FIX: syntax error in uboot environment

BugzId: 56824

arch/arm/Kconfig

@@ -398,6 +398,14 @@ config TARGET_AM335X_NRHW20
         select DM_SERIAL
         select DM_GPIO
 
+config TARGET_AM335X_NRHW22
+        bool "Support am335x_nrhw22"
+        select CPU_V7
+        select SUPPORT_SPL
+        select DM
+        select DM_SERIAL
+        select DM_GPIO
+
 config TARGET_AM335X_SL50
 	bool "Support am335x_sl50"
 	select CPU_V7
@@ -897,6 +905,7 @@ source "board/mpl/vcma9/Kconfig"
 source "board/nm/netbird/Kconfig"
 source "board/nm/netbird_v2/Kconfig"
 source "board/nm/nrhw20/Kconfig"
+source "board/nm/nrhw22/Kconfig"
 source "board/olimex/mx23_olinuxino/Kconfig"
 source "board/phytec/pcm051/Kconfig"
 source "board/phytec/pcm052/Kconfig"

arch/arm/include/asm/arch-am33xx/spl.h

@@ -47,6 +47,7 @@
 #define BOOT_DEVICE_UART	0x41
 #define BOOT_DEVICE_USBETH	0x44
 #define BOOT_DEVICE_CPGMAC	0x46
+#define BOOT_DEVICE_JTAG        0x58
 
 #define MMC_BOOT_DEVICES_START	BOOT_DEVICE_MMC1
 #define MMC_BOOT_DEVICES_END	BOOT_DEVICE_MMC2

board/nm/netbird/board.c

@@ -400,7 +400,7 @@ int board_late_init(void)
 		boot_partition = 0;
 	}
 
-	/* mmcblk0p1 => root0, mmcblk0p2 => root1 so +1 */
+	/* mmcblk1p1 => root0, mmcblk1p2 => root1 so +1 */
 	setenv_ulong("root_part", boot_partition + 1);
 
 	check_reset_button();

board/nm/netbird_v2/board.c

@@ -665,7 +665,7 @@ int board_late_init(void)
 		boot_partition = 0;
 	}
 
-	/* mmcblk0p1 => root0, mmcblk0p2 => root1 so +1 */
+	/* mmcblk1p1 => root0, mmcblk1p2 => root1 so +1 */
 	setenv_ulong("root_part", boot_partition + 1);
 
 	check_reset_button();

board/nm/nrhw20/board.c

@@ -32,6 +32,7 @@
 #include <cpsw.h>
 #include <environment.h>
 #include <watchdog.h>
+#include <libfdt.h>
 
 #include "../common/bdparser.h"
 #include "../common/board_descriptor.h"
@@ -232,6 +233,18 @@ static void set_indicator(unsigned led, int red, int green)
 	i2c_set_bus_num(old_bus);
 }
 
+static bool is_jtag_boot(uint32_t address)
+{
+	char* jtag_token = (char*)address;
+	if (strcmp(jtag_token, "JTAGBOOT") == 0) {
+		strcpy(jtag_token, "jtagboot");
+		return true;
+	}
+	else {
+		return false;
+	}
+}
+
 /*
  * Read header information from EEPROM into global structure.
  */
@@ -241,18 +254,23 @@ static inline int __maybe_unused read_eeprom(void)
 }
 
 /* Selects console for SPL.
- * U-Boot console is defined by CONFIG_CONS_INDEX (via menuconfig)
+ * U-Boot console is defined by CONSOLE_INDEX variable 
+ * defined using serial_set_console_index(int index)
  */
 struct serial_device *default_serial_console(void)
 {
-	if (spl_boot_device() == BOOT_DEVICE_UART) {
+	/* Mux Pins for selected UART properly. 
+	   Note: uart indexes start at 0 while 
+	   eserial indexes start at 1. */
+	if ((spl_boot_device() == BOOT_DEVICE_UART) || 
+		(spl_boot_device() == BOOT_DEVICE_JTAG)) {
 		enable_uart0_pin_mux();
 		return &eserial1_device;
+	} else {
+		/* Use bluetooth uart, if no ouput shall be seen. */
+		enable_uart5_pin_mux();
+		return &eserial6_device;
 	}
-	else {
-		enable_uart1_pin_mux();
-		return &eserial2_device;
-    }
 }
 
 #ifndef CONFIG_SKIP_LOWLEVEL_INIT
@@ -323,6 +341,14 @@ void am33xx_spl_board_init(void)
 
 	/* Set MPU Frequency to what we detected now that voltages are set */
 	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+
+	/* Debugger can place marker at end of SRAM to stop boot here */
+	if (is_jtag_boot(CONFIG_JTAG_MARKER_SPL))
+	{
+		puts("Detected JTAG boot, executing bkpt #0\n");
+
+		__asm__ __volatile__ ("bkpt #0");
+	}
 }
 
 const struct dpll_params *get_dpll_ddr_params(void)
@@ -520,43 +546,61 @@ int board_init(void)
 
 #if !defined(CONFIG_SPL_BUILD)
 
-// TODO: Check tty logic with NRSW team
+extern int console_init_f(void);
-//  UART1: Fixed to mains connector, always present
+extern void serial_set_console_index(int index);
-//  UART0: Mapped to shield slot
+
-//         Can only be used when shield is installed
+/*
+ * Set Linux console based on
+ * - Selection in /root/boot/consoledev
+ * - Available tty interfaces
+ *   - ttyS1: standard console (default)
+ *   - ttyS0: COM/IO shield (or used as console by kernel, 
+ *            when no other console available)
+ *   - ttyNull0: Dummy device if no real UART is available
+ */
 void set_console(void)
 {
-#if 0
-	int shield_id = bd_get_shield(0);
-	char buf[8];
-#endif
 	const char *defaultconsole = getenv("defaultconsole");
+	char buf[20];
+	int i;
 
+	/* Set default console to ttyS1 if not yet defined in env */
 	if (defaultconsole == 0) {
-		/* Use the default console */
 		setenv("defaultconsole", "ttyS1");
 	}
 
-#if 0
+	/* If consoledev file is present, take the tty defined in it as console */
-	/* Don't allow changing to ttyS0 because ttyS0 is not available in the
+	if (read_file("/root/boot/consoledev",buf, sizeof(buf)) > 3) {
-	 * kernel if no comio shield is available */
+		if (strstr(buf, "tty") == buf) {
-	if (shield_id != SHIELD_COM_IO) {
+			buf[sizeof(buf)-1] = 0;
-		return;
+			for (i=0; i<sizeof(buf); i++) {
+				if (buf[i]<=' ') {
+					buf[i] = 0;
+					break;
+				}
+			}
+			setenv("defaultconsole", buf);
+		}
 	}
 	
-	/* With comio shield the defaultconsole should be ttyS0 and not ttyS1 */
+#if defined(CONFIG_PRE_CONSOLE_BUFFER)
-	setenv("defaultconsole", "ttyS0");
+	defaultconsole = getenv("defaultconsole");
 
-	/* If consoledev is set, take this as productive console instead of default console */
+	if (strstr(defaultconsole, "ttyS0")) {
-	if (read_file("/root/boot/consoledev", buf, 5) != 5) {
+		/* Only use internal console, if explicitely specified */
-		puts("Invalid file consoledev\n");
+		serial_set_console_index(0);
-		return;
+//	} else if (strstr(defaultconsole, "ttyNull")) {
-	}
+//		/* If no console shall be available use bluetooth uart. */
-
+//		serial_set_console_index(5);
-	if (strstr(buf, "tty")==buf) {
+	} else {
-		buf[5] = 0;
+		/* Otherwise and especially, if no console is specified 
-		setenv("defaultconsole", buf);
+		use the default console, which is the external console */
+		serial_set_console_index(1);
 	}
+	serial_init(); /* serial communications setup */
+	console_init_f(); /* stage 1 init of console */
+#else
+    serial_set_console_index(1);
 #endif
 }
 
@@ -583,7 +627,7 @@ static void set_root_partition(void)
 		boot_partition = 0;
 	}
 
-	/* mmcblk0p1 => root0, mmcblk0p2 => root1 so +1 */
+	/* mmcblk1p1 => root0, mmcblk1p2 => root1 so +1 */
 	setenv_ulong("root_part", boot_partition + 1);
 }
 
@@ -624,16 +668,10 @@ static void check_fct(void)
 }
 
 
-static void set_fdtshieldcmd(const char *fdt_cmd)
-{
-	setenv("fdtshieldcmd", fdt_cmd);
-}
-
 struct shield_command {
 	int shield_id;
 	const char *name;
 	const char *default_shieldcmd;
-	const char *fdtshieldcmd;
 	void (*init)(void);
 };
 
@@ -642,18 +680,12 @@ static struct shield_command known_shield_commands[] = {
 		SHIELD_COM_IO,
 		"comio",
 		"shield comio mode rs232",
-		"fdt get value serial0 /aliases serial0;" \
-		"fdt set $serial0 status okay",
 		comio_shield_init
 	},
 	{
 		SHIELD_DUALCAN,
 		"dualcan",
 		"shield dualcan termination off off",
-		"fdt get value can0 /aliases d_can0;" \
-		"fdt get value can1 /aliases d_can1;" \
-		"fdt set $can0 status okay;" \
-		"fdt set $can1 status okay;",
 		can_shield_init
 	},
 };
@@ -692,7 +724,7 @@ static void shield_config(void)
 		return;
 	}
 
-	printf("Shield: %s\n", cmd->name);
+	printf("Shield:%s\n", cmd->name);
 
 	cmd->init();
 	shieldcmd = cmd->default_shieldcmd;
@@ -707,8 +739,6 @@ static void shield_config(void)
 	}
 
 	setenv("shieldcmd", shieldcmd);
-
-	set_fdtshieldcmd(cmd->fdtshieldcmd);
 }
 
 static void shield_init(void)
@@ -725,15 +755,20 @@ static bool get_button_state(void)
 	return (state & 0x01) == 0x01;
 }
 
-static void blink_led(void)
+static void blink_led(int red)
 {
+	int i;
 	const int pulse_width = 400*1000; /* 400ms */
 
 	/* Assumes green status LED is on */
 	udelay(pulse_width);
-	set_status_led(0, 0);
+	set_status_led(red, 1-red);
+	for (i=0; i<5; i++)
+		set_indicator(i, red, 1-red);
 	udelay(pulse_width);
 	set_status_led(0, 1);
+	for (i=0; i<5; i++)
+		set_indicator(i, 0, 0);
 }
 
 static void check_reset_button(void)
@@ -750,12 +785,11 @@ static void check_reset_button(void)
 
 		if (counter == 2000) {
 			/* Indicate factory reset threshold */
-			blink_led();
+			blink_led(0);
 		}
 		else if (counter == 12000) {
 			/* Indicate recovery boot threshold */
-			blink_led();
+			blink_led(1);
-			blink_led();
 		}
 	} while (counter < 12000);
 
@@ -783,13 +817,25 @@ static void check_reset_button(void)
 
 		printf("Booting recovery image...\n");
 
+		/* Set consoledev to external port */
+		setenv("defaultconsole", "ttyS1");
+
 		/* Set bootcmd to run recovery */
 		setenv("bootcmd", "run recovery");
-
-		/* set consoledev to external port */
-		/* setenv("consoledev", "ttyS1"); */
 	}
 }
+
+static void check_jtag_boot(void)
+{
+	if (is_jtag_boot(CONFIG_JTAG_MARKER_UBOOT)) {
+		char *bootcmd = getenv("bootcmd");
+		setenv ("bootcmd", "");
+		/* Save original bootcmd in "bc" to allow manual boot */
+		setenv ("bc", bootcmd);
+		puts("Detected JTAG boot. Waiting on command line\n");
+	}
+}
+
 #endif /* !defined(CONFIG_SPL_BUILD) */
 
 
@@ -822,10 +868,11 @@ int board_late_init(void)
 	set_console();
 	shield_init();
 
