /* start of on board FPGA */
|
|
||||||
#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_BASE 0xee000000 /* start of FLASH 32M */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
|
|
||||||
|
|
||||||
#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
|
|
||||||
| BR_PS_16 | BR_V)
|
|
||||||
#define CONFIG_FLASH_OR_PRELIM 0xfe000ff7
|
|
||||||
|
|
||||||
#define CONFIG_FLASH_CFI_DRIVER
|
|
||||||
#define CONFIG_SYS_FLASH_CFI
|
|
||||||
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
|
||||||
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
|
|
||||||
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
|
||||||
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
|
||||||
|
|
||||||
#if defined(CONFIG_SYS_SPL)
|
|
||||||
#define CONFIG_SYS_RAMBOOT
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
|
|
||||||
#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_INIT_RAM_LOCK
|
|
||||||
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
|
|
||||||
#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End of used area in RAM */
|
|
||||||
|
|
||||||
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
|
||||||
(CONFIG_SYS_INIT_RAM_END - GENERATED_GBL_DATA_SIZE)
|
|
||||||
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
||||||
|
|
||||||
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
|
|
||||||
#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
|
|
||||||
|
|
||||||
#ifndef CONFIG_NAND_SPL
|
|
||||||
#define CONFIG_SYS_NAND_BASE 0xffa00000
|
|
||||||
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
|
|
||||||
#else
|
|
||||||
#define CONFIG_SYS_NAND_BASE 0xfff00000
|
|
||||||
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
|
|
||||||
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
||||||
#define CONFIG_MTD_NAND_VERIFY_WRITE
|
|
||||||
#define CONFIG_CMD_NAND
|
|
||||||
#define CONFIG_NAND_FSL_ELBC
|
|
||||||
#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
|
|
||||||
|
|
||||||
/* NAND boot: 4K NAND loader config */
|
|
||||||
#define CONFIG_SYS_NAND_SPL_SIZE 0x1000
|
|
||||||
#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
|
|
||||||
#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
|
|
||||||
#define CONFIG_SYS_NAND_U_BOOT_START 0x11000000
|
|
||||||
#define CONFIG_SYS_NAND_U_BOOT_OFFS (0)
|
|
||||||
#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
|
|
||||||
#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
|
|
||||||
|
|
||||||
/* NAND flash config */
|
|
||||||
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
|
||||||
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
|
|
||||||
| BR_PS_8 /* Port Size = 8bit */ \
|
|
||||||
| BR_MS_FCM /* MSEL = FCM */ \
|
|
||||||
| BR_V) /* valid */
|
|
||||||
#define CONFIG_SYS_NAND_OR_PRELIM (0xFFF80000 /* length 32K */ \
|
|
||||||
| OR_FCM_CSCT \
|
|
||||||
| OR_FCM_CST \
|
|
||||||
| OR_FCM_CHT \
|
|
||||||
| OR_FCM_SCY_1 \
|
|
||||||
| OR_FCM_TRLX \
|
|
||||||
| OR_FCM_EHTR)
|
|
||||||
|
|
||||||
#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
|
|
||||||
#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
|
|
||||||
/* chip select 1 - BCSR */
|
|
||||||
#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
|
|
||||||
| BR_MS_GPCM | BR_PS_8 | BR_V)
|
|
||||||
#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
|
|
||||||
| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
|
|
||||||
| OR_GPCM_EAD)
|
|
||||||
|
|
||||||
/* Serial Port
|
|
||||||
* open - index 2
|
|
||||||
* shorted - index 1
|
|
||||||
*/
|
|
||||||
#define CONFIG_CONS_INDEX 1
|
|
||||||
#undef CONFIG_SERIAL_SOFTWARE_FIFO
|
|
||||||
#define CONFIG_SYS_NS16550
|
|
||||||
#define CONFIG_SYS_NS16550_SERIAL
|
|
||||||
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
|
||||||
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
|
||||||
#ifdef CONFIG_NAND_SPL
|
|
||||||
#define CONFIG_NS16550_MIN_FUNCTIONS
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_SYS_BAUDRATE_TABLE \
|
|
||||||
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
|
|
||||||
|
|
||||||
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
|
|
||||||
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)
|
|
||||||
|
|
||||||
/* Use the HUSH parser */
|
|
||||||
#define CONFIG_SYS_HUSH_PARSER
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Pass open firmware flat tree
|
|
||||||
*/
|
|
||||||
#define CONFIG_OF_LIBFDT
|
|
||||||
#define CONFIG_OF_BOARD_SETUP
|
|
||||||
#define CONFIG_OF_STDOUT_VIA_ALIAS
|
|
||||||
|
|
||||||
