Merge git://www.denx.de/git/u-boot-i2c

arch/arm/Kconfig

@@ -406,6 +406,7 @@ config TARGET_BCMNSP
 config ARCH_EXYNOS
 	bool "Samsung EXYNOS"
 	select DM
+	select DM_I2C
 	select DM_SPI_FLASH
 	select DM_SERIAL
 	select DM_SPI
@@ -418,6 +419,7 @@ config ARCH_S5PC1XX
 	select DM
 	select DM_SERIAL
 	select DM_GPIO
+	select DM_I2C
 
 config ARCH_HIGHBANK
 	bool "Calxeda Highbank"

board/samsung/common/misc.c

@@ -101,6 +101,7 @@ void set_board_info(void)
 #ifdef CONFIG_LCD_MENU
 static int power_key_pressed(u32 reg)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	struct pmic *pmic;
 	u32 status;
 	u32 mask;
@@ -123,6 +124,9 @@ static int power_key_pressed(u32 reg)
 		return 0;
 
 	return !!(status & mask);
+#else
+	return 0;
+#endif
 }
 
 static int key_pressed(int key)

board/samsung/goni/goni.c

@@ -45,11 +45,15 @@ void i2c_init_board(void)
 
 int power_init_board(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	/*
 	 * For PMIC the I2C bus is named as I2C5, but it is connected
 	 * to logical I2C adapter 0
 	 */
 	return pmic_init(I2C_0);
+#else
+	return 0;
+#endif
 }
 
 int dram_init(void)
@@ -142,6 +146,7 @@ int board_mmc_init(bd_t *bis)
 #ifdef CONFIG_USB_GADGET
 static int s5pc1xx_phy_control(int on)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret;
 	static int status;
 	struct pmic *p = pmic_get("MAX8998_PMIC");
@@ -173,7 +178,7 @@ static int s5pc1xx_phy_control(int on)
 		status = 0;
 	}
 	udelay(10000);
-
+#endif
 	return 0;
 }
 

board/samsung/trats/trats.c

@@ -53,6 +53,7 @@ int exynos_init(void)
 
 void i2c_init_board(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int err;
 
 	/* I2C_5 -> PMIC */
@@ -67,8 +68,10 @@ void i2c_init_board(void)
 	gpio_request(EXYNOS4_GPIO_Y41, "i2c_data");
 	gpio_direction_output(EXYNOS4_GPIO_Y40, 1);
 	gpio_direction_output(EXYNOS4_GPIO_Y41, 1);
+#endif
 }
 
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 static void trats_low_power_mode(void)
 {
 	struct exynos4_clock *clk =
@@ -273,11 +276,14 @@ static int pmic_init_max8997(void)
 		puts("MAX8997 PMIC setting error!\n");
 		return -1;
 	}
+
 	return 0;
 }
+#endif
 
 int exynos_power_init(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int chrg, ret;
 	struct power_battery *pb;
 	struct pmic *p_fg, *p_chrg, *p_muic, *p_bat;
@@ -341,6 +347,7 @@ int exynos_power_init(void)
 
 	if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
 		puts("CHARGE Battery !\n");
+#endif
 
 	return 0;
 }
@@ -384,6 +391,7 @@ static void check_hw_revision(void)
 #ifdef CONFIG_USB_GADGET
 static int s5pc210_phy_control(int on)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret = 0;
 	u32 val = 0;
 	struct pmic *p = pmic_get("MAX8997_PMIC");
@@ -415,6 +423,7 @@ static int s5pc210_phy_control(int on)
 		puts("MAX8997 LDO setting error!\n");
 		return -1;
 	}
+#endif
 
 	return 0;
 }
@@ -435,11 +444,16 @@ int board_usb_init(int index, enum usb_init_type init)
 
 int g_dnl_board_usb_cable_connected(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	struct pmic *muic = pmic_get("MAX8997_MUIC");
 	if (!muic)
 		return 0;
 
 	return !!muic->chrg->chrg_type(muic);
+#else
+	return false;
+#endif
+
 }
 #endif
 
@@ -552,6 +566,7 @@ void exynos_reset_lcd(void)
 
 int lcd_power(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret = 0;
 	struct pmic *p = pmic_get("MAX8997_PMIC");
 	if (!p)
@@ -569,12 +584,13 @@ int lcd_power(void)
 		puts("MAX8997 LDO setting error!\n");
 		return -1;
 	}
-
+#endif
 	return 0;
 }
 
 int mipi_power(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret = 0;
 	struct pmic *p = pmic_get("MAX8997_PMIC");
 	if (!p)
@@ -592,7 +608,7 @@ int mipi_power(void)
 		puts("MAX8997 LDO setting error!\n");
 		return -1;
 	}
-
+#endif
 	return 0;
 }
 

board/samsung/trats2/trats2.c

@@ -151,8 +151,6 @@ int exynos_early_init_f(void)
 	return 0;
 }
 
-static int pmic_init_max77686(void);
-
 int exynos_init(void)
 {
 	struct exynos4_power *pwr =
@@ -176,6 +174,7 @@ int exynos_init(void)
 
 int exynos_power_init(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int chrg;
 	struct power_battery *pb;
 	struct pmic *p_chrg, *p_muic, *p_fg, *p_bat;
@@ -236,13 +235,14 @@ int exynos_power_init(void)
 
 	if (pb->bat->state == CHARGE && chrg == CHARGER_USB)
 		puts("CHARGE Battery !\n");
-
+#endif
 	return 0;
 }
 