-	set_status_led(0, 1);	/* Green */
+	set_status_led(0, 0);	/* WAN led off */
 	set_indicator(0, 0, 1); /* Green */
 
 	check_fct();
+	check_jtag_boot();
 #endif
 
 	return 0;
@@ -948,3 +995,72 @@ int board_fit_config_name_match(const char *name)
 	return 0;
 }
 #endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+
+static void ft_enable_node(void* blob, const char* name)
+{
+	int node_ofs = -1;
+
+	node_ofs = fdt_path_offset(blob, name);
+	if (node_ofs >= 0) {
+		fdt_setprop_string(blob, node_ofs, "status", "okay");
+	}
+}
+
+static void ft_dio(void *blob, int shield_type)
+{
+	switch (shield_type) {
+		/* If COM/IO shield is present enable its I/Os */
+		case SHIELD_COM_IO:
+			ft_enable_node(blob, "/netbox_dio_comio");
+			break;
+
+		default:
+			ft_enable_node(blob, "/netbox_dio_default");
+			break;
+	}
+}
+
+static void ft_serial(void *blob, int shield_type)
+{
+	switch (shield_type) {
+		/* Enable uart1 (ttyS0) always as kernel needs it as fallback
+			console, if (ttyS1) is not available as console. */
+
+		default:
+			/* TODO: Should use alias serial0 */
+			ft_enable_node(blob, "/ocp/serial@44e09000");
+			break;
+	}
+}
+
+static void ft_dcan(void *blob, int shield_type)
+{
+	switch (shield_type) {
+		/* If Dual CAN shield is present enable dcan0, dcan1N1 */
+		case SHIELD_DUALCAN:
+		/* TODO: Should use alias d_can0, d_can1 */
+			ft_enable_node(blob, "/ocp/can@481cc000");
+			ft_enable_node(blob, "/ocp/can@481d0000");
+			break;
+
+		default:
+			break;
+	}
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	int shield_type = -1;
+
+	shield_type = bd_get_shield(0);
+
+	ft_dio(blob, shield_type);
+	ft_serial(blob, shield_type);
+	ft_dcan(blob, shield_type);
+
+	return 0;
+}
+
+#endif

board/nm/nrhw20/board.h

@@ -19,6 +19,8 @@
 void enable_uart0_pin_mux(void);
 void disable_uart0_pin_mux(void);
 void enable_uart1_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart5_pin_mux(void);
 /*
 void enable_uart2_pin_mux(void);
 void enable_uart3_pin_mux(void);

board/nm/nrhw20/fileaccess.c

@@ -1,6 +1,7 @@
 #include <common.h>
 #include <fs.h>
 
+#define BLOCK_DEVICE "mmc"
 #define OVERLAY_PART "1:3"
 
 int read_file(const char* filename, char *buf, int size)
@@ -9,14 +10,12 @@ int read_file(const char* filename, char *buf, int size)
 	loff_t len;
 	int ret;
 
-	/* If consoldev is set take this as productive conosle instead of default console */
+	if (fs_set_blk_dev(BLOCK_DEVICE, OVERLAY_PART, FS_TYPE_EXT) != 0) {
-	if (fs_set_blk_dev("mmc", OVERLAY_PART, FS_TYPE_EXT) != 0) {
 		puts("Error, can not set blk device\n");
 		return -1;
 	}
 
-
+	/* Read at most file size bytes */
-	/* File does not exist, do not print an error message */
 	if (fs_size(filename, &filesize)) {
 		return -1;
 	}
@@ -24,13 +23,12 @@ int read_file(const char* filename, char *buf, int size)
 	if (filesize < size)
 		size = filesize;
 
-	/* If consoldev is set take this as productive conosle instead of default console */
+	/* For very unclear reasons the block device needs to be set again after the call to fs_size() */
-	if (fs_set_blk_dev("mmc", OVERLAY_PART, FS_TYPE_EXT) != 0) {
+	if (fs_set_blk_dev(BLOCK_DEVICE, OVERLAY_PART, FS_TYPE_EXT) != 0) {
 		puts("Error, can not set blk device\n");
 		return -1;
 	}
 
-
 	if ((ret = fs_read(filename, (ulong)buf, 0, size, &len))) {
 		printf("Can't read file %s (size %d, len %lld, ret %d)\n", filename, size, len, ret);
 		return -1;

board/nm/nrhw20/mux.c

@@ -249,3 +249,12 @@ void enable_uart1_pin_mux(void)
 	configure_module_pin_mux(uart1_pin_mux);
 }
 
+void enable_uart3_pin_mux(void)
+{
+	configure_module_pin_mux(uart3_pin_mux);
+}
+
+void enable_uart5_pin_mux(void)
+{
+	configure_module_pin_mux(uart5_pin_mux);
+}

board/nm/nrhw22/Kconfig

@@ -0,0 +1,26 @@
+if TARGET_AM335X_NRHW22
+
+config SYS_BOARD
+        default "nrhw22"
+
+config SYS_VENDOR
+        default "nm"
+
+config SYS_SOC
+        default "am33xx"
+
+config SYS_CONFIG_NAME
+        default "am335x_nrhw22"
+
+config CONS_INDEX
+        int "UART used for console"
+        range 1 6
+        default 2
+        help
+          The AM335x SoC has a total of 6 UARTs (UART0 to UART5 as referenced
+          in documentation, etc) available to it.  Depending on your specific
+          board you may want something other than UART0 as for example the IDK
+          uses UART3 so enter 4 here.
+
+endif
+

board/nm/nrhw22/Makefile

@@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),)
+obj-y	:= mux.o
+endif
+
+obj-y	+= board.o ../common/bdparser.o ../common/board_descriptor.o fileaccess.o da9063.o