/* new uImage format support */
|
|
||||||
#define CONFIG_FIT
|
|
||||||
#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
|
|
||||||
|
|
||||||
/* I2C */
|
|
||||||
#define CONFIG_SYS_I2C
|
|
||||||
#define CONFIG_SYS_I2C_FSL
|
|
||||||
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
|
||||||
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
|
||||||
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
|
||||||
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
|
|
||||||
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
|
||||||
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
|
|
||||||
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
|
|
||||||
|
|
||||||
/*
|
|
||||||
* I2C2 EEPROM
|
|
||||||
*/
|
|
||||||
#define CONFIG_ID_EEPROM
|
|
||||||
#ifdef CONFIG_ID_EEPROM
|
|
||||||
#define CONFIG_SYS_I2C_EEPROM_NXID
|
|
||||||
#endif
|
|
||||||
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x51
|
|
||||||
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
||||||
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
|
||||||
|
|
||||||
#define CONFIG_CMD_I2C
|
|
||||||
|
|
||||||
/*
|
|
||||||
* eSPI - Enhanced SPI
|
|
||||||
*/
|
|
||||||
#define CONFIG_SPI_FLASH
|
|
||||||
#define CONFIG_SPI_FLASH_ATMEL
|
|
||||||
|
|
||||||
#define CONFIG_HARD_SPI
|
|
||||||
#define CONFIG_FSL_ESPI
|
|
||||||
|
|
||||||
#define CONFIG_CMD_SF
|
|
||||||
#define CONFIG_SF_DEFAULT_SPEED 10000000
|
|
||||||
#define CONFIG_SF_DEFAULT_MODE 0
|
|
||||||
|
|
||||||
/*
|
|
||||||
* General PCI
|
|
||||||
* Memory space is mapped 1-1, but I/O space must start from 0.
|
|
||||||
*/
|
|
||||||
|
|
||||||
/* controller 3, Slot 1, tgtid 3, Base address b000 */
|
|
||||||
#define CONFIG_SYS_PCIE3_NAME "Slot 3"
|
|
||||||
#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
|
|
||||||
#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
|
|
||||||
#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
|
|
||||||
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
|
|
||||||
#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
|
|
||||||
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
|
||||||
#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
|
|
||||||
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
|
||||||
|
|
||||||
/* controller 2, direct to uli, tgtid 2, Base address 9000 */
|
|
||||||
#define CONFIG_SYS_PCIE2_NAME "Slot 2"
|
|
||||||
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
|
|
||||||
#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
|
|
||||||
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
|
|
||||||
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
|
|
||||||
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
|
|
||||||
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
|
||||||
#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
|
|
||||||
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
|
|
||||||
|
|
||||||
/* controller 1, Slot 2, tgtid 1, Base address a000 */
|
|
||||||
#define CONFIG_SYS_PCIE1_NAME "Slot 1"
|
|
||||||
#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
|
|
||||||
#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
|
|
||||||
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
|
|
||||||
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
|
|
||||||
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
|
|
||||||
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
|
||||||
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
|
|
||||||
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
|
||||||
|
|
||||||
#if defined(CONFIG_PCI)
|
|
||||||
#define CONFIG_E1000 /* Defind e1000 pci Ethernet card */
|
|
||||||
#define CONFIG_PCI_PNP /* do pci plug-and-play */
|
|
||||||
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
||||||
#endif /* CONFIG_PCI */
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Environment
|
|
||||||
*/
|
|
||||||
#define CONFIG_ENV_OVERWRITE
|
|
||||||
|
|
||||||
#if defined(CONFIG_SYS_RAMBOOT)
|
|
||||||
#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
|
|
||||||
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x4000)
|
|
||||||
#define CONFIG_ENV_SIZE 0x2000
|
|
||||||
#else
|
|
||||||
#define CONFIG_ENV_IS_IN_FLASH
|
|
||||||
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
|
|
||||||
#define CONFIG_ENV_SIZE 0x2000
|
|
||||||
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
|
||||||
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Command line configuration.