 #ifdef CONFIG_USB_GADGET
 static int s5pc210_phy_control(int on)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret = 0;
 	unsigned int val;
 	struct pmic *p, *p_pmic, *p_muic;
@@ -299,7 +299,7 @@ static int s5pc210_phy_control(int on)
 
 	if (ret)
 		return -1;
-
+#endif
 	return 0;
 }
 
@@ -319,14 +319,19 @@ int board_usb_init(int index, enum usb_init_type init)
 
 int g_dnl_board_usb_cable_connected(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	struct pmic *muic = pmic_get("MAX77693_MUIC");
 	if (!muic)
 		return 0;
 
 	return !!muic->chrg->chrg_type(muic);
+#else
+	return false;
+#endif
 }
 #endif
 
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 static int pmic_init_max77686(void)
 {
 	struct pmic *p = pmic_get("MAX77686_PMIC");
@@ -379,6 +384,7 @@ static int pmic_init_max77686(void)
 
 	return 0;
 }
+#endif
 
 /*
  * LCD
@@ -387,18 +393,21 @@ static int pmic_init_max77686(void)
 #ifdef CONFIG_LCD
 int mipi_power(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	struct pmic *p = pmic_get("MAX77686_PMIC");
 
 	/* LDO8 VMIPI_1.0V_AP */
 	max77686_set_ldo_mode(p, 8, OPMODE_ON);
 	/* LDO10 VMIPI_1.8V_AP */
 	max77686_set_ldo_mode(p, 10, OPMODE_ON);
+#endif
 
 	return 0;
 }
 
 void exynos_lcd_power_on(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	struct pmic *p = pmic_get("MAX77686_PMIC");
 
 	/* LCD_2.2V_EN: GPC0[1] */
@@ -410,6 +419,7 @@ void exynos_lcd_power_on(void)
 	pmic_probe(p);
 	max77686_set_ldo_voltage(p, 25, 3100000);
 	max77686_set_ldo_mode(p, 25, OPMODE_LPM);
+#endif
 }
 
 void exynos_reset_lcd(void)

board/samsung/universal_c210/universal.c

@@ -38,10 +38,9 @@ static int get_hwrev(void)
 	return board_rev & 0xFF;
 }
 
-static void init_pmic_lcd(void);
-
 int exynos_power_init(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret;
 
 	/*
@@ -53,7 +52,7 @@ int exynos_power_init(void)
 		return ret;
 
 	init_pmic_lcd();
-
+#endif
 	return 0;
 }
 
@@ -84,6 +83,7 @@ static unsigned short get_adc_value(int channel)
 
 static int adc_power_control(int on)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret;
 	struct pmic *p = pmic_get("MAX8998_PMIC");
 	if (!p)
@@ -97,6 +97,9 @@ static int adc_power_control(int on)
 			      MAX8998_LDO4, !!on);
 
 	return ret;
+#else
+	return 0;
+#endif
 }
 
 static unsigned int get_hw_revision(void)
@@ -144,6 +147,7 @@ static void check_hw_revision(void)
 #ifdef CONFIG_USB_GADGET
 static int s5pc210_phy_control(int on)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	int ret = 0;
 	struct pmic *p = pmic_get("MAX8998_PMIC");
 	if (!p)
@@ -175,7 +179,7 @@ static int s5pc210_phy_control(int on)
 		puts("MAX8998 LDO setting error!\n");
 		return -1;
 	}
-
+#endif
 	return 0;
 }
 
@@ -201,6 +205,7 @@ int exynos_early_init_f(void)
 	return 0;
 }
 
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 static void init_pmic_lcd(void)
 {
 	unsigned char val;
@@ -248,6 +253,7 @@ static void init_pmic_lcd(void)
 	if (ret)
 		puts("LCD pmic initialisation error!\n");
 }
+#endif
 
 void exynos_cfg_lcd_gpio(void)
 {
@@ -304,6 +310,7 @@ void exynos_reset_lcd(void)
 
 void exynos_lcd_power_on(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	struct pmic *p = pmic_get("MAX8998_PMIC");
 
 	if (!p)
@@ -314,6 +321,7 @@ void exynos_lcd_power_on(void)
 
 	pmic_set_output(p, MAX8998_REG_ONOFF3, MAX8998_LDO17, LDO_ON);
 	pmic_set_output(p, MAX8998_REG_ONOFF2, MAX8998_LDO7, LDO_ON);
+#endif
 }
 
 void exynos_cfg_ldo(void)
@@ -328,8 +336,9 @@ void exynos_enable_ldo(unsigned int onoff)
 
 int exynos_init(void)
 {
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	char buf[16];
-
+#endif
 	gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210;
 
 	switch (get_hwrev()) {
@@ -354,13 +363,14 @@ int exynos_init(void)
 		break;
 	}
 
+#ifndef CONFIG_DM_I2C /* TODO(maintainer): Convert to driver model */
 	/* Request soft I2C gpios */
 	strcpy(buf, "soft_i2c_scl");
 	gpio_request(CONFIG_SOFT_I2C_GPIO_SCL, buf);
 
 	strcpy(buf, "soft_i2c_sda");
 	gpio_request(CONFIG_SOFT_I2C_GPIO_SDA, buf);
-
+#endif
 	check_hw_revision();
 	printf("HW Revision:\t0x%x\n", board_rev);
 

configs/origen_defconfig

@@ -37,3 +37,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_G_DNL_MANUFACTURER="Samsung"
 CONFIG_G_DNL_VENDOR_NUM=0x04e8
 CONFIG_G_DNL_PRODUCT_NUM=0x6601
+CONFIG_DM_I2C=y