board/nm/nrhw22/board.c

@@ -0,0 +1,715 @@
+/*
+ * board.c
+ *
+ * Board functions for Netmodule NRHW 20, based on AM335x EVB
+ *
+ * Copyright (C) 2018 NetModule AG - http://www.netmodule.com/
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <serial.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/clk_synthesizer.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <pca953x.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <environment.h>
+#include <watchdog.h>
+#include <libfdt.h>
+
+#include "../common/bdparser.h"
+#include "../common/board_descriptor.h"
+#include "board.h"
+#include "da9063.h"
+#include "fileaccess.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+
+/*
+ * CPU GPIOs
+ *
+ * GPIO0_2: RST_GNSS~
+ * GPIO0_5: EXTINT_GNSS
+ * GPIO0_6: TIMEPULSE_GNSS
+ *
+ * GPIO0_16: RST_PHY~
+ * GPIO0_17: PMIC FAULT
+ *
+ */
+
+#define GPIO_TO_PIN(bank, gpio)		(32 * (bank) + (gpio))
+
+#define NETBIRD_GPIO_RST_PHY_N		GPIO_TO_PIN(0, 16)
+#define NETBIRD_GPIO_RST_USB_HUB_N	GPIO_TO_PIN(3, 21)
+
+#define NETBIRD_GPIO_RST_GNSS		GPIO_TO_PIN(0, 2)
+#define NETBIRD_GPIO_RST_PCI		GPIO_TO_PIN(3, 10)
+
+#define NETBIRD_GPIO_RST_GSM		GPIO_TO_PIN(1, 25)
+#define NETBIRD_GPIO_PWR_GSM		GPIO_TO_PIN(1, 21)
+#define NETBIRD_GPIO_WAKE_GSM		GPIO_TO_PIN(0, 31)
+#define NETBIRD_GPIO_SIM_SEL		GPIO_TO_PIN(3, 17)
+
+#define NETBIRD_GPIO_WLAN_EN		GPIO_TO_PIN(1, 26)
+#define NETBIRD_GPIO_BT_EN		GPIO_TO_PIN(1, 20)
+
+#define NETBIRD_GPIO_DIG_OUT		GPIO_TO_PIN(1, 14)
+#define NETBIRD_GPIO_DIG_IN		GPIO_TO_PIN(1, 15)
+
+#define NETBIRD_GPIO_PCI_WDIS		GPIO_TO_PIN(3, 9)
+
+
+/*
+ * PMIC GPIOs
+ *
+ * GPIO_7: EN_SUPPLY_GSM
+ * GPIO_8: VOLTAGE_SEL_PCIe
+ * GPIO_9: EN_SUPPLY_PCIe
+ * GPIO_10: LED0.RD~
+ * GPIO_11: LED0.GN~
+ */
+
+#define PMIC_GSM_SUPPLY_EN_IO		7
+#define PMIC_PCIe_SUPPLY_VSEL_IO	8
+#define PMIC_PCIe_SUPPLY_EN_IO		9
+#define PMIC_LED0_BLUE			10
+#define PMIC_LED0_GREEN			11
+
+#define DDR3_CLOCK_FREQUENCY		(400)
+
+#if !defined(CONFIG_SPL_BUILD)
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+#endif
+
+#define I2C_BD_EEPROM_BUS		(2)
+#define BD_EEPROM_ADDR			(0x50)	  /* CPU BD EEPROM (8kByte) is at 50 (A0) */
+#define BD_ADDRESS			(0x0000)  /* Board descriptor at beginning of EEPROM */
+#define PD_ADDRESS			(0x0200)  /* Product descriptor */
+#define PARTITION_ADDRESS		(0x0600)  /* Partition Table */
+
+static BD_Context   bdctx[3];		/* The descriptor contexts */
+
+
+static void init_i2c(void)
+{
+	i2c_set_bus_num(0);
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(2);
+	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
+}
+
+static int _bd_init(void)
+{
+	int old_bus;
+
+	old_bus = i2c_get_bus_num();
+	i2c_set_bus_num(I2C_BD_EEPROM_BUS);
+
+	if (bd_get_context(&bdctx[0], BD_EEPROM_ADDR, BD_ADDRESS) != 0) {
+		printf("%s() no valid bd found\n", __func__);
+		return -1;
+	}
+
+	if (bd_get_context(&bdctx[1], BD_EEPROM_ADDR, PD_ADDRESS) != 0) {
+		printf("%s() no valid pd found (legacy support)\n", __func__);
+		return -1;
+	}
+
+	if (bd_get_context(&bdctx[2], BD_EEPROM_ADDR, PARTITION_ADDRESS) != 0) {
+		printf("%s() no valid partition table found\n", __func__);
+		return -1;
+	}
+
+	bd_register_context_list(bdctx, ARRAY_SIZE(bdctx));
+
+	i2c_set_bus_num(old_bus);
+
+	return 0;
+}
+
+static bool is_jtag_boot(uint32_t address)
+{
+	char* jtag_token = (char*)address;
+	if (strcmp(jtag_token, "JTAGBOOT") == 0) {
+		strcpy(jtag_token, "jtagboot");
+		return true;
+	}
+	else {
+		return false;
+	}
+}
+
+/*
+ * Read header information from EEPROM into global structure.
+ */
+static inline int __maybe_unused read_eeprom(void)
+{
+	return _bd_init();
+}
+
+/* Selects console for SPL.
+ * U-Boot console is defined by CONSOLE_INDEX variable 
+ * defined using serial_set_console_index(int index)
+ */
+struct serial_device *default_serial_console(void)
+{
+	return &eserial1_device;
+}
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+
+static const struct ddr_data ddr3_netbird_data = {
+	/* Ratios were optimized by DDR3 training software from TI */
+	.datardsratio0 = 0x39,
+	.datawdsratio0 = 0x3f,
+	.datafwsratio0 = 0x98,
+	.datawrsratio0 = 0x7d,
+};
+
+static const struct cmd_control ddr3_netbird_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = 0x61A,	/* 32ms > 85°C */
+	.sdram_tim1 = 0x0AAAE51B,
+	.sdram_tim2 = 0x246B7FDA,
+	.sdram_tim3 = 0x50FFE67F,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+
+#define OSC	(V_OSCK/1000000)
+
+struct dpll_params dpll_ddr_nrhw22 = {
+	DDR3_CLOCK_FREQUENCY, OSC-1, 1, -1, -1, -1, -1
+};
+
+
+void am33xx_spl_board_init(void)
+{
+	/* Set CPU speed to 600 MHz (fix) */
+	dpll_mpu_opp100.m = MPUPLL_M_600;
+
+	/* Set CORE Frequencies to OPP100 (600MHz) */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* Configure both I2C buses used in NRHW22 */
+	init_i2c();
+
+	/* Configure default PMIC current limits. Will be overridden in Linux.
+	 * MEM   = 1.5A (0.55A)
+	 * IO    = 1.5A (0.5A)
+	 * PERI  = 2.0A (1.0A)
+	 * PRO   = 0.5A (unused)
+	 * CORE2 = 2.0A (0.55A)
+	 * CORE1 = 2.0A (0.25A, seems too low)
+	 */
+	da9063_init(CONFIG_PMIC_I2C_BUS);
+	da9063_set_reg(PMIC_REG_BUCK_ILIM_A, 0x00);
+	da9063_set_reg(PMIC_REG_BUCK_ILIM_B, 0x50);
+	da9063_set_reg(PMIC_REG_BUCK_ILIM_C, 0xFF);
+
+	/* Set MPU Frequency to what we detected now that voltages are set */
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+
+	/* Debugger can place marker at end of SRAM to stop boot here */
+	if (is_jtag_boot(CONFIG_JTAG_MARKER_SPL))
+	{
+		puts("Detected JTAG boot, executing bkpt #0\n");
+
+		__asm__ __volatile__ ("bkpt #0");
+	}
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	dpll_ddr_nrhw22.n = (get_osclk() / 1000000) - 1;
+	return &dpll_ddr_nrhw22;
+}
+
+void set_uart_mux_conf(void)
+{
+	enable_uart0_pin_mux();
+	enable_uart1_pin_mux();
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+
+const struct ctrl_ioregs ioregs_netbird = {
+	.cm0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+
+void sdram_init(void)
+{
+	config_ddr(DDR3_CLOCK_FREQUENCY, &ioregs_netbird,
+		   &ddr3_netbird_data,
+		   &ddr3_netbird_cmd_ctrl_data,
+		   &ddr3_emif_reg_data, 0);
+}
+
+#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
+
+#if !defined(CONFIG_SPL_BUILD)
+
+static void request_and_set_gpio(int gpio, const char *name, int value)
+{
+	int ret;
+
+	ret = gpio_request(gpio, name);
+	if (ret < 0) {
+		printf("%s: Unable to request %s\n", __func__, name);
+		return;
+	}
+
+	/* TODO: Set value here, remove later call gpio_set_value */
+	ret = gpio_direction_output(gpio, 0);
+	if (ret < 0) {
+		printf("%s: Unable to set %s as output\n", __func__, name);
+		goto err_free_gpio;
+	}
+
+	gpio_set_value(gpio, value);
+
+	return;
+
+err_free_gpio:
+	gpio_free(gpio);
+}
+
+#define REQUEST_AND_SET_GPIO(N)		request_and_set_gpio(N, #N, 1);
+#define REQUEST_AND_CLEAR_GPIO(N)	request_and_set_gpio(N, #N, 0);
+
+#endif
+
+
+
+static void set_status_led(int blue, int green)
+{
+	/* LED outputs are active low, invert state */
+	da9063_set_gpio(PMIC_LED0_BLUE, !blue);
+	da9063_set_gpio(PMIC_LED0_GREEN, !green);
+}
+
+#if !defined(CONFIG_SPL_BUILD)
+
+static void init_ethernet_switch(void)
+{
+	REQUEST_AND_CLEAR_GPIO(NETBIRD_GPIO_RST_PHY_N);
+	mdelay(1);
+
+	/* OMAP3 does not feature open drain pins, thus configure pin as input */
+	gpio_direction_input(NETBIRD_GPIO_RST_PHY_N);
+
+	/* When the Ethernet switch senses reset, it drives reset for 8..14ms
+	 * Wait longer than this time to avoid IO congestion later on.
+	 */
+	mdelay(20);
+}
+
+#endif /* !defined(CONFIG_SPL_BUILD) */
+
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ * Not called in SPL build.
+ */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+	hw_watchdog_init();
+#endif
+
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	/* Configure both I2C buses used in NRHW22 */
+	init_i2c();
+
+	da9063_init(CONFIG_PMIC_I2C_BUS);
+
+	/* Let user know we're starting */
+	set_status_led(1, 1);
+
+	printf("OSC:   %lu MHz\n", get_osclk()/1000000);
+
+	return 0;
+}
+
+#if !defined(CONFIG_SPL_BUILD)
+
+extern int console_init_f(void);
+extern void serial_set_console_index(int index);
+
+/*
+ * Set Linux console based on
+ * - Selection in /root/boot/consoledev
+ * - Available tty interfaces
+ *   - ttyS1: standard console (default)
+ *   - ttyS0: COM/IO shield (or used as console by kernel, 
+ *            when no other console available)
+ *   - ttyNull0: Dummy device if no real UART is available
+ */
+void set_console(void)
+{
+	const char *defaultconsole = getenv("defaultconsole");
+	char buf[20];
+	int i;
+
+	/* Set default console to ttyS1 if not yet defined in env */
+	if (defaultconsole == 0) {
+		setenv("defaultconsole", "ttyS1");
+	}
+
+	/* If consoledev file is present, take the tty defined in it as console */
+	if (read_file("/root/boot/consoledev",buf, sizeof(buf)) > 3) {
+		if (strstr(buf, "tty") == buf) {
+			buf[sizeof(buf)-1] = 0;
+			for (i=0; i<sizeof(buf); i++) {
+				if (buf[i]<=' ') {
+					buf[i] = 0;
+					break;
+				}
+			}
+			setenv("defaultconsole", buf);
+		}
+	}
+	
+#if defined(CONFIG_PRE_CONSOLE_BUFFER)
+	defaultconsole = getenv("defaultconsole");
+
+	serial_set_console_index(0);
+	serial_init(); /* serial communications setup */
+	console_init_f(); /* stage 1 init of console */
+#else
+    serial_set_console_index(1);
+#endif
+}
+
+static void set_devicetree_name(void)
+{
+	char devicetreename[64];
+
+	/* add hardware versions to environment */
+	if (bd_get_devicetree(devicetreename, sizeof(devicetreename)) != 0) {
+		printf("Devicetree name not found, using default name\n");
+		strcpy(devicetreename, "am335x-nrhw22-prod1.dtb");
+	}
+
+	setenv("fdt_image", devicetreename);
+}
+
+static void set_root_partition(void)
+{
+	int boot_partition;
+
+	/* add active root partition to environment */
+	boot_partition = bd_get_boot_partition();
+	if (boot_partition > 1) {
+		boot_partition = 0;
+	}
+
+	/* mmcblk1p1 => root0, mmcblk1p2 => root1 so +1 */
+	setenv_ulong("root_part", boot_partition + 1);
+}
+
+static void get_hw_version(void)
+{
+	int hw_ver, hw_rev;
+	char hw_versions[16];
+	char new_env[256];	/* current bootargs = 84 bytes */
+
+	bd_get_hw_version(&hw_ver, &hw_rev);
+	printf("HW22:  V%d.%d\n", hw_ver, hw_rev);
+
+	/* add hardware versions to environment */
+	snprintf(hw_versions, sizeof(hw_versions), "CP=%d.%d", hw_ver, hw_rev);
+	snprintf(new_env, sizeof(new_env), "setenv bootargs $bootargs %s", hw_versions);
+	setenv("add_version_bootargs", new_env);
+}
+
+static bool get_button_state(void)
+{
+	u8 state = 0x00;
+
+	(void)da9063_get_reg(PMIC_REG_STATUS_A, &state);
+
+	return (state & 0x01) == 0x01;
+}
+
+static void blink_led(int red)
+{
+	const int pulse_width = 400*1000; /* 400ms */
+
+	/* Assumes green status LED is on */
+	udelay(pulse_width);
+	set_status_led(red, 1-red);
+	udelay(pulse_width);
+	set_status_led(0, 1);
+}
+
+static void check_reset_button(void)
+{
+	int counter = 0;
+
+	/* Check how long button is pressed */
+	do {
+		if (!get_button_state())
+			break;
+
+		udelay(100*1000);  /* 100ms */
+		counter += 100;
+
+		if (counter == 2000) {
+			/* Indicate factory reset threshold */
+			blink_led(0);
+		}
+		else if (counter == 12000) {
+			/* Indicate recovery boot threshold */
+			blink_led(1);
+		}
+	} while (counter < 12000);
+
+	if (counter < 2000) {
+		/* Don't do anything for duration < 2s */
+	}
+	else if (counter < 12000)
+	{
+		/* Do factory reset for duration between 2s and 12s */
+		char new_bootargs[512];
+		char *bootargs = getenv("bootargs");
+
+		if (bootargs == 0) bootargs="";
+
+		printf("Do factory reset during boot...\n");
+
+		strncpy(new_bootargs, bootargs, sizeof(new_bootargs));
+		strncat(new_bootargs, " factory-reset", sizeof(new_bootargs));
+
+		setenv("bootargs", new_bootargs);
+	}
+	else
+	{
+		/* Boot into recovery for duration > 12s */
+
+		printf("Booting recovery image...\n");
+
+		/* Set consoledev to external port */
+		setenv("defaultconsole", "ttyS1");
+
+		/* Set bootcmd to run recovery */
+		setenv("bootcmd", "run recovery");
+	}
+}
+
+static void check_jtag_boot(void)
+{
+	if (is_jtag_boot(CONFIG_JTAG_MARKER_UBOOT)) {
+		char *bootcmd = getenv("bootcmd");
+		setenv ("bootcmd", "");
+		/* Save original bootcmd in "bc" to allow manual boot */
+		setenv ("bc", bootcmd);
+		puts("Detected JTAG boot. Waiting on command line\n");
+	}
+}
+
+#endif /* !defined(CONFIG_SPL_BUILD) */
+
+
+int board_late_init(void)
+{
+#if !defined(CONFIG_SPL_BUILD)
+	if (read_eeprom() < 0)
+		puts("Could not get board ID.\n");
+
+	get_hw_version();
+	set_root_partition();
+	set_devicetree_name();
+
+	/* Initialize pins */
+	REQUEST_AND_CLEAR_GPIO(NETBIRD_GPIO_RST_GNSS);
+
+	init_ethernet_switch();
+
+	check_reset_button();
+
+	set_console();
+
+	set_status_led(0, 0);
+
+	check_jtag_boot();
+#endif
+
+	return 0;
+}
+
+
+#ifndef CONFIG_DM_ETH
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_addr	= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_addr	= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+#endif
+
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) &&\
+	defined(CONFIG_SPL_BUILD)) || \
+	((defined(CONFIG_DRIVER_TI_CPSW) || \
+	  defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+	 !defined(CONFIG_SPL_BUILD))
+
+static void set_mac_address(int index, uchar mac[6])
+{
+	/* Then take mac from bd */
+	if (is_valid_ethaddr(mac)) {
+		eth_setenv_enetaddr_by_index("eth", index, mac);
+	}
+	else {
+		printf("Trying to set invalid MAC address");
+	}
+}
+
+/* TODO: Update doc */
+/*
+ * This function will:
+ * Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr
+ * in the environment
+ * Perform fixups to the PHY present on certain boards.  We only need this
+ * function in:
+ * - SPL with either CPSW or USB ethernet support
+ * - Full U-Boot, with either CPSW or USB ethernet
+ * Build in only these cases to avoid warnings about unused variables
+ * when we build an SPL that has neither option but full U-Boot will.
+ */
+int board_eth_init(bd_t *bis)
+{
+	int rv, n = 0;
+	uint8_t mac_addr0[6] = {02,00,00,00,00,01};
+	__maybe_unused struct ti_am_eeprom *header;
+
+#if !defined(CONFIG_SPL_BUILD)
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+	cpsw_data.mdio_div = 0x3E;
+
+	bd_get_mac(0, mac_addr0, sizeof(mac_addr0));
+	set_mac_address(0, mac_addr0);
+
+	writel(RMII_MODE_ENABLE | RMII_CHIPCKL_ENABLE, &cdev->miisel);
+	cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RMII;
+	cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RMII;
+	cpsw_slaves[0].phy_addr = 0;
+	cpsw_slaves[1].phy_addr = 1;
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		n += rv;
+#endif
+#endif
+
+#if defined(CONFIG_USB_ETHER) && \
+	(!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT))
+	if (is_valid_ethaddr(mac_addr0))
+		eth_setenv_enetaddr("usbnet_devaddr", mac_addr0);
+
+	rv = usb_eth_initialize(bis);
+	if (rv < 0)
+		printf("Error %d registering USB_ETHER\n", rv);
+	else
+		n += rv;
+#endif
+	return n;
+}
+#endif
+
+#endif /* CONFIG_DM_ETH */
+
+#ifdef CONFIG_SPL_LOAD_FIT
+int board_fit_config_name_match(const char *name)
+{
+	return 0;
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	return 0;
+}
+
+#endif

board/nm/nrhw22/board.h

@@ -0,0 +1,35 @@
+/*
+ * board.h
+ *
+ * TI AM335x boards information header
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+/*
+ * We have three pin mux functions that must exist.  We must be able to enable
+ * uart0, for initial output and i2c2 to read the main EEPROM.  We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void disable_uart0_pin_mux(void);
+void enable_uart1_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart5_pin_mux(void);
+/*
+void enable_uart2_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart4_pin_mux(void);
+void enable_uart5_pin_mux(void);
+*/
+void enable_i2c0_pin_mux(void);
+void enable_i2c2_pin_mux(void);
+void enable_board_pin_mux(void);
+
+#define GPIO_TO_PIN(bank, gpio)		(32 * (bank) + (gpio))
+#endif

