This update brings the ALPR board support to the newest version.
It also fixes a problem with the NAND driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
- fix a typo in V38B config file
- move watchdog initialisation earlier in the boot process
- add "wdt=off" to default kernel command line (disables kernel watchdog)
multiplier table can not refect the real PLL clock behavior of these
processors. Please refer to the hardware specification for detailed
information of the corresponding processors.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The original search_one_table() function code can only processes the search
for the exception occurring in FLASH/ROM, because the exception and fixup
table usually locate in FLASH. If the exception address is also in
FLASH, it will be OK.
If the exception occurs in RAM, after the u-boot relocation, a
relocation offset should be added.
clean up the code in cpu/74xx_7xx/cpu.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
(1) remove some C++ comments.
(2) remove trailing white space.
(3) remove trailing empty line.
(4) Indentation by table.
(5) remove {} in one line condition.
(6) add space before '(' in function call.
Remove some weird printf () output.
Add necessary comments.
Modified Makefile to support building in a separate directory.
The soc node of the mpc52xx needs to be loaded with the IPB bus frequency,
not the XLB frequency.
This patch depends on the previous patches for MPC52xx device tree support
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Signed-off-by: Stefan Roese <sr@denx.de>
In the bootvx command the load address was only read from the env
variable "loadaddr" and not optionally passed as paramter as described
in the help. This is fixed with this patch. The behaviour is now the
same as in the bootelf command.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixed include/ppc440.c for UIC address Bug
Corrects bug affecting the addresses for the universal interrupt
controller UIC2 and UIC3 on the PPC440 Epx, GRx, and SPE chips.
Signed-off-by: Jeff Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese
roy zang
Wolfgang Denk
Bartlomiej Sieka
Wolfgang Denk
Stefano Babic
Heiko Schocher
Andrei Safronov
Grant Likely
Joakim Tjernlund
Kim Phillips
Timur Tabi