doc/driver-model/i2c-howto.txt

@@ -0,0 +1,56 @@
+How to port a serial driver to driver model
+===========================================
+
+Over half of the I2C drivers have been converted as at November 2016. These
+ones remain:
+
+   adi_i2c
+   davinci_i2c
+   fti2c010
+   ihs_i2c
+   kona_i2c
+   lpc32xx_i2c
+   pca9564_i2c
+   ppc4xx_i2c
+   rcar_i2c
+   sh_i2c
+   sh_sh7734_i2c
+   soft_i2c
+   tsi108_i2c
+   zynq_i2c
+
+The deadline for this work is the end of June 2017. If no one steps
+forward to convert these, at some point there may come a patch to remove them!
+
+Here is a suggested approach for converting your I2C driver over to driver
+model. Please feel free to update this file with your ideas and suggestions.
+
+- #ifdef out all your own I2C driver code (#ifndef CONFIG_DM_I2C)
+- Define CONFIG_DM_I2C for your board, vendor or architecture
+- If the board does not already use driver model, you need CONFIG_DM also
+- Your board should then build, but will not work fully since there will be
+    no I2C driver
+- Add the U_BOOT_DRIVER piece at the end (e.g. copy tegra_i2c.c for example)
+- Add a private struct for the driver data - avoid using static variables
+- Implement each of the driver methods, perhaps by calling your old methods
+- You may need to adjust the function parameters so that the old and new
+    implementations can share most of the existing code
+- If you convert all existing users of the driver, remove the pre-driver-model
+    code
+
+In terms of patches a conversion series typically has these patches:
+- clean up / prepare the driver for conversion
+- add driver model code
+- convert at least one existing board to use driver model serial
+- (if no boards remain that don't use driver model) remove the old code
+
+This may be a good time to move your board to use device tree also. Mostly
+this involves these steps:
+
+- define CONFIG_OF_CONTROL and CONFIG_OF_SEPARATE
+- add your device tree files to arch/<arch>/dts
+- update the Makefile there
+- Add stdout-path to your /chosen device tree node if it is not already there
+- build and get u-boot-dtb.bin so you can test it
+- Your drivers can now use device tree
+- For device tree in SPL, define CONFIG_SPL_OF_CONTROL

drivers/i2c/Makefile

@@ -34,7 +34,7 @@ obj-$(CONFIG_SYS_I2C_OMAP34XX) += omap24xx_i2c.o
 obj-$(CONFIG_SYS_I2C_PPC4XX) += ppc4xx_i2c.o
 obj-$(CONFIG_SYS_I2C_RCAR) += rcar_i2c.o
 obj-$(CONFIG_SYS_I2C_ROCKCHIP) += rk_i2c.o
-obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o
+obj-$(CONFIG_SYS_I2C_S3C24X0) += s3c24x0_i2c.o exynos_hs_i2c.o
 obj-$(CONFIG_SYS_I2C_SANDBOX) += sandbox_i2c.o i2c-emul-uclass.o
 obj-$(CONFIG_SYS_I2C_SH) += sh_i2c.o
 obj-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o

drivers/i2c/adi_i2c.c

@@ -4,6 +4,9 @@
  * Copyright (c) 2006-2014 Analog Devices Inc.
  *
  * Licensed under the GPL-2 or later.
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/davinci_i2c.c

@@ -7,6 +7,9 @@
  * --------------------------------------------------------
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/exynos_hs_i2c.c