board/nm/nrhw22/da9063.c

@@ -0,0 +1,92 @@
+/*
+ * da9063.c
+ *
+ * Dialog DA9063 PMIC
+ *
+ * Copyright (C) 2018 NetModule AG - http://www.netmodule.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <i2c.h>
+
+#include "da9063.h"
+
+
+static int da9063_i2c_bus = 0;
+
+
+void da9063_init(int i2c_bus)
+{
+	da9063_i2c_bus = i2c_bus;
+}
+
+int da9063_get_reg(int reg, u8* val)
+{
+	int ret;
+	int old_bus;
+	u8 temp;
+
+	/* TODO: Check whether switching is required */
+	old_bus = i2c_get_bus_num();
+	i2c_set_bus_num(da9063_i2c_bus);
+
+	/* TODO: Use CONFIG_PMIC_I2C_ADDR+1 if reg > 0xFF */
+	*val = 0;
+	ret = i2c_read(CONFIG_PMIC_I2C_ADDR, reg, 1, &temp, 1);
+	if (ret == 0)
+		*val = temp;
+
+	i2c_set_bus_num(old_bus);
+
+	return ret;
+}
+
+int da9063_set_reg(int reg, u8 val)
+{
+	int ret;
+	int old_bus;
+
+	/* TODO: Check whether switching is required */
+	old_bus = i2c_get_bus_num();
+	i2c_set_bus_num(da9063_i2c_bus);
+
+	/* TODO: Use CONFIG_PMIC_I2C_ADDR+1 if reg > 0xFF */
+	ret = i2c_write(CONFIG_PMIC_I2C_ADDR, reg, 1, &val, 1);
+	if (ret != 0)
+		puts("da9063 write error\n");
+
+	i2c_set_bus_num(old_bus);
+
+	return ret;
+}
+
+void da9063_set_gpio(unsigned bit, int state)
+{
+	int pmic_reg;
+	int ret;
+	u8 bitmask;
+	u8 reg = 0x00;
+
+	if (bit <= 7) {
+		pmic_reg = PMIC_REG_GPIO_MODE0_7;
+		bitmask = 1U << (bit-0);
+	}
+	else  {
+		pmic_reg = PMIC_REG_GPIO_MODE8_15;
+		bitmask = 1U << (bit-8);
+	}
+
+/*	printf("da9063_set_gpio %d 0x%04x\n", pmic_reg, bitmask); */
+	ret = da9063_get_reg(pmic_reg, &reg);
+
+	if (ret == 0)  {
+		if (state)	reg |=  bitmask;
+		else		reg &= ~bitmask;
+
+		(void)da9063_set_reg(pmic_reg, reg);
+	}
+}
+

board/nm/nrhw22/da9063.h

@@ -0,0 +1,36 @@
+/*
+ * da9063.c
+ *
+ * Dialog DA9063 PMIC
+ *
+ * Copyright (C) 2018 NetModule AG - http://www.netmodule.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef DA9063_H
+#define DA9063_H
+
+
+#define CONFIG_PMIC_I2C_BUS	0
+#define CONFIG_PMIC_I2C_ADDR	0x58	/* Pages 0 and 1, Pages 2 and 3 -> 0x59 */
+
+#define PMIC_REG_STATUS_A	0x01	/* Status of ON_KEY, WAKE, COMP1V2, DVC */
+#define PMIC_REG_GPIO_MODE0_7	0x1D	/* Control register for GPIOs 0..7 */
+#define PMIC_REG_GPIO_MODE8_15	0x1E	/* Control register for GPIOs 8..15 */
+
+#define PMIC_REG_BBAT_CONT	0xC5	/* Control register for backup battery */
+
+#define PMIC_REG_BUCK_ILIM_A	0x9A
+#define PMIC_REG_BUCK_ILIM_B	0x9B
+#define PMIC_REG_BUCK_ILIM_C	0x9C
+
+
+extern void da9063_init(int i2c_bus);
+extern int da9063_get_reg(int reg, u8* val);
+extern int da9063_set_reg(int reg, u8 val);
+
+extern void da9063_set_gpio(unsigned bit, int state);
+
+
+#endif /* DA9063_H */

board/nm/nrhw22/fileaccess.c

@@ -0,0 +1,40 @@
+#include <common.h>
+#include <fs.h>
+
+#define BLOCK_DEVICE "mmc"
+#define OVERLAY_PART "1:3"
+
+int read_file(const char* filename, char *buf, int size)
+{
+	loff_t filesize = 0;
+	loff_t len;
+	int ret;
+
+	if (fs_set_blk_dev(BLOCK_DEVICE, OVERLAY_PART, FS_TYPE_EXT) != 0) {
+		puts("Error, can not set blk device\n");
+		return -1;
+	}
+
+	/* Read at most file size bytes */
+	if (fs_size(filename, &filesize)) {
+		return -1;
+	}
+
+	if (filesize < size)
+		size = filesize;
+
+	/* For very unclear reasons the block device needs to be set again after the call to fs_size() */
+	if (fs_set_blk_dev(BLOCK_DEVICE, OVERLAY_PART, FS_TYPE_EXT) != 0) {
+		puts("Error, can not set blk device\n");
+		return -1;
+	}
+
+	if ((ret = fs_read(filename, (ulong)buf, 0, size, &len))) {
+		printf("Can't read file %s (size %d, len %lld, ret %d)\n", filename, size, len, ret);
+		return -1;
+	}
+
+	buf[len] = 0;
+
+	return len;
+}

board/nm/nrhw22/fileaccess.h

@@ -0,0 +1,14 @@
+/**@file	/home/eichenberger/projects/nbhw16/u-boot/board/nm/netbird_v2/fileaccess.h
+ * @author	eichenberger
+ * @version	704
+ * @date
+ * 	Created:	Tue 06 Jun 2017 02:02:33 PM CEST \n
+ * 	Last Update:	Tue 06 Jun 2017 02:02:33 PM CEST
+ */
+#ifndef FILEACCESS_H
+#define FILEACCESS_H
+
+void fs_set_console(void);
+int read_file(const char* filename, char *buf, int size);
+
+#endif // FILEACCESS_H

board/nm/nrhw22/mux.c

@@ -0,0 +1,146 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2018 NetModule AG - http://www.netmodule.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include "board.h"
+
+static struct module_pin_mux gpio_pin_mux[] = {
+	/*
+	* GPIO0_2: RST_GNSS~
+	* GPIO0_5: EXTINT_GNSS
+	* GPIO0_6: TIMEPULSE_GNSS
+	* GPIO0_16: RST_PHY~
+	* GPIO0_17: PMIC FAULT
+	*
+	*/
+
+	/* Bank 0 */
+	{OFFSET(spi0_sclk), (MODE(7) | PULLUDDIS)},			/* (A17) gpio0[2] */  /* RST_GNSS */
+	{OFFSET(spi0_cs0), (MODE(7) | PULLUDEN | PULLDOWN_EN)},		/* (A16) gpio0[5] */  /* EXTINT_GNSS */
+	{OFFSET(spi0_cs1), (MODE(7) | PULLUDEN | PULLUP_EN | RXACTIVE)},/* (C15) gpio0[6] */  /* TIMEPULSE_GNSS */
+	{OFFSET(mii1_txd3), (MODE(7) | PULLUDDIS)},			/* (J18) gpio0[16] */  /* RST_PHY~ */
+	{OFFSET(mii1_txd2), (MODE(7) | PULLUDDIS | RXACTIVE)},		/* (K15) gpio0[17] */  /* PMIC_FAULT */
+
+	{-1},
+};
+
+/* I2C0 PMIC */
+static struct module_pin_mux i2c0_pin_mux[] = {
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN | SLEWCTRL)},	/* (C17) I2C0_SDA */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE | PULLUDEN | PULLUP_EN | SLEWCTRL)},	/* (C16) I2C0_SCL */
+	{-1},
+};
+
+/* I2C2 System */
+static struct module_pin_mux i2c2_pin_mux[] = {
+	{OFFSET(uart1_rtsn), (MODE(3) | RXACTIVE | PULLUDEN | PULLUP_EN | SLEWCTRL)},	/* (D17) I2C2_SCL */
+	{OFFSET(uart1_ctsn), (MODE(3) | RXACTIVE | PULLUDEN | PULLUP_EN | SLEWCTRL)},	/* (D18) I2C2_SDA */
+	{-1},
+};
+
+/* RMII1: Ethernet Switch */
+static struct module_pin_mux rmii1_pin_mux[] = {
+	/* RMII */
+	{OFFSET(mii1_crs), MODE(1) | PULLUDDIS | RXACTIVE},			/* (H17) rmii1_crs */
+	{OFFSET(mii1_rxerr), MODE(7) | PULLUDEN | PULLDOWN_EN | RXACTIVE},	/* (J15) gpio */
+	{OFFSET(mii1_rxd0), MODE(1) | PULLUDDIS | RXACTIVE},			/* (M16) rmii1_rxd0 */
+	{OFFSET(mii1_rxd1), MODE(1) | PULLUDDIS | RXACTIVE},			/* (L15) rmii1_rxd1 */
+	{OFFSET(mii1_txen), MODE(1) | PULLUDDIS},				/* (J16) rmii1_txen */
+	{OFFSET(mii1_txd0), MODE(1) | PULLUDDIS},				/* (K17) rmii1_txd0 */
+	{OFFSET(mii1_txd1), MODE(1) | PULLUDDIS},				/* (K16) rmii1_txd1 */
+	{OFFSET(rmii1_refclk), MODE(0) | PULLUDDIS | RXACTIVE},			/* (H18) rmii1_refclk */
+
+	/* SMI */
+	{OFFSET(mdio_clk), MODE(0) | PULLUDDIS},				/* (M18) mdio_clk */
+	{OFFSET(mdio_data), MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE},		/* (M17) mdio_data */
+
+	/* 25MHz Clock Output */
+	{OFFSET(xdma_event_intr0), MODE(3)},					/* (A15) clkout1 (25 MHz clk for Switch) */
+	{-1},
+};
+
+/* MMC1: eMMC */
+static struct module_pin_mux mmc1_emmc_pin_mux[] = {
+	{OFFSET(gpmc_csn1), (MODE(2) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_CMD */
+	{OFFSET(gpmc_ad0), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_ad1), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad2), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad3), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad4), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT4 */
+	{OFFSET(gpmc_ad5), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT5 */
+	{OFFSET(gpmc_ad6), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT6 */
+	{OFFSET(gpmc_ad7), (MODE(1) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* MMC1_DAT7 */
+	{-1},
+};
+
+/* UART0: RS232 console */
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* (E15) UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN | PULLUP_EN | SLEWCTRL)},	/* (E16) UART0_TXD */
+	{-1},
+};
+
+/* UART1: GNSS */
+static struct module_pin_mux uart1_pin_mux[] = {
+	{OFFSET(uart1_rxd), (MODE(0) | PULLUDEN | PULLUP_EN | RXACTIVE)},	/* (D16) uart1_rxd */
+	{OFFSET(uart1_txd), (MODE(0) | PULLUDEN | PULLUP_EN | SLEWCTRL)},	/* (D15) uart1_txd */
+	{-1},
+};
+
+static struct module_pin_mux unused_pin_mux[] = {
+	/* SYSBOOT6, 7, 10, 11: Not used pulldown active, receiver disabled */
+	{OFFSET(lcd_data6), (MODE(7) | PULLUDEN | PULLDOWN_EN)},
+	{OFFSET(lcd_data7), (MODE(7) | PULLUDEN | PULLDOWN_EN)},
+	{OFFSET(lcd_data10), (MODE(7) | PULLUDEN | PULLDOWN_EN)},
+	{OFFSET(lcd_data11), (MODE(7) | PULLUDEN | PULLDOWN_EN)},
+
+	/* TODO: GPMCA1..3, A6..8 */
+
+	{-1},
+};
+
+
+void enable_board_pin_mux(void)
+{
+	configure_module_pin_mux(gpio_pin_mux);
+
+	configure_module_pin_mux(rmii1_pin_mux);
+	configure_module_pin_mux(mmc1_emmc_pin_mux);
+
+	configure_module_pin_mux(i2c0_pin_mux);
+	configure_module_pin_mux(i2c2_pin_mux);
+
+	configure_module_pin_mux(uart0_pin_mux);
+	configure_module_pin_mux(uart1_pin_mux);
+
+	configure_module_pin_mux(unused_pin_mux);
+}
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_uart1_pin_mux(void)
+{
+	configure_module_pin_mux(uart1_pin_mux);
+}
+

