290 lines
6.7 KiB
C
290 lines
6.7 KiB
C
/*
|
|
* Copyright 2013 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <command.h>
|
|
#include <hwconfig.h>
|
|
#include <pci.h>
|
|
#include <i2c.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/mmu.h>
|
|
#include <asm/cache.h>
|
|
#include <asm/immap_85xx.h>
|
|
#include <asm/fsl_pci.h>
|
|
#include <fsl_ddr_sdram.h>
|
|
#include <asm/io.h>
|
|
#include <asm/fsl_law.h>
|
|
#include <asm/fsl_lbc.h>
|
|
#include <asm/mp.h>
|
|
#include <miiphy.h>
|
|
#include <libfdt.h>
|
|
#include <fdt_support.h>
|
|
#include <fsl_mdio.h>
|
|
#include <tsec.h>
|
|
#include <ioports.h>
|
|
#include <asm/fsl_serdes.h>
|
|
#include <netdev.h>
|
|
|
|
#define SYSCLK_64 64000000
|
|
#define SYSCLK_66 66666666
|
|
|
|
unsigned long get_board_sys_clk(ulong dummy)
|
|
{
|
|
ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
par_io_t *par_io = (par_io_t *) &(gur->qe_par_io);
|
|
unsigned int cpdat_val = 0;
|
|
|
|
/* Set-up up pin muxing based on board switch settings */
|
|
cpdat_val = par_io[1].cpdat;
|
|
|
|
/* Check switch setting for SYSCLK select (PB3) */
|
|
if (cpdat_val & 0x10000000)
|
|
return SYSCLK_64;
|
|
else
|
|
return SYSCLK_66;
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_QE
|
|
|
|
#define PCA_IOPORT_I2C_ADDR 0x23
|
|
#define PCA_IOPORT_OUTPUT_CMD 0x2
|
|
#define PCA_IOPORT_CFG_CMD 0x6
|
|
|
|
const qe_iop_conf_t qe_iop_conf_tab[] = {
|
|
|
|
#ifdef CONFIG_TWR_P1025
|
|
/* GPIO */
|
|
{1, 0, 1, 0, 0},
|
|
{1, 18, 1, 0, 0},
|
|
|
|
/* GPIO for switch options */
|
|
{1, 2, 2, 0, 0}, /* PROFIBUS_MODE_SEL */
|
|
{1, 3, 2, 0, 0}, /* SYS_CLK_SELECT */
|
|
{1, 29, 2, 0, 0}, /* LOCALBUS_QE_MUXSEL */
|
|
{1, 30, 2, 0, 0}, /* ETH_TDM_SEL */
|
|
|
|
/* QE_MUX_MDC */
|
|
{1, 19, 1, 0, 1}, /* QE_MUX_MDC */
|
|
|
|
/* QE_MUX_MDIO */
|
|
{1, 20, 3, 0, 1}, /* QE_MUX_MDIO */
|
|
|
|
/* UCC_1_MII */
|
|
{0, 23, 2, 0, 2}, /* CLK12 */
|
|
{0, 24, 2, 0, 1}, /* CLK9 */
|
|
{0, 7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0 */
|
|
{0, 9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1 */
|
|
{0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2 */
|
|
{0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3 */
|
|
{0, 6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0 */
|
|
{0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1 */
|
|
{0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2 */
|
|
{0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3 */
|
|
{0, 5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B */
|
|
{0, 13, 1, 0, 2}, /* ENET1_TX_ER */
|
|
{0, 4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B */
|
|
{0, 8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B */
|
|
{0, 17, 2, 0, 2}, /* ENET1_CRS */
|
|
{0, 16, 2, 0, 2}, /* ENET1_COL */
|
|
|
|
/* UCC_5_RMII */
|
|
{1, 11, 2, 0, 1}, /* CLK13 */
|
|
{1, 7, 1, 0, 2}, /* ENET5_TXD0_SER5_TXD0 */
|
|
{1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1 */
|
|
{1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0 */
|
|
{1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1 */
|
|
{1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B */
|
|
{1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B */
|
|
{1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B */
|
|
|
|
/* TDMA - clock option is configured in OS based on board setting */
|
|
{1, 23, 2, 0, 2}, /* TDMA_TXD */
|
|
{1, 25, 2, 0, 2}, /* TDMA_RXD */
|
|
{1, 26, 1, 0, 2}, /* TDMA_SYNC */
|
|
#endif
|
|
|
|
{0, 0, 0, 0, QE_IOP_TAB_END} /* END of table */
|
|
};
|
|
#endif
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
|
|
setbits_be32(&gur->pmuxcr,
|
|
(MPC85xx_PMUXCR_SDHC_CD | MPC85xx_PMUXCR_SDHC_WP));
|
|
|
|
/* SDHC_DAT[4:7] not exposed to pins (use as SPI) */
|
|
clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
u8 boot_status;
|
|
|
|
printf("Board: %s\n", CONFIG_BOARDNAME);
|
|
|
|
boot_status = ((gur->porbmsr) >> MPC85xx_PORBMSR_ROMLOC_SHIFT) & 0xf;
|
|
puts("rom_loc: ");
|
|
if (boot_status == PORBMSR_ROMLOC_NOR)
|
|
puts("nor flash");
|
|
else if (boot_status == PORBMSR_ROMLOC_SDHC)
|
|
puts("sd");
|
|
else
|
|
puts("unknown");
|
|
puts("\n");
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PCI
|
|
void pci_init_board(void)
|
|
{
|
|
fsl_pcie_init_board(0);
|
|
}
|
|
#endif
|
|
|
|
int board_early_init_r(void)
|
|
{
|
|
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
|
|
int flash_esel = find_tlb_idx((void *)flashbase, 1);
|
|
|
|
/*
|
|
* Remap Boot flash region to caching-inhibited
|
|
* so that flash can be erased properly.