@@ -0,0 +1,561 @@
+/*
+ * Copyright (c) 2016, Google Inc
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, d.mueller@elsoft.ch
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <i2c.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/pinmux.h>
+#include "s3c24x0_i2c.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* HSI2C-specific register description */
+
+/* I2C_CTL Register bits */
+#define HSI2C_FUNC_MODE_I2C		(1u << 0)
+#define HSI2C_MASTER			(1u << 3)
+#define HSI2C_RXCHON			(1u << 6)	/* Write/Send */
+#define HSI2C_TXCHON			(1u << 7)	/* Read/Receive */
+#define HSI2C_SW_RST			(1u << 31)
+
+/* I2C_FIFO_CTL Register bits */
+#define HSI2C_RXFIFO_EN			(1u << 0)
+#define HSI2C_TXFIFO_EN			(1u << 1)
+#define HSI2C_TXFIFO_TRIGGER_LEVEL	(0x20 << 16)
+#define HSI2C_RXFIFO_TRIGGER_LEVEL	(0x20 << 4)
+
+/* I2C_TRAILING_CTL Register bits */
+#define HSI2C_TRAILING_COUNT		(0xff)
+
+/* I2C_INT_EN Register bits */
+#define HSI2C_TX_UNDERRUN_EN		(1u << 2)
+#define HSI2C_TX_OVERRUN_EN		(1u << 3)
+#define HSI2C_RX_UNDERRUN_EN		(1u << 4)
+#define HSI2C_RX_OVERRUN_EN		(1u << 5)
+#define HSI2C_INT_TRAILING_EN		(1u << 6)
+#define HSI2C_INT_I2C_EN		(1u << 9)
+
+#define HSI2C_INT_ERROR_MASK	(HSI2C_TX_UNDERRUN_EN |\
+				 HSI2C_TX_OVERRUN_EN  |\
+				 HSI2C_RX_UNDERRUN_EN |\
+				 HSI2C_RX_OVERRUN_EN  |\
+				 HSI2C_INT_TRAILING_EN)
+
+/* I2C_CONF Register bits */
+#define HSI2C_AUTO_MODE			(1u << 31)
+#define HSI2C_10BIT_ADDR_MODE		(1u << 30)
+#define HSI2C_HS_MODE			(1u << 29)
+
+/* I2C_AUTO_CONF Register bits */
+#define HSI2C_READ_WRITE		(1u << 16)
+#define HSI2C_STOP_AFTER_TRANS		(1u << 17)
+#define HSI2C_MASTER_RUN		(1u << 31)
+
+/* I2C_TIMEOUT Register bits */
+#define HSI2C_TIMEOUT_EN		(1u << 31)
+
+/* I2C_TRANS_STATUS register bits */
+#define HSI2C_MASTER_BUSY		(1u << 17)
+#define HSI2C_SLAVE_BUSY		(1u << 16)
+#define HSI2C_TIMEOUT_AUTO		(1u << 4)
+#define HSI2C_NO_DEV			(1u << 3)
+#define HSI2C_NO_DEV_ACK		(1u << 2)
+#define HSI2C_TRANS_ABORT		(1u << 1)
+#define HSI2C_TRANS_SUCCESS		(1u << 0)
+#define HSI2C_TRANS_ERROR_MASK	(HSI2C_TIMEOUT_AUTO |\
+				 HSI2C_NO_DEV | HSI2C_NO_DEV_ACK |\
+				 HSI2C_TRANS_ABORT)
+#define HSI2C_TRANS_FINISHED_MASK (HSI2C_TRANS_ERROR_MASK | HSI2C_TRANS_SUCCESS)
+
+
+/* I2C_FIFO_STAT Register bits */
+#define HSI2C_RX_FIFO_EMPTY		(1u << 24)
+#define HSI2C_RX_FIFO_FULL		(1u << 23)
+#define HSI2C_TX_FIFO_EMPTY		(1u << 8)
+#define HSI2C_TX_FIFO_FULL		(1u << 7)
+#define HSI2C_RX_FIFO_LEVEL(x)		(((x) >> 16) & 0x7f)
+#define HSI2C_TX_FIFO_LEVEL(x)		((x) & 0x7f)
+
+#define HSI2C_SLV_ADDR_MAS(x)		((x & 0x3ff) << 10)
+
+#define HSI2C_TIMEOUT_US 10000 /* 10 ms, finer granularity */
+
+/*
+ * Wait for transfer completion.
+ *
+ * This function reads the interrupt status register waiting for the INT_I2C
+ * bit to be set, which indicates copletion of a transaction.
+ *
+ * @param i2c: pointer to the appropriate register bank
+ *
+ * @return: I2C_OK in case of successful completion, I2C_NOK_TIMEOUT in case
+ *          the status bits do not get set in time, or an approrpiate error
+ *          value in case of transfer errors.
+ */
+static int hsi2c_wait_for_trx(struct exynos5_hsi2c *i2c)
+{
+	int i = HSI2C_TIMEOUT_US;
+
+	while (i-- > 0) {
+		u32 int_status = readl(&i2c->usi_int_stat);
+
+		if (int_status & HSI2C_INT_I2C_EN) {
+			u32 trans_status = readl(&i2c->usi_trans_status);
+
+			/* Deassert pending interrupt. */
+			writel(int_status, &i2c->usi_int_stat);
+
+			if (trans_status & HSI2C_NO_DEV_ACK) {
+				debug("%s: no ACK from device\n", __func__);
+				return I2C_NACK;
+			}
+			if (trans_status & HSI2C_NO_DEV) {
+				debug("%s: no device\n", __func__);
+				return I2C_NOK;
+			}
+			if (trans_status & HSI2C_TRANS_ABORT) {
+				debug("%s: arbitration lost\n", __func__);
+				return I2C_NOK_LA;
+			}
+			if (trans_status & HSI2C_TIMEOUT_AUTO) {
+				debug("%s: device timed out\n", __func__);
+				return I2C_NOK_TOUT;
+			}
+			return I2C_OK;
+		}
+		udelay(1);
+	}
+	debug("%s: transaction timeout!\n", __func__);
+	return I2C_NOK_TOUT;
+}
+
+static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus)
+{
+	struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
+	ulong clkin;
+	unsigned int op_clk = i2c_bus->clock_frequency;
+	unsigned int i = 0, utemp0 = 0, utemp1 = 0;
+	unsigned int t_ftl_cycle;
+
+#if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5)
+	clkin = get_i2c_clk();
+#else
+	clkin = get_PCLK();
+#endif
+	/* FPCLK / FI2C =
+	 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
+	 * uTemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
+	 * uTemp1 = (TSCLK_L + TSCLK_H + 2)
+	 * uTemp2 = TSCLK_L + TSCLK_H
+	 */
+	t_ftl_cycle = (readl(&hsregs->usi_conf) >> 16) & 0x7;
+	utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle;
+
+	/* CLK_DIV max is 256 */
+	for (i = 0; i < 256; i++) {
+		utemp1 = utemp0 / (i + 1);
+		if ((utemp1 < 512) && (utemp1 > 4)) {
+			i2c_bus->clk_cycle = utemp1 - 2;
+			i2c_bus->clk_div = i;
+			return 0;
+		}
+	}
+	return -EINVAL;
+}
+
+static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus)
+{
+	struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
+	unsigned int t_sr_release;
+	unsigned int n_clkdiv;