board/nm/nrhw22/u-boot.lds

@@ -0,0 +1,158 @@
+/*
+ * Copyright (c) 2004-2008 Texas Instruments
+ *
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text :
+	{
+		*(.__image_copy_start)
+		*(.vectors)
+		CPUDIR/start.o (.text*)
+                board/nm/nrhw22/built-in.o (.text*)
+		*(.text*)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) }
+
+	. = ALIGN(4);
+	.data : {
+		*(.data*)
+	}
+
+	. = ALIGN(4);
+
+	. = .;
+
+	. = ALIGN(4);
+	.u_boot_list : {
+		KEEP(*(SORT(.u_boot_list*)));
+	}
+
+	. = ALIGN(4);
+
+	.__efi_runtime_start : {
+		*(.__efi_runtime_start)
+	}
+
+	.efi_runtime : {
+		*(efi_runtime_text)
+		*(efi_runtime_data)
+	}
+
+	.__efi_runtime_stop : {
+		*(.__efi_runtime_stop)
+	}
+
+	.efi_runtime_rel_start :
+	{
+		*(.__efi_runtime_rel_start)
+	}
+
+	.efi_runtime_rel : {
+		*(.relefi_runtime_text)
+		*(.relefi_runtime_data)
+	}
+
+	.efi_runtime_rel_stop :
+	{
+		*(.__efi_runtime_rel_stop)
+	}
+
+	. = ALIGN(4);
+
+	.image_copy_end :
+	{
+		*(.__image_copy_end)
+	}
+
+	.rel_dyn_start :
+	{
+		*(.__rel_dyn_start)
+	}
+
+	.rel.dyn : {
+		*(.rel*)
+	}
+
+	.rel_dyn_end :
+	{
+		*(.__rel_dyn_end)
+	}
+
+	.hash : { *(.hash*) }
+
+	.end :
+	{
+		*(.__end)
+	}
+
+	_image_binary_end = .;
+
+	/*
+	 * Deprecated: this MMU section is used by pxa at present but
+	 * should not be used by new boards/CPUs.
+	 */
+	. = ALIGN(4096);
+	.mmutable : {
+		*(.mmutable)
+	}
+
+/*
+ * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
+ * __bss_base and __bss_limit are for linker only (overlay ordering)
+ */
+
+	.bss_start __rel_dyn_start (OVERLAY) : {
+		KEEP(*(.__bss_start));
+		__bss_base = .;
+	}
+
+	.bss __bss_base (OVERLAY) : {
+		*(.bss*)
+		 . = ALIGN(4);
+		 __bss_limit = .;
+	}
+
+	.bss_end __bss_limit (OVERLAY) : {
+		KEEP(*(.__bss_end));
+	}
+
+	.dynsym _image_binary_end : { *(.dynsym) }
+	.dynbss : { *(.dynbss) }
+	.dynstr : { *(.dynstr*) }
+	.dynamic : { *(.dynamic*) }
+	.gnu.hash : { *(.gnu.hash) }
+	.plt : { *(.plt*) }
+	.interp : { *(.interp*) }
+	.gnu : { *(.gnu*) }
+	.ARM.exidx : { *(.ARM.exidx*) }
+}

common/board_f.c

@@ -888,8 +888,10 @@ static init_fnc_t init_sequence_f[] = {
 	init_timebase,
 #endif
 	init_baud_rate,		/* initialze baudrate settings */
+#if !defined(CONFIG_PRE_CONSOLE_BUFFER)
 	serial_init,		/* serial communications setup */
 	console_init_f,		/* stage 1 init of console */
+#endif
 #ifdef CONFIG_SANDBOX
 	sandbox_early_getopt_check,
 #endif

common/console.c

@@ -414,7 +414,7 @@ int tstc(void)
 #define PRE_CONSOLE_FLUSHPOINT2_EVERYTHING_BUT_SERIAL	1
 
 #ifdef CONFIG_PRE_CONSOLE_BUFFER
-#define CIRC_BUF_IDX(idx) ((idx) % (unsigned long)CONFIG_PRE_CON_BUF_SZ)
+#define CIRC_BUF_IDX(idx) ((idx) % (unsigned long)(CONFIG_PRE_CON_BUF_SZ))
 
 static void pre_console_putc(const char c)
 {

common/main.c

@@ -13,6 +13,11 @@
 #include <console.h>
 #include <version.h>
 
+#include <fs.h>
+#include <u-boot/md5.h>
+#include <malloc.h>
+#include <crypt.h>
+
 DECLARE_GLOBAL_DATA_PTR;
 
 /*
@@ -20,6 +25,93 @@ DECLARE_GLOBAL_DATA_PTR;
  */
 __weak void show_boot_progress(int val) {}
 
+
+#ifdef CONFIG_NM_LOGIN
+/****************************************************************************
+ *  check if ubootpwd exists in data partition and perform a login,
+ *  otherwise continue booting
+ */
+int login (void)
+{
+	#define PASS_LEN 256
+	char stored[PASS_LEN];
+	char buf[PASS_LEN], entered[32];
+	int res, i, tries;
+	int legacy_md5 = 0;
+	loff_t actread;
+
+	puts("\nautoboot has been stopped, press 'e' to enter: ");
+
+	for (i=0; i<=4096; i++) {
+		buf[0] = getc();
+		if (buf[0] == 'e' || buf[0] == '\n') {
+			puts("e");
+			break;
+		}
+		if (i == 4096) return 0;
+	}
+	puts("\n");
+
+	memset(stored, 0x0, sizeof(stored));
+
+	if (fs_set_blk_dev("mmc", "1:3", FS_TYPE_EXT) != 0) {
+		puts("Error, can not set blk devicet");
+		return 1;
+	}
+
+	res = fs_read("/root/boot/bootpass", (ulong)stored, 0, sizeof(stored), &actread);
+	if ((res!=0) || (actread <= 0)) {
+		/* no file or hash found */
+		puts("Login succeeded\n\n");
+		return 1;
+	} else if (actread == 16) {
+		legacy_md5 = 1;
+	}
+
+	for (tries = 1; ; tries++) {
+		puts("\nEnter password: ");
+
+		buf[0] = 0;
+		for (i=0; i<PASS_LEN; i++) {
+			buf[i] = getc();
+			if (buf[i] == '\r' || buf[i] == '\n') {
+				buf[i] = 0;
+				break;
+			}
+		}
+		buf[PASS_LEN-1] = 0;
+
+		if (strlen(buf) > 0) {
+			puts("\n");
+			if (legacy_md5) {
+				md5((unsigned char*) buf, strlen(buf), (unsigned char *)entered);
+				if (memcmp(stored, entered, 16) == 0) {
+					break;
+				}
+			}	else {
+				char *cp = sha_crypt(buf, stored);
+				if (memcmp(cp, stored, actread) == 0) {
+					free(cp);
+					break;
+				}
+				free(cp);
+			}
+			puts("Login incorrect\n");
+			if (tries == 3) {
+				return 0;
+			}
+		}
+	}
+
+	/* succeeded */
+	puts("Login succeeded\n\n");
+	return 1;
+}
+
+#endif /* CONIFG_NM_LOGIN */
+
+/****************************************************************************/
+
 static void run_preboot_environment_command(void)
 {
 #ifdef CONFIG_PREBOOT
@@ -65,6 +157,13 @@ void main_loop(void)
 
 	autoboot_command(s);
 
+#ifdef CONFIG_NM_LOGIN
+	if (!login()) {
+		puts ("Login failed, resetting...\n");
+		do_reset (NULL, 0, 0, NULL);
+	}
+#endif
+
 	cli_loop();
 	panic("No CLI available");
 }

common/spl/spl.c

@@ -18,6 +18,7 @@
 #include <malloc.h>
 #include <dm/root.h>
 #include <linux/compiler.h>
+#include <spl_version_autogenerated.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -453,7 +454,8 @@ void preloader_console_init(void)
 
 	gd->have_console = 1;
 
-	puts("\nU-Boot SPL " PLAIN_VERSION " (" U_BOOT_DATE " - " \
+	puts("\n" SPL_VERSION "\n");
+	puts("U-Boot SPL " PLAIN_VERSION " (" U_BOOT_DATE " - " \
 			U_BOOT_TIME ")\n");
 #ifdef CONFIG_SPL_DISPLAY_PRINT
 	spl_display_print();

common/spl/spl_mmc.c

@@ -24,11 +24,18 @@ static int mmc_load_legacy(struct mmc *mmc, ulong sector,
 	u32 image_size_sectors;
 	unsigned long count;
 	int ret;
+	int nm_additional_header_bytes;
+	int nm_additional_trailer_bytes;
 
 	ret = spl_parse_image_header(header);
 	if (ret)
 		return ret;
 
+	nm_additional_header_bytes = sizeof(struct nm_header) - sizeof(struct image_header);
+	nm_additional_trailer_bytes = sizeof(__be32);
+	spl_image.load_addr -= nm_additional_header_bytes;
+	spl_image.size += nm_additional_header_bytes + nm_additional_trailer_bytes;
+
 	/* convert size to sectors - round up */
 	image_size_sectors = (spl_image.size + mmc->read_bl_len - 1) /
 			     mmc->read_bl_len;
@@ -54,21 +61,32 @@ static ulong h_spl_load_read(struct spl_load_info *load, ulong sector,
 
 static int mmc_load_image_raw_sector(struct mmc *mmc, unsigned long sector)
 {
+	const unsigned int START_MAGIC = 0x424c5354;
+	const unsigned int END_MAGIC   = 0x424c454e;
+
 	unsigned long count;
+	struct nm_header *nm_header;
 	struct image_header *header;
 	int ret = 0;
+	__be32* end_tag_position;
 
-	header = (struct image_header *)(CONFIG_SYS_TEXT_BASE -
+	nm_header = (struct nm_header *)(CONFIG_SYS_TEXT_BASE -
-					 sizeof(struct image_header));
+					 sizeof(struct nm_header));
 
 	/* read image header to find the image size & load address */
-	count = blk_dread(mmc_get_blk_desc(mmc), sector, 1, header);
+	count = blk_dread(mmc_get_blk_desc(mmc), sector, 1, nm_header);
 	debug("hdr read sector %lx, count=%lu\n", sector, count);
 	if (count == 0) {
 		ret = -EIO;
 		goto end;
 	}
 
+	if (be32_to_cpu(nm_header->nm_start_tag) != START_MAGIC) return -1;
+	if (be32_to_cpu(nm_header->nm_length)>10000000) return -1;
+	end_tag_position = (__be32*)(((void*)nm_header) + sizeof(struct nm_header) - sizeof(struct image_header) + (be32_to_cpu(nm_header->nm_length)));
+
+	header = &(nm_header->header);
+
 	if (IS_ENABLED(CONFIG_SPL_LOAD_FIT) &&
 	    image_get_magic(header) == FDT_MAGIC) {
 		struct spl_load_info load;
@@ -84,6 +102,8 @@ static int mmc_load_image_raw_sector(struct mmc *mmc, unsigned long sector)
 		ret = mmc_load_legacy(mmc, sector, header);
 	}
 
+	if (be32_to_cpu(*end_tag_position) != END_MAGIC) return -1;
+
 end:
 	if (ret) {
 #ifdef CONFIG_SPL_LIBCOMMON_SUPPORT
@@ -92,6 +112,8 @@ end:
 		return -1;
 	}
 
+	printf("Found valid u-boot image at sector %ld\n", sector);
+
 	return 0;
 }
 
@@ -324,6 +346,9 @@ int spl_mmc_load_image(u32 boot_device)
 #if defined(CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR)
 		err = mmc_load_image_raw_sector(mmc,
 			CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR);
+		if (err)
+			err = mmc_load_image_raw_sector(mmc,
+				CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR_ALTERNATE);
 		if (!err)
 			return err;
 #endif

configs/am335x_nrhw22_defconfig

@@ -0,0 +1,49 @@
+CONFIG_ARM=y
+CONFIG_TARGET_AM335X_NRHW22=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SPL=y
+CONFIG_SPL_STACK_R=y
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT"
+CONFIG_HUSH_PARSER=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Press s to abort autoboot in %d seconds\n"
+CONFIG_AUTOBOOT_STOP_STR="s"
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_ASKENV=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_I2C=y
+# CONFIG_CMD_USB is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_DFU_TFTP=y
+CONFIG_SYS_NS16550=y
+# CONFIG_USB is not set
+# CONFIG_USB_MUSB_HOST is not set
+# CONFIG_USB_MUSB_GADGET is not set
+# CONFIG_USB_GADGET is not set
+# CONFIG_USB_GADGET_DOWNLOAD is not set
+CONFIG_G_DNL_MANUFACTURER="Texas Instruments"
+CONFIG_G_DNL_VENDOR_NUM=0x0451
+CONFIG_G_DNL_PRODUCT_NUM=0xd022
+CONFIG_OF_LIBFDT=y
+# CONFIG_BOOTP_PXE_CLIENTARCH is not set
+# CONFIG_CMD_PXE is not set
+# CONFIG_CMD_BOOTEFI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_FPGA is not set
+# CONFIG_CMD_FPGA is not set
+# CONFIG_CMD_PMIC is not set
+# CONFIG_EFI_LOADER is not set
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set

drivers/serial/serial-uclass.c

@@ -27,6 +27,17 @@ static const unsigned long baudrate_table[] = CONFIG_SYS_BAUDRATE_TABLE;
 #error "Serial is required before relocation - define CONFIG_SYS_MALLOC_F_LEN to make this work"
 #endif
 