|
|
||||||
*/
|
|
||||||
#include <config_cmd_default.h>
|
|
||||||
|
|
||||||
#define CONFIG_CMD_IRQ
|
|
||||||
#define CONFIG_CMD_PING
|
|
||||||
#define CONFIG_CMD_MII
|
|
||||||
#define CONFIG_CMD_ELF
|
|
||||||
#define CONFIG_CMD_SETEXPR
|
|
||||||
#define CONFIG_CMD_REGINFO
|
|
||||||
|
|
||||||
#if defined(CONFIG_PCI)
|
|
||||||
#define CONFIG_CMD_PCI
|
|
||||||
#define CONFIG_CMD_NET
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
|
||||||
* USB
|
|
||||||
*/
|
|
||||||
#define CONFIG_HAS_FSL_DR_USB
|
|
||||||
#ifdef CONFIG_HAS_FSL_DR_USB
|
|
||||||
#define CONFIG_USB_EHCI
|
|
||||||
|
|
||||||
#ifdef CONFIG_USB_EHCI
|
|
||||||
#define CONFIG_CMD_USB
|
|
||||||
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
|
||||||
#define CONFIG_USB_EHCI_FSL
|
|
||||||
#define CONFIG_USB_STORAGE
|
|
||||||
#define CONFIG_CMD_FAT
|
|
||||||
#define CONFIG_CMD_EXT2
|
|
||||||
#define CONFIG_CMD_FAT
|
|
||||||
#define CONFIG_DOS_PARTITION
|
|
||||||
#endif
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Miscellaneous configurable options
|
|
||||||
*/
|
|
||||||
#define CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
||||||
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
|
|
||||||
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
|
||||||
#if defined(CONFIG_CMD_KGDB)
|
|
||||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
||||||
#else
|
|
||||||
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
||||||
#endif
|
|
||||||
/* Print Buffer Size */
|
|
||||||
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
|
|
||||||
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
||||||
/* Boot Argument Buffer Size */
|
|
||||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
|
||||||
|
|
||||||
/*
|
|
||||||
* For booting Linux, the board info and command line data
|
|
||||||
* have to be in the first 16 MB of memory, since this is
|
|
||||||
* the maximum mapped by the Linux kernel during initialization.
|
|
||||||
*/
|
|
||||||
#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
|
|
||||||
#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
|
|
||||||
|
|
||||||
#if defined(CONFIG_CMD_KGDB)
|
|
||||||
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/*
|
|
||||||
* Environment Configuration
|
|
||||||
*/
|
|
||||||
#define CONFIG_BOOTFILE "uImage"
|
|
||||||
#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */
|
|
||||||
|
|
||||||
/* default location for tftp and bootm */
|
|
||||||
#define CONFIG_LOADADDR 1000000
|
|
||||||
|
|
||||||
#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
|
|
||||||
|
|
||||||
#define CONFIG_BAUDRATE 115200
|
|
||||||
|
|
||||||
/* Qman/Bman */
|
|
||||||
#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
|
|
||||||
#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
|
|
||||||
#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
|
|
||||||
#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
|
|
||||||
#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
|
|
||||||
#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
|
|
||||||
#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
|
|
||||||
|
|
||||||
/* For FM */
|
|
||||||
#define CONFIG_SYS_DPAA_FMAN
|
|
||||||
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
|
|
||||||
|
|
||||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
|
||||||
#define CONFIG_FMAN_ENET
|
|
||||||
#define CONFIG_PHY_MARVELL
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/* Default address of microcode for the Linux Fman driver */
|
|
||||||
/* QE microcode/firmware address */
|
|
||||||
#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
|
|
||||||
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
|
|
||||||
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
|
||||||
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
|
||||||
|
|
||||||
#ifdef CONFIG_FMAN_ENET
|
|
||||||
#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2
|
|
||||||
#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x7
|
|
||||||
|
|
||||||
#define CONFIG_SYS_TBIPA_VALUE 8
|
|
||||||
#define CONFIG_MII /* MII PHY management */
|
|
||||||
#define CONFIG_ETHPRIME "FM1@DTSEC1"
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
||||||
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
|
|
||||||
|
|
||||||
#endif /* __CONFIG_H */
|
|
||||||
Loading…
Reference in New Issue