+	unsigned int t_start_su, t_start_hd;
+	unsigned int t_stop_su;
+	unsigned int t_data_su, t_data_hd;
+	unsigned int t_scl_l, t_scl_h;
+	u32 i2c_timing_s1;
+	u32 i2c_timing_s2;
+	u32 i2c_timing_s3;
+	u32 i2c_timing_sla;
+
+	n_clkdiv = i2c_bus->clk_div;
+	t_scl_l = i2c_bus->clk_cycle / 2;
+	t_scl_h = i2c_bus->clk_cycle / 2;
+	t_start_su = t_scl_l;
+	t_start_hd = t_scl_l;
+	t_stop_su = t_scl_l;
+	t_data_su = t_scl_l / 2;
+	t_data_hd = t_scl_l / 2;
+	t_sr_release = i2c_bus->clk_cycle;
+
+	i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
+	i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
+	i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0;
+	i2c_timing_sla = t_data_hd << 0;
+
+	writel(HSI2C_TRAILING_COUNT, &hsregs->usi_trailing_ctl);
+
+	/* Clear to enable Timeout */
+	clrsetbits_le32(&hsregs->usi_timeout, HSI2C_TIMEOUT_EN, 0);
+
+	/* set AUTO mode */
+	writel(readl(&hsregs->usi_conf) | HSI2C_AUTO_MODE, &hsregs->usi_conf);
+
+	/* Enable completion conditions' reporting. */
+	writel(HSI2C_INT_I2C_EN, &hsregs->usi_int_en);
+
+	/* Enable FIFOs */
+	writel(HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN, &hsregs->usi_fifo_ctl);
+
+	/* Currently operating in Fast speed mode. */
+	writel(i2c_timing_s1, &hsregs->usi_timing_fs1);
+	writel(i2c_timing_s2, &hsregs->usi_timing_fs2);
+	writel(i2c_timing_s3, &hsregs->usi_timing_fs3);
+	writel(i2c_timing_sla, &hsregs->usi_timing_sla);
+}
+
+/* SW reset for the high speed bus */
+static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus)
+{
+	struct exynos5_hsi2c *i2c = i2c_bus->hsregs;
+	u32 i2c_ctl;
+
+	/* Set and clear the bit for reset */
+	i2c_ctl = readl(&i2c->usi_ctl);
+	i2c_ctl |= HSI2C_SW_RST;
+	writel(i2c_ctl, &i2c->usi_ctl);
+
+	i2c_ctl = readl(&i2c->usi_ctl);
+	i2c_ctl &= ~HSI2C_SW_RST;
+	writel(i2c_ctl, &i2c->usi_ctl);
+
+	/* Initialize the configure registers */
+	hsi2c_ch_init(i2c_bus);
+}
+
+/*
+ * Poll the appropriate bit of the fifo status register until the interface is
+ * ready to process the next byte or timeout expires.
+ *
+ * In addition to the FIFO status register this function also polls the
+ * interrupt status register to be able to detect unexpected transaction
+ * completion.
+ *
+ * When FIFO is ready to process the next byte, this function returns I2C_OK.
+ * If in course of polling the INT_I2C assertion is detected, the function
+ * returns I2C_NOK. If timeout happens before any of the above conditions is
+ * met - the function returns I2C_NOK_TOUT;
+
+ * @param i2c: pointer to the appropriate i2c register bank.
+ * @param rx_transfer: set to True if the receive transaction is in progress.
+ * @return: as described above.
+ */
+static unsigned hsi2c_poll_fifo(struct exynos5_hsi2c *i2c, bool rx_transfer)
+{
+	u32 fifo_bit = rx_transfer ? HSI2C_RX_FIFO_EMPTY : HSI2C_TX_FIFO_FULL;
+	int i = HSI2C_TIMEOUT_US;
+
+	while (readl(&i2c->usi_fifo_stat) & fifo_bit) {
+		if (readl(&i2c->usi_int_stat) & HSI2C_INT_I2C_EN) {
+			/*
+			 * There is a chance that assertion of
+			 * HSI2C_INT_I2C_EN and deassertion of
+			 * HSI2C_RX_FIFO_EMPTY happen simultaneously. Let's
+			 * give FIFO status priority and check it one more
+			 * time before reporting interrupt. The interrupt will
+			 * be reported next time this function is called.
+			 */
+			if (rx_transfer &&
+			    !(readl(&i2c->usi_fifo_stat) & fifo_bit))
+				break;
+			return I2C_NOK;
+		}
+		if (!i--) {
+			debug("%s: FIFO polling timeout!\n", __func__);
+			return I2C_NOK_TOUT;
+		}
+		udelay(1);
+	}
+	return I2C_OK;
+}
+
+/*
+ * Preapre hsi2c transaction, either read or write.
+ *
+ * Set up transfer as described in section 27.5.1.2 'I2C Channel Auto Mode' of
+ * the 5420 UM.
+ *
+ * @param i2c: pointer to the appropriate i2c register bank.
+ * @param chip: slave address on the i2c bus (with read/write bit exlcuded)
+ * @param len: number of bytes expected to be sent or received
+ * @param rx_transfer: set to true for receive transactions
+ * @param: issue_stop: set to true if i2c stop condition should be generated
+ *         after this transaction.
+ * @return: I2C_NOK_TOUT in case the bus remained busy for HSI2C_TIMEOUT_US,
+ *          I2C_OK otherwise.
+ */
+static int hsi2c_prepare_transaction(struct exynos5_hsi2c *i2c,
+				     u8 chip,
+				     u16 len,
+				     bool rx_transfer,
+				     bool issue_stop)
+{
+	u32 conf;
+
+	conf = len | HSI2C_MASTER_RUN;
+
+	if (issue_stop)
+		conf |= HSI2C_STOP_AFTER_TRANS;
+
+	/* Clear to enable Timeout */
+	writel(readl(&i2c->usi_timeout) & ~HSI2C_TIMEOUT_EN, &i2c->usi_timeout);
+
+	/* Set slave address */
+	writel(HSI2C_SLV_ADDR_MAS(chip), &i2c->i2c_addr);
+
+	if (rx_transfer) {
+		/* i2c master, read transaction */
+		writel((HSI2C_RXCHON | HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
+		       &i2c->usi_ctl);
+
+		/* read up to len bytes, stop after transaction is finished */
+		writel(conf | HSI2C_READ_WRITE, &i2c->usi_auto_conf);
+	} else {
+		/* i2c master, write transaction */
+		writel((HSI2C_TXCHON | HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
+		       &i2c->usi_ctl);
+
+		/* write up to len bytes, stop after transaction is finished */
+		writel(conf, &i2c->usi_auto_conf);
+	}
+