+#ifdef CONFIG_CONS_INDEX
+static int CONSOLE_INDEX = CONFIG_CONS_INDEX - 1;
+#else
+static int CONSOLE_INDEX = 0;
+#endif
+
+void serial_set_console_index(int index)
+{
+	CONSOLE_INDEX = index;
+}
+
 static void serial_find_console_or_panic(void)
 {
 	const void *blob = gd->fdt_blob;
@@ -84,18 +95,12 @@ static void serial_find_console_or_panic(void)
 		 * extremis just the first serial device we can find. But we
 		 * insist on having a console (even if it is silent).
 		 */
-#ifdef CONFIG_CONS_INDEX
+		if (!uclass_get_device_by_seq(UCLASS_SERIAL, CONSOLE_INDEX, &dev) ||
-#define INDEX (CONFIG_CONS_INDEX - 1)
+		    !uclass_get_device(UCLASS_SERIAL, CONSOLE_INDEX, &dev) ||
-#else
-#define INDEX 0
-#endif
-		if (!uclass_get_device_by_seq(UCLASS_SERIAL, INDEX, &dev) ||
-		    !uclass_get_device(UCLASS_SERIAL, INDEX, &dev) ||
 		    (!uclass_first_device(UCLASS_SERIAL, &dev) && dev)) {
 			gd->cur_serial_dev = dev;
 			return;
 		}
-#undef INDEX
 	}
 
 #ifdef CONFIG_REQUIRE_SERIAL_CONSOLE
@@ -115,7 +120,9 @@ int serial_init(void)
 /* Called after relocation */
 void serial_initialize(void)
 {
+#if !defined(CONFIG_PRE_CONSOLE_BUFFER)
 	serial_init();
+#endif
 }
 
 static void _serial_putc(struct udevice *dev, char ch)

fs/fs.c

@@ -307,8 +307,6 @@ int fs_read(const char *filename, ulong addr, loff_t offset, loff_t len,
 	unmap_sysmem(buf);
 
 	/* If we requested a specific number of bytes, check we got it */
-	if (ret == 0 && len && *actread != len)
-		printf("** %s shorter than offset + len **\n", filename);
 	fs_close();
 
 	return ret;

include/configs/am335x_netbird.h

@@ -49,7 +49,7 @@
 	"kernel_addr=0x80000000\0" \
 	"load_addr=0x83000000\0" \
 	"root_part=1\0" /* Default root partition, overwritte in board/mv_ebu/a38x/nbhw14_env.c */ \
-	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/mmcblk0p$root_part rootfstype=ext4 console=ttyO0,115200 rootwait earlyprintk\0" \
+	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/mmcblk1p$root_part rootfstype=ext4 console=ttyO0,115200 rootwait earlyprintk\0" \
 	"add_version_bootargs=setenv bootargs $bootargs\0" \
 	"fdt_skip_update=yes\0" \
     "ethprime=cpsw\0" \

include/configs/am335x_netbird_v2.h

@@ -59,7 +59,7 @@
 	"load_addr=" LOAD_ADDR "\0" \
 	"root_part=1\0" /* Default root partition, overwritte in board file */ \
 	"defaultconsole=ttyS1\0" /* Default output console */ \
-	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/mmcblk0p$root_part rootfstype=ext4 console=$defaultconsole,115200 rootwait loglevel=4\0" \
+	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/mmcblk1p$root_part rootfstype=ext4 console=$defaultconsole,115200 rootwait loglevel=4\0" \
 	"add_version_bootargs=setenv bootargs $bootargs\0" \
 	"fdt_skip_update=yes\0" \
 	"ethprime=cpsw\0" \

include/configs/am335x_nrhw20.h

@@ -36,6 +36,10 @@
 #define CONFIG_MACH_TYPE		MACH_TYPE_TIAM335EVM
 #define CONFIG_BOARD_LATE_INIT
 
+#define CONFIG_PRE_CONSOLE_BUFFER 1
+#define CONFIG_PRE_CON_BUF_ADDR   0x80000000
+#define CONFIG_PRE_CON_BUF_SZ     64*1024
+
 /* Clock Defines */
 #define V_OSCK				0 /* 0 means detect from sysboot1 config */
 #define V_SCLK				(V_OSCK)
@@ -52,7 +56,7 @@
 #define LOAD_ADDR			"0x83000000"
 #define FDT_ADDR			"0x82000000"
 #define PXE_ADDR			"0x82800000"
-#define FDT_HIGH_ADDR			"0x87000000"
+#define FDT_HIGH_ADDR			"0x9f000000"
 #define INIT_RD_ADDR			"0x88000000"
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
@@ -64,7 +68,7 @@
 	"load_addr=" LOAD_ADDR "\0" \
 	"root_part=1\0" /* Default root partition, overwritten in board file */ \
 	"defaultconsole=ttyS1\0" /* Default output console */ \
-	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/mmcblk1p$root_part rootfstype=ext4 " \
+	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/${mmc_dev}p$root_part rootfstype=ext4 " \
 			"console=$defaultconsole,115200 rootwait loglevel=4 ti_cpsw.rx_packet_max=1526\0" \
 	"add_version_bootargs=setenv bootargs $bootargs\0" \
 	"fdt_skip_update=yes\0" \
@@ -76,7 +80,9 @@
 	"sdboot=if mmc dev 1; then echo Copying Linux from SD to RAM...; "\
 			"if test -e mmc 1:$root_part /boot/$kernel_image; then run sdprod; " \
 			"else run sdbringup; fi; " \
-			"run add_sd_bootargs; run add_version_bootargs; run shieldcmd; run modifyfdtcmd; " \
+			/* For v4.19 kernel $mmc_dev should be "mmcblk1" (read from DT), for v3.18 kernel: "mmcblk0". */ \
+			"fdt addr $fdt_addr;if fdt get value mmc_dev /nm_env nm,mmc-dev;then;else setenv mmc_dev mmcblk0;fi;" \
+			"run add_sd_bootargs; run add_version_bootargs; run shieldcmd; " \
 			"bootz $kernel_addr - $fdt_addr; fi\0" \
 	"bootcmd=run sdboot\0" \
 	"ipaddr=192.168.1.1\0" \
@@ -93,11 +99,9 @@
 	"bootpretryperiod=2000\0" \
 	"autoload=false\0" \
 	"shieldcmd=\0" \
-	"fdtshieldcmd=\0" \
-	"modifyfdtcmd=fdt addr $fdt_addr; run fdtshieldcmd;\0" \
 	"tftp_recovery=tftpboot $kernel_addr recovery-image; tftpboot $fdt_addr recovery-dtb; " \
 			"setenv bootargs rdinit=/etc/preinit console=$defaultconsole,115200 " \
-			"debug ti_cpsw.rx_packet_max=1526; run shieldcmd; run modifyfdtcmd; " \
+			"debug ti_cpsw.rx_packet_max=1526; run shieldcmd; " \
 			"bootz $kernel_addr - $fdt_addr\0" \
 	"pxe_recovery=sleep 3 && dhcp && pxe get && pxe boot\0" \
 	"recovery=run pxe_recovery || setenv ipaddr $ipaddr; setenv serverip $serverip; run tftp_recovery\0" \
@@ -107,6 +111,10 @@
 /* UART Configuration */
 #define CONFIG_SYS_NS16550_COM1			0x44e09000	/* UART0: XModem Boot, Shield */
 #define CONFIG_SYS_NS16550_COM2			0x48022000	/* UART1: eMMC Boot, User UART */
+#define CONFIG_SYS_NS16550_COM3			0x48024000	/* Unused */
+#define CONFIG_SYS_NS16550_COM4			0x481A6000	/* GNSS */
+#define CONFIG_SYS_NS16550_COM5			0x481A8000	/* Unused */
+#define CONFIG_SYS_NS16550_COM6			0x481AA000	/* Bluetooth */
 
 #define CONFIG_I2C
 #define CONFIG_I2C_MULTI_BUS
@@ -224,6 +232,9 @@
 #define CONFIG_SYS_MEMTEST_START    0x80000000
 #define CONFIG_SYS_MEMTEST_END      0x87900000
 
+#define CONFIG_NM_LOGIN
+#define CONFIG_CRYPT
+
 #if 0
 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
@@ -232,13 +243,15 @@
 
 #define CONFIG_CMD_PXE
 
+#define CONFIG_OF_BOARD_SETUP
+
+#define CONFIG_JTAG_MARKER_SPL		0x402FFF00
+#define CONFIG_JTAG_MARKER_UBOOT	0x807FFF00
+
 /* SPL command is not needed */
 #undef CONFIG_CMD_SPL
 
 /* Never enable ISO it is broken and can lead to a crash */
 #undef CONFIG_ISO_PARTITION
 