|
|
*/
|
|
|
|
/* Flush d-cache and invalidate i-cache of any FLASH data */
|
|
flush_dcache();
|
|
invalidate_icache();
|
|
|
|
if (flash_esel == -1) {
|
|
/* very unlikely unless something is messed up */
|
|
puts("Error: Could not find TLB for FLASH BASE\n");
|
|
flash_esel = 2; /* give our best effort to continue */
|
|
} else {
|
|
/* invalidate existing TLB entry for flash */
|
|
disable_tlb(flash_esel);
|
|
}
|
|
|
|
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, /* tlb, epn, rpn */
|
|
MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, /* perms, wimge */
|
|
0, flash_esel, BOOKE_PAGESZ_64M, 1);/* ts, esel, tsize, iprot */
|
|
return 0;
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
struct fsl_pq_mdio_info mdio_info;
|
|
struct tsec_info_struct tsec_info[4];
|
|
ccsr_gur_t *gur __attribute__((unused)) =
|
|
(void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
|
int num = 0;
|
|
|
|
#ifdef CONFIG_TSEC1
|
|
SET_STD_TSEC_INFO(tsec_info[num], 1);
|
|
num++;
|
|
#endif
|
|
#ifdef CONFIG_TSEC2
|
|
SET_STD_TSEC_INFO(tsec_info[num], 2);
|
|
if (is_serdes_configured(SGMII_TSEC2)) {
|
|
printf("eTSEC2 is in sgmii mode.\n");
|
|
tsec_info[num].flags |= TSEC_SGMII;
|
|
}
|
|
num++;
|
|
#endif
|
|
#ifdef CONFIG_TSEC3
|
|
SET_STD_TSEC_INFO(tsec_info[num], 3);
|
|
num++;
|
|
#endif
|
|
|
|
if (!num) {
|
|
printf("No TSECs initialized\n");
|
|
return 0;
|
|
}
|
|
|
|
mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
|
|
mdio_info.name = DEFAULT_MII_NAME;
|
|
|
|
fsl_pq_mdio_init(bis, &mdio_info);
|
|
|
|
tsec_eth_init(bis, tsec_info, num);
|
|
|
|
#if defined(CONFIG_UEC_ETH)
|
|
/* QE0 and QE3 need to be exposed for UCC1
|
|
* and UCC5 Eth mode (in PMUXCR register).
|
|
* Currently QE/LBC muxed pins assumed to be
|
|
* LBC for U-Boot and PMUXCR updated by OS if required */
|
|
|
|
uec_standard_init(bis);
|
|
#endif
|
|
|
|
return pci_eth_init(bis);
|
|
}
|
|
|
|
#if defined(CONFIG_QE)
|
|
static void fdt_board_fixup_qe_pins(void *blob)
|
|
{
|
|
int node;
|
|
|
|
if (!hwconfig("qe")) {
|
|
/* For QE and eLBC pins multiplexing,
|
|
* When don't use QE function, remove
|
|
* qe node from dt blob.
|
|
*/
|
|
node = fdt_path_offset(blob, "/qe");
|
|
if (node >= 0)
|
|
fdt_del_node(blob, node);
|
|
} else {
|
|
/* For TWR Peripheral Modules - TWR-SER2
|
|
* board only can support Signal Port MII,
|
|
* so delete one UEC node when use MII port.
|
|
*/
|
|
if (hwconfig("mii"))
|
|
node = fdt_path_offset(blob, "/qe/ucc@2400");
|
|
else
|
|
node = fdt_path_offset(blob, "/qe/ucc@2000");
|
|
if (node >= 0)
|
|
fdt_del_node(blob, node);
|
|
}
|
|
|
|
return;
|
|
}
|
|
#endif
|
|
|
|
#ifdef CONFIG_OF_BOARD_SETUP
|
|
int ft_board_setup(void *blob, bd_t *bd)
|
|
{
|
|
phys_addr_t base;
|
|
phys_size_t size;
|
|
|
|
ft_cpu_setup(blob, bd);
|
|
|
|
base = getenv_bootm_low();
|
|
size = getenv_bootm_size();
|
|
|
|
fdt_fixup_memory(blob, (u64)base, (u64)size);
|
|
|
|
FT_FSL_PCI_SETUP;
|
|
|
|
#ifdef CONFIG_QE
|
|
do_fixup_by_compat(blob, "fsl,qe", "status", "okay",
|
|
sizeof("okay"), 0);
|
|
#endif
|
|
#if defined(CONFIG_TWR_P1025)
|
|
fdt_board_fixup_qe_pins(blob);
|
|
#endif
|
|
fdt_fixup_dr_usb(blob, bd);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|