+	/* Reset all pending interrupt status bits we care about, if any */
+	writel(HSI2C_INT_I2C_EN, &i2c->usi_int_stat);
+
+	return I2C_OK;
+}
+
+/*
+ * Wait while i2c bus is settling down (mostly stop gets completed).
+ */
+static int hsi2c_wait_while_busy(struct exynos5_hsi2c *i2c)
+{
+	int i = HSI2C_TIMEOUT_US;
+
+	while (readl(&i2c->usi_trans_status) & HSI2C_MASTER_BUSY) {
+		if (!i--) {
+			debug("%s: bus busy\n", __func__);
+			return I2C_NOK_TOUT;
+		}
+		udelay(1);
+	}
+	return I2C_OK;
+}
+
+static int hsi2c_write(struct exynos5_hsi2c *i2c,
+		       unsigned char chip,
+		       unsigned char addr[],
+		       unsigned char alen,
+		       unsigned char data[],
+		       unsigned short len,
+		       bool issue_stop)
+{
+	int i, rv = 0;
+
+	if (!(len + alen)) {
+		/* Writes of zero length not supported in auto mode. */
+		debug("%s: zero length writes not supported\n", __func__);
+		return I2C_NOK;
+	}
+
+	rv = hsi2c_prepare_transaction
+		(i2c, chip, len + alen, false, issue_stop);
+	if (rv != I2C_OK)
+		return rv;
+
+	/* Move address, if any, and the data, if any, into the FIFO. */
+	for (i = 0; i < alen; i++) {
+		rv = hsi2c_poll_fifo(i2c, false);
+		if (rv != I2C_OK) {
+			debug("%s: address write failed\n", __func__);
+			goto write_error;
+		}
+		writel(addr[i], &i2c->usi_txdata);
+	}
+
+	for (i = 0; i < len; i++) {
+		rv = hsi2c_poll_fifo(i2c, false);
+		if (rv != I2C_OK) {
+			debug("%s: data write failed\n", __func__);
+			goto write_error;
+		}
+		writel(data[i], &i2c->usi_txdata);
+	}
+
+	rv = hsi2c_wait_for_trx(i2c);
+
+ write_error:
+	if (issue_stop) {
+		int tmp_ret = hsi2c_wait_while_busy(i2c);
+		if (rv == I2C_OK)
+			rv = tmp_ret;
+	}
+
+	writel(HSI2C_FUNC_MODE_I2C, &i2c->usi_ctl); /* done */
+	return rv;
+}
+
+static int hsi2c_read(struct exynos5_hsi2c *i2c,
+		      unsigned char chip,
+		      unsigned char addr[],
+		      unsigned char alen,
+		      unsigned char data[],
+		      unsigned short len)
+{
+	int i, rv, tmp_ret;
+	bool drop_data = false;
+
+	if (!len) {
+		/* Reads of zero length not supported in auto mode. */
+		debug("%s: zero length read adjusted\n", __func__);
+		drop_data = true;
+		len = 1;
+	}
+
+	if (alen) {
+		/* Internal register adress needs to be written first. */
+		rv = hsi2c_write(i2c, chip, addr, alen, NULL, 0, false);
+		if (rv != I2C_OK)
+			return rv;
+	}
+
+	rv = hsi2c_prepare_transaction(i2c, chip, len, true, true);
+
+	if (rv != I2C_OK)
+		return rv;
+
+	for (i = 0; i < len; i++) {
+		rv = hsi2c_poll_fifo(i2c, true);
+		if (rv != I2C_OK)
+			goto read_err;
+		if (drop_data)
+			continue;
+		data[i] = readl(&i2c->usi_rxdata);
+	}
+
+	rv = hsi2c_wait_for_trx(i2c);
+
+ read_err:
+	tmp_ret = hsi2c_wait_while_busy(i2c);
+	if (rv == I2C_OK)
+		rv = tmp_ret;
+
+	writel(HSI2C_FUNC_MODE_I2C, &i2c->usi_ctl); /* done */
+	return rv;
+}
+
+static int exynos_hs_i2c_xfer(struct udevice *dev, struct i2c_msg *msg,
+			      int nmsgs)
+{
+	struct s3c24x0_i2c_bus *i2c_bus = dev_get_priv(dev);
+	struct exynos5_hsi2c *hsregs = i2c_bus->hsregs;
+	int ret;
+
+	for (; nmsgs > 0; nmsgs--, msg++) {
+		if (msg->flags & I2C_M_RD) {
+			ret = hsi2c_read(hsregs, msg->addr, 0, 0, msg->buf,
+					 msg->len);
+		} else {
+			ret = hsi2c_write(hsregs, msg->addr, 0, 0, msg->buf,
+					  msg->len, true);
+		}
+		if (ret) {
+			exynos5_i2c_reset(i2c_bus);
+			return -EREMOTEIO;
+		}
+	}
+
+	return 0;
+}
+
+static int s3c24x0_i2c_set_bus_speed(struct udevice *dev, unsigned int speed)
+{
+	struct s3c24x0_i2c_bus *i2c_bus = dev_get_priv(dev);
+
+	i2c_bus->clock_frequency = speed;
+
+	if (hsi2c_get_clk_details(i2c_bus))
+		return -EFAULT;
+	hsi2c_ch_init(i2c_bus);
+
+	return 0;
+}
+
+static int s3c24x0_i2c_probe(struct udevice *dev, uint chip, uint chip_flags)
+{
+	struct s3c24x0_i2c_bus *i2c_bus = dev_get_priv(dev);
+	uchar buf[1];
+	int ret;
+
+	buf[0] = 0;
+
+	/*
+	 * What is needed is to send the chip address and verify that the
+	 * address was <ACK>ed (i.e. there was a chip at that address which
+	 * drove the data line low).
+	 */
+	ret = hsi2c_read(i2c_bus->hsregs, chip, 0, 0, buf, 1);
+
+	return ret != I2C_OK;
+}
+
+static int s3c_i2c_ofdata_to_platdata(struct udevice *dev)
+{
+	const void *blob = gd->fdt_blob;
+	struct s3c24x0_i2c_bus *i2c_bus = dev_get_priv(dev);
+	int node;
+
+	node = dev->of_offset;
+
+	i2c_bus->hsregs = (struct exynos5_hsi2c *)dev_get_addr(dev);
+
+	i2c_bus->id = pinmux_decode_periph_id(blob, node);
+
+	i2c_bus->clock_frequency = fdtdec_get_int(blob, node,
+						  "clock-frequency", 100000);
+	i2c_bus->node = node;
+	i2c_bus->bus_num = dev->seq;
+
+	exynos_pinmux_config(i2c_bus->id, PINMUX_FLAG_HS_MODE);
+
+	i2c_bus->active = true;
+
+	return 0;
+}
+
+static const struct dm_i2c_ops exynos_hs_i2c_ops = {
+	.xfer		= exynos_hs_i2c_xfer,
+	.probe_chip	= s3c24x0_i2c_probe,
+	.set_bus_speed	= s3c24x0_i2c_set_bus_speed,
+};
+
+static const struct udevice_id exynos_hs_i2c_ids[] = {
+	{ .compatible = "samsung,exynos5-hsi2c" },
+	{ }
+};
+
+U_BOOT_DRIVER(hs_i2c) = {
+	.name	= "i2c_s3c_hs",
+	.id	= UCLASS_I2C,
+	.of_match = exynos_hs_i2c_ids,
+	.ofdata_to_platdata = s3c_i2c_ofdata_to_platdata,
+	.priv_auto_alloc_size = sizeof(struct s3c24x0_i2c_bus),
+	.ops	= &exynos_hs_i2c_ops,
+};