-
-
-
 #endif	/* ! __CONFIG_AM335X_NRHW20_H */

include/configs/am335x_nrhw22.h

@@ -0,0 +1,228 @@
+/*
+ * am335x_nrhw22.h
+ *
+ * Copyright (C) 2018 NetModule AG - http://www.netmodule.com/
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __CONFIG_AM335X_NRHW22_H
+#define __CONFIG_AM335X_NRHW22_H
+
+#include <configs/ti_am335x_common.h>
+
+#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
+
+#undef CONFIG_HW_WATCHDOG
+#undef CONFIG_OMPAP_WATCHDOG
+#undef CONFIG_SPL_WATCHDOG_SUPPORT
+
+#ifndef CONFIG_SPL_BUILD
+# define CONFIG_TIMESTAMP
+# define CONFIG_LZO
+#endif
+
+#define CONFIG_SYS_BOOTM_LEN		(16 << 20)
+
+#define MACH_TYPE_TIAM335EVM		3589	/* Until the next sync */
+#define CONFIG_MACH_TYPE		MACH_TYPE_TIAM335EVM
+#define CONFIG_BOARD_LATE_INIT
+
+#if 0
+#define CONFIG_PRE_CONSOLE_BUFFER 1
+#define CONFIG_PRE_CON_BUF_ADDR   0x80000000
+#define CONFIG_PRE_CON_BUF_SZ     64*1024
+#endif
+
+/* Clock Defines */
+#define V_OSCK				0 /* 0 means detect from sysboot1 config */
+#define V_SCLK				(V_OSCK)
+
+#include <config_distro_bootcmd.h>
+
+#define CONFIG_ARP_TIMEOUT		200
+#undef CONFIG_NET_RETRY_COUNT
+#define CONFIG_NET_RETRY_COUNT		5
+#define CONFIG_BOOTP_MAY_FAIL
+
+#ifndef CONFIG_SPL_BUILD
+#define KERNEL_ADDR			"0x80000000"
+#define LOAD_ADDR			"0x83000000"
+#define FDT_ADDR			"0x82000000"
+#define PXE_ADDR			"0x82800000"
+#define FDT_HIGH_ADDR			"0x9f000000"
+#define INIT_RD_ADDR			"0x88000000"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"kernel_image=kernel.bin\0"	\
+	"fdt_image=openwrt-nrhw22-nb650.dtb\0"\
+	"modeboot=sdboot\0" \
+	"fdt_addr=" FDT_ADDR "\0" \
+	"kernel_addr=" KERNEL_ADDR "\0" \
+	"load_addr=" LOAD_ADDR "\0" \
+	"root_part=1\0" /* Default root partition, overwritten in board file */ \
+	"defaultconsole=ttyS1\0" /* Default output console */ \
+	"add_sd_bootargs=setenv bootargs $bootargs root=/dev/mmcblk1p$root_part rootfstype=ext4 " \
+			"console=$defaultconsole,115200 rootwait loglevel=4 ti_cpsw.rx_packet_max=1526\0" \
+	"add_version_bootargs=setenv bootargs $bootargs\0" \
+	"fdt_skip_update=yes\0" \
+	"ethprime=cpsw\0" \
+	"sdbringup=echo Try bringup boot && ext4load mmc 1:$root_part $kernel_addr /boot/zImage && " \
+			"ext4load mmc 1:$root_part $fdt_addr /boot/$fdt_image && setenv bootargs $bootargs rw;\0" \
+	"sdprod=ext4load mmc 1:$root_part $kernel_addr /boot/$kernel_image && " \
+			"ext4load mmc 1:$root_part $fdt_addr /boot/$fdt_image && setenv bootargs $bootargs ro;\0" \
+	"sdboot=if mmc dev 1; then echo Copying Linux from SD to RAM...; "\
+			"if test -e mmc 1:$root_part /boot/$kernel_image; then run sdprod; " \
+			"else run sdbringup; fi; " \
+			"run add_sd_bootargs; run add_version_bootargs; run shieldcmd; " \
+			"bootz $kernel_addr - $fdt_addr; fi\0" \
+	"bootcmd=run sdboot\0" \
+	"ipaddr=192.168.1.1\0" \
+	"serverip=192.168.1.254\0" \
+	"pxefile_addr_r=" PXE_ADDR "\0" \
+	"fdt_addr_r=" FDT_ADDR "\0" \
+	"fdt_high=" FDT_HIGH_ADDR "\0" \
+	"kernel_addr_r=" KERNEL_ADDR "\0" \
+	"ramdisk_addr_r=" LOAD_ADDR "\0" \
+	"initrd_high=" INIT_RD_ADDR "\0" \
+	"bootpretryperiod=1000\0" \
+	"tftptimeout=2000\0" \
+	"tftptimeoutcountmax=5\0" \
+	"bootpretryperiod=2000\0" \
+	"autoload=false\0" \
+	"shieldcmd=\0" \
+	"tftp_recovery=tftpboot $kernel_addr recovery-image; tftpboot $fdt_addr recovery-dtb; " \
+			"setenv bootargs rdinit=/etc/preinit console=$defaultconsole,115200 " \
+			"debug ti_cpsw.rx_packet_max=1526; run shieldcmd; " \
+			"bootz $kernel_addr - $fdt_addr\0" \
+	"pxe_recovery=sleep 3 && dhcp && pxe get && pxe boot\0" \
+	"recovery=run pxe_recovery || setenv ipaddr $ipaddr; setenv serverip $serverip; run tftp_recovery\0" \
+			/* setenv ipaddr and serverip is necessary, because dhclient can destroy the IPs inernally */
+#endif
+
+/* UART Configuration */
+#define CONFIG_SYS_NS16550_COM1			0x44e09000	/* UART0: Console */
+#define CONFIG_SYS_NS16550_COM2			0x48022000	/* UART1: GNSS */
+#define CONFIG_SYS_NS16550_COM3			0x48024000	/* Unused */
+#define CONFIG_SYS_NS16550_COM4			0x481A6000	/* Unused */
+#define CONFIG_SYS_NS16550_COM5			0x481A8000	/* Unused */
+#define CONFIG_SYS_NS16550_COM6			0x481AA000	/* Unused */
+
+#define CONFIG_I2C
+#define CONFIG_I2C_MULTI_BUS
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR              0x50	/* Main EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
+#define CONFIG_SYS_I2C_SPEED                    100000
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   50	/* TODO: Can this be reduced to 20ms */
+
+/* Put Environment in eMMC */
+#define CONFIG_ENV_OFFSET			(512 * 128)	/* @ 512*256 SPL starts */
+#define CONFIG_ENV_SIZE				(4 * 1024)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV			1
+
+#if 0
+#define CONFIG_SYS_MMC_ENV_PART			2
+#define CONFIG_ENV_OFFSET_REDUND		(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#endif
+
+
+#undef CONFIG_SPL_ENV_SUPPORT
+#undef CONFIG_SPL_NAND_SUPPORT
+#undef CONFIG_SPL_ONENAND_SUPPORT
+
+/* We need to disable SPI to not confuse the eeprom env driver */
+#undef CONFIG_SPI
+#undef CONFIG_SPI_BOOT
+#undef CONFIG_SPL_OS_BOOT
+
+#define CONFIG_SPL_POWER_SUPPORT	/* TODO: Check */
+#define CONFIG_SPL_YMODEM_SUPPORT
+
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/am33xx/u-boot-spl.lds"
+
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* To support eMMC booting */
+#define CONFIG_STORAGE_EMMC
+#define CONFIG_FASTBOOT_FLASH_MMC_DEV   1
+
+#ifdef CONFIG_USB_MUSB_HOST
+#define CONFIG_USB_STORAGE
+#endif
+
+#ifdef CONFIG_USB_MUSB_GADGET
+/* Removing USB gadget and can be enabled adter adding support usb DM */
+#ifndef CONFIG_DM_ETH
+#define CONFIG_USB_ETHER
+#define CONFIG_USB_ETH_RNDIS
+#define CONFIG_USBNET_HOST_ADDR	"de:ad:be:af:00:00"
+#endif /* CONFIG_DM_ETH */
+#endif /* CONFIG_USB_MUSB_GADGET */
+
+
+/*
+ * Disable MMC DM for SPL build and can be re-enabled after adding
+ * DM support in SPL
+ */
+#ifdef CONFIG_SPL_BUILD
+#undef CONFIG_DM_MMC
+#undef CONFIG_TIMER
+#endif
+
+#if defined(CONFIG_SPL_BUILD)
+/* Remove other SPL modes. */
+#undef CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_ENV_IS_NOWHERE
+#undef CONFIG_PARTITION_UUIDS
+#undef CONFIG_EFI_PARTITION
+#endif
+
+/* Network. */
+#define CONFIG_PHY_GIGE
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+#define CONFIG_CLOCK_SYNTHESIZER
+#define CLK_SYNTHESIZER_I2C_ADDR 0x65
+#endif
+
+#define CONFIG_SYS_MEMTEST_START    0x80000000
+#define CONFIG_SYS_MEMTEST_END      0x87900000
+
+#define CONFIG_NM_LOGIN
+#define CONFIG_CRYPT
+
+#if 0
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_DA9063	/* TODO: Provide driver */
+#endif
+
+#define CONFIG_CMD_PXE
+
+#define CONFIG_OF_BOARD_SETUP
+
+#define CONFIG_JTAG_MARKER_SPL		0x402FFF00
+#define CONFIG_JTAG_MARKER_UBOOT	0x807FFF00
+
+/* SPL command is not needed */
+#undef CONFIG_CMD_SPL
+
+/* Never enable ISO it is broken and can lead to a crash */
+#undef CONFIG_ISO_PARTITION
+
+#endif	/* ! __CONFIG_AM335X_NRHW22_H */

include/configs/ti_armv7_common.h

@@ -220,6 +220,7 @@
 
 /* RAW SD card / eMMC locations. */
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR_ALTERNATE 0x1b00 /* address 0x360000  */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
 
 /* FAT sd card locations. */

include/crypt.h

@@ -0,0 +1,6 @@
+#ifndef _CRYPT_H
+#define _CRYPT_H
+
+extern char * sha_crypt(const char *key, const char *salt);
+
+#endif /* _CRYPT_H */

include/image.h

@@ -286,6 +286,14 @@ typedef struct image_header {
 	uint8_t		ih_name[IH_NMLEN];	/* Image Name		*/
 } image_header_t;
 
+typedef struct nm_header {
+	__be32		nm_start_tag; /* BLST (0x424c5354) */
+	__be32		nm_version;  /* U-boot version number */
+	__be32		nm_length;  /* U-boot image length */
+	uint8_t		reserved[244];  /* Reserved */
+	struct image_header header;
+} nm_header_t;
+
 typedef struct image_info {
 	ulong		start, end;		/* start/end of blob */
 	ulong		image_start, image_len; /* start of image within blob, len of image */

lib/Makefile

@@ -20,6 +20,7 @@ obj-$(CONFIG_CMD_DHRYSTONE) += dhry/
 
 obj-$(CONFIG_AES) += aes.o
 obj-$(CONFIG_USB_TTY) += circbuf.o
+obj-$(CONFIG_CRYPT) += crypt.o
 obj-y += crc7.o
 obj-y += crc8.o
 obj-y += crc16.o

lib/crypt.c

@@ -0,0 +1,329 @@
+#include <common.h>
+#include <u-boot/sha256.h>
+#include <malloc.h>
+#include <linux/types.h>
+
+/* The crypt source code was ported from busybox sources pw_crypt */
+
+/* Used by pw_encrypt_XXX.c */
+static const uint8_t ascii64[] = "./0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz";
+static char*
+to64(char *s, unsigned v, int n)
+{
+	while (--n >= 0) {
+		*s++ = ascii64[v & 0x3f];
+		v >>= 6;
+	}
+	return s;
+}
+
+/* SHA256 and SHA512-based Unix crypt implementation.
+ * Released into the Public Domain by Ulrich Drepper <drepper@redhat.com>.
+ */
+
+/* Prefix for optional rounds specification.  */
+static const char str_rounds[] = "rounds=%u$";
+
+/* Maximum salt string length.  */
+#define SALT_LEN_MAX 16
+/* Default number of rounds if not explicitly specified.  */
+#define ROUNDS_DEFAULT 5000
+/* Minimum number of rounds.  */
+#define ROUNDS_MIN 1000
+/* Maximum number of rounds.  */
+#define ROUNDS_MAX 999999999
+
+char *sha_crypt(const char *key_data, const char *salt_data)
+{
+	void (*sha_begin)(void *ctx);
+	void (*sha_hash)(void *ctx, const void *buffer, size_t len);
+	void* (*sha_end)( void *ctx, void *resbuf);
+	int _32or64;
+
+	char *result, *resptr;
+
+	/* btw, sha256 needs [32] and uint32_t only */
+	unsigned char alt_result[64] __attribute__((__aligned__(__alignof__(uint64_t))));
+	unsigned char temp_result[64] __attribute__((__aligned__(__alignof__(uint64_t))));
+	union {
+		sha256_context x;
+    #if 0
+		sha512_ctx_t y;
+    #endif
+	} ctx;
+	union {
+		sha256_context x;
+    #if 0
+		sha512_ctx_t y;
+    #endif
+	} alt_ctx;
+	unsigned salt_len;
+	unsigned key_len;
+	unsigned cnt;
+	unsigned rounds;
+	char *cp;
+	char is_sha512;
+    char *tmp;
+
+	/* Analyze salt, construct already known part of result */
+	cnt = strlen(salt_data) + 1 + 43 + 1;
+	is_sha512 = salt_data[1];
+	if (is_sha512 == '6') {
+        printf("SHA-512 is not supported yet");
+        return 0;
+		/* cnt += 43; */
+    }
+	result = resptr = malloc(cnt); /* will provide NUL terminator */
+    memset(result, 0, cnt);
+	*resptr++ = '$';
+	*resptr++ = is_sha512;
+	*resptr++ = '$';
+	rounds = ROUNDS_DEFAULT;
+	salt_data += 3;
+	if (strncmp(salt_data, str_rounds, 7) == 0) {
+		/* 7 == strlen("rounds=") */
+		char *endp;
+		cnt = simple_strtoul(salt_data + 7, &endp, 10);
+		if (*endp == '$') {
+			salt_data = endp + 1;
+			rounds = cnt;
+			if (rounds < ROUNDS_MIN)
+				rounds = ROUNDS_MIN;
+			if (rounds > ROUNDS_MAX)
+				rounds = ROUNDS_MAX;
+			/* add "rounds=NNNNN$" to result */
+			resptr += sprintf(resptr, str_rounds, rounds);
+		}
+	}
+    {
+        char *salt_end = strchr(salt_data, '$');
+        if (salt_end != 0) {
+            salt_len = salt_end - salt_data;
+        }
+        else {
+          salt_len = strnlen(salt_data, SALT_LEN_MAX);
+        }
+    }
+	// salt_len = (int)strchrnul(salt_data, '$') - (int)salt_data;
+	if (salt_len > SALT_LEN_MAX)
+		salt_len = SALT_LEN_MAX;
+	/* xstrdup assures suitable alignment; also we will use it
+	   as a scratch space later. */
+    tmp = malloc(strnlen(salt_data, 128));
+    memcpy(tmp, salt_data, strnlen(salt_data, 128));
+    salt_data = tmp;
+	//salt_data = xstrndup(salt_data, salt_len);
+	/* add "salt$" to result */
+	strcpy(resptr, salt_data);
+	resptr += salt_len;
+	*resptr++ = '$';
+	/* key data doesn't need much processing */
+	key_len = strlen(key_data);
+    tmp = malloc(strnlen(key_data, 256));
+    memcpy(tmp, key_data, strnlen(key_data, 256));
+    key_data = tmp;
+	// key_data = xstrdup(key_data);
+
+	/* Which flavor of SHAnnn ops to use? */
+	sha_begin = (void*)sha256_starts;
+	sha_hash = (void*)sha256_update;
+	sha_end = (void*)sha256_finish;
+	_32or64 = 32;
+    /* Not supported */
+#if 0
+	if (is_sha512 == '6') {
+		sha_begin = (void*)sha512_begin;
+		sha_hash = (void*)sha512_hash;
+		sha_end = (void*)sha512_end;
+		_32or64 = 64;
+	}
+#endif
+
+	/* Add KEY, SALT.  */
+	sha_begin(&ctx);
+	sha_hash(&ctx, key_data, key_len);
+	sha_hash(&ctx, salt_data, salt_len);
+
+	/* Compute alternate SHA sum with input KEY, SALT, and KEY.
+	   The final result will be added to the first context.  */
+	sha_begin(&alt_ctx);
+	sha_hash(&alt_ctx, key_data, key_len);
+	sha_hash(&alt_ctx, salt_data, salt_len);
+	sha_hash(&alt_ctx, key_data, key_len);
+	sha_end(&alt_ctx, alt_result);
+
+	/* Add result of this to the other context.  */
+	/* Add for any character in the key one byte of the alternate sum.  */
+	for (cnt = key_len; cnt > _32or64; cnt -= _32or64)
+		sha_hash(&ctx, alt_result, _32or64);
+	sha_hash(&ctx, alt_result, cnt);
+
+	/* Take the binary representation of the length of the key and for every
+	   1 add the alternate sum, for every 0 the key.  */
+	for (cnt = key_len; cnt != 0; cnt >>= 1)
+		if ((cnt & 1) != 0)
+			sha_hash(&ctx, alt_result, _32or64);
+		else
+			sha_hash(&ctx, key_data, key_len);
+
+	/* Create intermediate result.  */
+	sha_end(&ctx, alt_result);
+
+	/* Start computation of P byte sequence.  */
+	/* For every character in the password add the entire password.  */
+	sha_begin(&alt_ctx);
+	for (cnt = 0; cnt < key_len; ++cnt)
+		sha_hash(&alt_ctx, key_data, key_len);
+	sha_end(&alt_ctx, temp_result);
+
+	/* NB: past this point, raw key_data is not used anymore */
+
+	/* Create byte sequence P.  */
+#define p_bytes key_data /* reuse the buffer as it is of the key_len size */
+	cp = p_bytes; /* was: ... = alloca(key_len); */
+	for (cnt = key_len; cnt >= _32or64; cnt -= _32or64) {
+		cp = memcpy(cp, temp_result, _32or64);
+		cp += _32or64;
+	}
+	memcpy(cp, temp_result, cnt);
+
+	/* Start computation of S byte sequence.  */
+	/* For every character in the password add the entire password.  */
+	sha_begin(&alt_ctx);
+	for (cnt = 0; cnt < 16 + alt_result[0]; ++cnt)
+		sha_hash(&alt_ctx, salt_data, salt_len);
+	sha_end(&alt_ctx, temp_result);
+
+	/* NB: past this point, raw salt_data is not used anymore */
+
+	/* Create byte sequence S.  */
+#define s_bytes salt_data /* reuse the buffer as it is of the salt_len size */
+	cp = s_bytes; /* was: ... = alloca(salt_len); */
+	for (cnt = salt_len; cnt >= _32or64; cnt -= _32or64) {
+		cp = memcpy(cp, temp_result, _32or64);
+		cp += _32or64;
+	}
+	memcpy(cp, temp_result, cnt);
+
+	/* Repeatedly run the collected hash value through SHA to burn
+	   CPU cycles.  */
+	for (cnt = 0; cnt < rounds; ++cnt) {
+		sha_begin(&ctx);
+
+		/* Add key or last result.  */
+		if ((cnt & 1) != 0)
+			sha_hash(&ctx, p_bytes, key_len);
+		else
+			sha_hash(&ctx, alt_result, _32or64);
+		/* Add salt for numbers not divisible by 3.  */
+		if (cnt % 3 != 0)
+			sha_hash(&ctx, s_bytes, salt_len);
+		/* Add key for numbers not divisible by 7.  */
+		if (cnt % 7 != 0)
+			sha_hash(&ctx, p_bytes, key_len);
+		/* Add key or last result.  */
+		if ((cnt & 1) != 0)
+			sha_hash(&ctx, alt_result, _32or64);
+		else
+			sha_hash(&ctx, p_bytes, key_len);
+
+		sha_end(&ctx, alt_result);
+	}
+
+
+	/* Append encrypted password to result buffer */
+//TODO: replace with something like
+//	bb_uuencode(cp, src, length, bb_uuenc_tbl_XXXbase64);
+#define b64_from_24bit(B2, B1, B0, N) \
+do {							\
+	unsigned w = ((B2) << 16) | ((B1) << 8) | (B0);	\
+	resptr = to64(resptr, w, N);			\
+} while (0)
+	if (is_sha512 == '5') {
+		unsigned i = 0;
+		unsigned j = 10;
+		unsigned k = 20;
+		/* strange swap of one byte (see below why) */
+		unsigned char alt_result_31 = alt_result[31];
+		alt_result[31] = alt_result[1];
+		while (1) {
+			b64_from_24bit(alt_result[i], alt_result[j], alt_result[k], 4);
+			if (i == 9)
+				break;
+			i += 21; i = (((i >> 4) & 2) + i) & 0x1f;
+			j += 21; j = (((j >> 4) & 2) + j) & 0x1f;
+			k += 21; k = (((k >> 4) & 2) + k) & 0x1f;
+		}
+		b64_from_24bit(0, alt_result_31, alt_result[30], 3);
+		/* was:
+		b64_from_24bit(alt_result[0], alt_result[10], alt_result[20], 4);
+		b64_from_24bit(alt_result[21], alt_result[1], alt_result[11], 4);
+		...............................^^^^^^^^^^^^^ why [1] and not [31]?
+		b64_from_24bit(alt_result[12], alt_result[22], alt_result[2], 4);
+		b64_from_24bit(alt_result[3], alt_result[13], alt_result[23], 4);
+		b64_from_24bit(alt_result[24], alt_result[4], alt_result[14], 4);
+		b64_from_24bit(alt_result[15], alt_result[25], alt_result[5], 4);
+		b64_from_24bit(alt_result[6], alt_result[16], alt_result[26], 4);
+		b64_from_24bit(alt_result[27], alt_result[7], alt_result[17], 4);
+		b64_from_24bit(alt_result[18], alt_result[28], alt_result[8], 4);
+		b64_from_24bit(alt_result[9], alt_result[19], alt_result[29], 4);
+		b64_from_24bit(0, alt_result[31], alt_result[30], 3);
+		*/
+	} else {
+		unsigned i = 0;
+		unsigned j = 21;
+		unsigned k = 42;
+		while (1) {
+			b64_from_24bit(alt_result[i], alt_result[j], alt_result[k], 4);
+			if (i == 62)
+				break;
+			i += 22; i = ((i >> 6) + i) & 0x3f;
+			j += 22; j = ((j >> 6) + j) & 0x3f;
+			k += 22; k = ((k >> 6) + k) & 0x3f;
+		}
+		b64_from_24bit(0, 0, alt_result[63], 2);
+		/* was:
+		b64_from_24bit(alt_result[0], alt_result[21], alt_result[42], 4);
+		b64_from_24bit(alt_result[22], alt_result[43], alt_result[1], 4);
+		b64_from_24bit(alt_result[44], alt_result[2], alt_result[23], 4);
+		b64_from_24bit(alt_result[3], alt_result[24], alt_result[45], 4);
+		b64_from_24bit(alt_result[25], alt_result[46], alt_result[4], 4);
+		b64_from_24bit(alt_result[47], alt_result[5], alt_result[26], 4);
+		b64_from_24bit(alt_result[6], alt_result[27], alt_result[48], 4);
+		b64_from_24bit(alt_result[28], alt_result[49], alt_result[7], 4);
+		b64_from_24bit(alt_result[50], alt_result[8], alt_result[29], 4);
+		b64_from_24bit(alt_result[9], alt_result[30], alt_result[51], 4);
+		b64_from_24bit(alt_result[31], alt_result[52], alt_result[10], 4);
+		b64_from_24bit(alt_result[53], alt_result[11], alt_result[32], 4);
+		b64_from_24bit(alt_result[12], alt_result[33], alt_result[54], 4);
+		b64_from_24bit(alt_result[34], alt_result[55], alt_result[13], 4);
+		b64_from_24bit(alt_result[56], alt_result[14], alt_result[35], 4);
+		b64_from_24bit(alt_result[15], alt_result[36], alt_result[57], 4);
+		b64_from_24bit(alt_result[37], alt_result[58], alt_result[16], 4);
+		b64_from_24bit(alt_result[59], alt_result[17], alt_result[38], 4);
+		b64_from_24bit(alt_result[18], alt_result[39], alt_result[60], 4);
+		b64_from_24bit(alt_result[40], alt_result[61], alt_result[19], 4);
+		b64_from_24bit(alt_result[62], alt_result[20], alt_result[41], 4);
+		b64_from_24bit(0, 0, alt_result[63], 2);
+		*/
+	}
+	/* *resptr = '\0'; - xzalloc did it */
+#undef b64_from_24bit
+
+	/* Clear the buffer for the intermediate result so that people
+	   attaching to processes or reading core dumps cannot get any
+	   information.  */
+	memset(temp_result, 0, sizeof(temp_result));
+	memset(alt_result, 0, sizeof(alt_result));
+	memset(&ctx, 0, sizeof(ctx));
+	memset(&alt_ctx, 0, sizeof(alt_ctx));
+	memset(key_data, 0, key_len); /* also p_bytes */
+	memset(salt_data, 0, salt_len); /* also s_bytes */
+	free(key_data);
+	free(salt_data);
+#undef p_bytes
+#undef s_bytes
+
+	return result;
+}
+

lib/display_options.c

@@ -12,13 +12,15 @@
 #include <version.h>
 #include <linux/ctype.h>
 #include <asm/io.h>
+#include <version_autogenerated.h>
 
 int display_options (void)
 {
+	printf ("\n\n%s\n", UBOOT_VERSION);
 #if defined(BUILD_TAG)
-	printf ("\n\n%s, Build: %s\n\n", version_string, BUILD_TAG);
+	printf ("%s, Build: %s\n\n", version_string, BUILD_TAG);
 #else
-	printf ("\n\n%s\n\n", version_string);
+	printf ("%s\n\n", version_string);
 #endif
 	return 0;
 }

pack

@@ -0,0 +1,37 @@
+#!/bin/bash
+
+UB_VERSION="0.0.0.0"
+
+TOP_DIR="."
+BIN_DIR="$TOP_DIR/bin"
+TEMP_DIR=$BIN_DIR/temp
+
+START_MAGIC=424c5354
+END_MAGIC=424c454e
+
+LOADER_VERSION=$(echo $UB_VERSION | awk -F'.' '{ printf "%02X%02X%02x%02X", $$1, $$2, $$3, $$4; }')
+
+rm -rf $BIN_DIR
+rm -rf $TEMP_DIR
+
+mkdir -p $BIN_DIR
+mkdir -p $TEMP_DIR
+
+dd if=$TOP_DIR/MLO of=$TEMP_DIR/MLO-start bs=480 count=1
+dd if=$TOP_DIR/MLO of=$TEMP_DIR/MLO-end skip=512 bs=1
+echo -ne "SPL V$UB_VERSION\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0" | dd of=$TEMP_DIR/MLO-version count=1 bs=32
+cat $TEMP_DIR/MLO-start $TEMP_DIR/MLO-version $TEMP_DIR/MLO-end > $BIN_DIR/emmc-spl
+
+echo $START_MAGIC | xxd -p -l 4 -r > $TEMP_DIR/startMagic.bin
+echo $END_MAGIC | xxd -p -l 4 -r > $TEMP_DIR/endMagic.bin
+echo $LOADER_VERSION | xxd -p -l 4 -r > $TEMP_DIR/loaderVersion.bin
+cat $TOP_DIR/u-boot.img | wc -c | sed "s/.*/obase=16\n\0/" | bc | sed "s/.*/0000000\0/" | tail -c 9 | xxd -p -l 4 -r > $TEMP_DIR/imageSize.bin
+echo f4:0 | xxd -r | xxd | xxd -r > $TEMP_DIR/reserved.bin
+cat $TEMP_DIR/startMagic.bin $TEMP_DIR/loaderVersion.bin $TEMP_DIR/imageSize.bin $TEMP_DIR/reserved.bin $TOP_DIR/u-boot.img $TEMP_DIR/endMagic.bin > $BIN_DIR/emmc-uboot
+
+cp $TOP_DIR/spl/u-boot-spl.bin $BIN_DIR/xmodem-spl
+cp $TOP_DIR/u-boot.bin $BIN_DIR/xmodem-uboot
+
+rm -rf $TEMP_DIR
+
+chmod 0666 $BIN_DIR/*