drivers/i2c/fti2c010.c

@@ -5,6 +5,9 @@
  * Dante Su <dantesu@faraday-tech.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/ihs_i2c.c

@@ -3,6 +3,9 @@
  * Dirk Eibach,  Guntermann & Drunck GmbH, eibach@gdsys.de
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/kona_i2c.c

@@ -2,6 +2,9 @@
  * Copyright 2013 Broadcom Corporation.
  *
  * SPDX-License-Identifier:      GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/lpc32xx_i2c.c

@@ -5,6 +5,9 @@
  * Written-by: Albert ARIBAUD - 3ADEV <albert.aribaud@3adev.fr>
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/pca9564_i2c.c

@@ -12,6 +12,9 @@
  * Bugs:
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/ppc4xx_i2c.c

@@ -8,6 +8,9 @@
  * Bill Hunter,  Wave 7 Optics, williamhunter@mediaone.net
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/rcar_i2c.c

@@ -5,6 +5,9 @@
  * Copyright (C) 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
  *
  * SPDX-License-Identifier: GPL-2.0
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/s3c24x0_i2c.h

@@ -59,4 +59,26 @@ struct s3c24x0_i2c_bus {
 	unsigned clk_cycle;
 	unsigned clk_div;
 };
+
+#define	I2C_WRITE	0
+#define I2C_READ	1
+
+#define I2C_OK		0
+#define I2C_NOK		1
+#define I2C_NACK	2
+#define I2C_NOK_LA	3	/* Lost arbitration */
+#define I2C_NOK_TOUT	4	/* time out */
+
+/* S3C I2C Controller bits */
+#define I2CSTAT_BSY	0x20	/* Busy bit */
+#define I2CSTAT_NACK	0x01	/* Nack bit */
+#define I2CCON_ACKGEN	0x80	/* Acknowledge generation */
+#define I2CCON_IRPND	0x10	/* Interrupt pending bit */
+#define I2C_MODE_MT	0xC0	/* Master Transmit Mode */
+#define I2C_MODE_MR	0x80	/* Master Receive Mode */
+#define I2C_START_STOP	0x20	/* START / STOP */
+#define I2C_TXRX_ENA	0x10	/* I2C Tx/Rx enable */
+
+#define I2C_TIMEOUT_MS 10		/* 10 ms */
+
 #endif /* _S3C24X0_I2C_H */

drivers/i2c/sh_i2c.c

@@ -3,6 +3,9 @@
  * Copyright (C) 2011, 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/sh_sh7734_i2c.c

@@ -3,6 +3,9 @@
  * Copyright (C) 2012 Renesas Solutions Corp.
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/soft_i2c.c

@@ -11,6 +11,9 @@
  * This has been changed substantially by Gerald Van Baren, Custom IDEAS,
  * vanbaren@cideas.com.  It was heavily influenced by LiMon, written by
  * Neil Russell.
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

drivers/i2c/tsi108_i2c.c

@@ -3,6 +3,9 @@
  * Author: Alex Bounine
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <config.h>

drivers/i2c/zynq_i2c.c

@@ -8,6 +8,9 @@
  * Copyright (c) 2012-2013 Xilinx, Michal Simek
  *
  * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * NOTE: This driver should be converted to driver model before June 2017.
+ * Please see doc/driver-model/i2c-howto.txt for instructions.
  */
 
 #include <common.h>

include/configs/s5p_goni.h

@@ -229,25 +229,6 @@
 
 #define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_LOAD_ADDR - 0x1000000)
 
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_MAX8998
-
-#include <asm/arch/gpio.h>
-/*
- * I2C Settings
- */
-#define CONFIG_SOFT_I2C_GPIO_SCL S5PC110_GPIO_J43
-#define CONFIG_SOFT_I2C_GPIO_SDA S5PC110_GPIO_J40
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_I2C_INIT_BOARD
-
-#define CONFIG_SYS_MAX_I2C_BUS	7
 #define CONFIG_USB_GADGET_DWC2_OTG_PHY
 #define CONFIG_USB_FUNCTION_MASS_STORAGE
 

include/configs/s5pc210_universal.h

@@ -153,25 +153,6 @@
 #define CONFIG_SAMSUNG_ONENAND
 #define CONFIG_SYS_ONENAND_BASE		0x0C000000
 
-#include <asm/arch/gpio.h>
-/*
- * I2C Settings
- */
-#define CONFIG_SOFT_I2C_GPIO_SCL EXYNOS4_GPIO_B7
-#define CONFIG_SOFT_I2C_GPIO_SDA EXYNOS4_GPIO_B6
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0
-#define CONFIG_SOFT_I2C_READ_REPEATED_START
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS	7
-
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_MAX8998
-
 #define CONFIG_USB_GADGET_DWC2_OTG_PHY
 
 /*

include/configs/trats.h

@@ -178,36 +178,6 @@
 /* GPT */
 #define CONFIG_RANDOM_UUID
 
-/* I2C */
-#include <asm/arch/gpio.h>
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_S3C24X0
-#define CONFIG_SYS_I2C_S3C24X0_SPEED	100000
-#define CONFIG_SYS_I2C_S3C24X0_SLAVE	0xFE
-#define CONFIG_MAX_I2C_NUM		8
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
-#define CONFIG_SOFT_I2C_READ_REPEATED_START
-#define CONFIG_SYS_I2C_INIT_BOARD
-
-/* I2C FG */
-#define CONFIG_SOFT_I2C_GPIO_SCL EXYNOS4_GPIO_Y41
-#define CONFIG_SOFT_I2C_GPIO_SDA EXYNOS4_GPIO_Y40
-
-/* POWER */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_MAX8997
-
-#define CONFIG_POWER_FG
-#define CONFIG_POWER_FG_MAX17042
-#define CONFIG_POWER_MUIC
-#define CONFIG_POWER_MUIC_MAX8997
-#define CONFIG_POWER_BATTERY
-#define CONFIG_POWER_BATTERY_TRATS
-
 /* Security subsystem - enable hw_rand() */
 #define CONFIG_EXYNOS_ACE_SHA
 #define CONFIG_LIB_HW_RAND

include/configs/trats2.h

@@ -155,39 +155,6 @@
 /* GPT */
 #define CONFIG_RANDOM_UUID
 
-/* I2C */
-#include <asm/arch/gpio.h>
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_S3C24X0
-#define CONFIG_SYS_I2C_S3C24X0_SPEED	100000
-#define CONFIG_SYS_I2C_S3C24X0_SLAVE	0
-#define CONFIG_MAX_I2C_NUM		8
-#define CONFIG_SYS_I2C_SOFT
-#define CONFIG_SYS_I2C_SOFT_SPEED	50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x00
-#define I2C_SOFT_DECLARATIONS2
-#define CONFIG_SYS_I2C_SOFT_SPEED_2     50000
-#define CONFIG_SYS_I2C_SOFT_SLAVE_2     0x00
-#define CONFIG_SOFT_I2C_READ_REPEATED_START
-#define CONFIG_SYS_I2C_INIT_BOARD
-
-#ifndef __ASSEMBLY__
-int get_soft_i2c_scl_pin(void);
-int get_soft_i2c_sda_pin(void);
-#endif
-#define CONFIG_SOFT_I2C_GPIO_SCL	get_soft_i2c_scl_pin()
-#define CONFIG_SOFT_I2C_GPIO_SDA	get_soft_i2c_sda_pin()
-
-/* POWER */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_MAX77686
-#define CONFIG_POWER_PMIC_MAX77693
-#define CONFIG_POWER_MUIC_MAX77693
-#define CONFIG_POWER_FG_MAX77693
-#define CONFIG_POWER_BATTERY_TRATS2
-
 /* Security subsystem - enable hw_rand() */
 #define CONFIG_EXYNOS_ACE_SHA
 #define CONFIG_LIB_HW_RAND