The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
#
# Xilinx ZYNQ U-Boot
#
# (C) Copyright 2013 Xilinx, Inc.
#
# SPDX-License-Identifier: GPL-2.0+
#
1. About this
This document describes the information about Xilinx Zynq U-Boot -
like supported boards, ML status and TODO list.
2. Zynq boards
Xilinx Zynq-7000 All Programmable SoCs enable extensive system level
differentiation, integration, and flexibility through hardware, software,
and I/O programmability.
* zc702 (single qspi, gem0, mmc) [1]
* zc706 (dual parallel qspi, gem0, mmc) [2]
* zed (single qspi, gem0, mmc) [3]
* microzed (single qspi, gem0, mmc) [4]
* zc770
- zc770-xm010 (single qspi, gem0, mmc)
- zc770-xm011 (8 or 16 bit nand)
- zc770-xm012 (nor)
- zc770-xm013 (dual parallel qspi, gem1)
3. Building
ex. configure and build for zc702 board
$ make zynq_zc702_config
$ make
4. Bootmode
Zynq has a facility to read the bootmode from the slcr bootmode register
once user is setting through jumpers on the board - see page no:1546 on [5]
All possible bootmode values are defined in Table 6-2:Boot_Mode MIO Pins
on [5].
board_late_init() will read the bootmode values using slcr bootmode register
at runtime and assign the modeboot variable to specific bootmode string which
is intern used in autoboot.
SLCR bootmode register Bit[3:0] values
#define ZYNQ_BM_NOR 0x02
#define ZYNQ_BM_SD 0x05
#define ZYNQ_BM_JTAG 0x0
"modeboot" variable can assign any of "norboot", "sdboot" or "jtagboot"
bootmode strings at runtime.
5. Mainline status
- Added basic board configurations support.
- Added zynq u-boot bsp code - arch/arm/cpu/armv7/zynq
- Added zynq boards named - zc70x, zed, microzed, zc770_xm010, zc770_xm012, zc770_xm013
- Added zynq drivers:
serial - drivers/serial/serial_zynq.c
net - drivers/net/zynq_gem.c
mmc - drivers/mmc/zynq_sdhci.c
mmc - drivers/mmc/zynq_sdhci.c
spi- drivers/spi/zynq_spi.c
i2c - drivers/i2c/zynq_i2c.c
- Done proper cleanups on board configurations
- Added basic FDT support for zynq boards
- d-cache support for zynq_gem.c
6. TODO
- Add zynq boards support - zc770_xm011
- Add zynq qspi controller driver
- Add zynq nand controller driver
- Add FDT support on individual drivers
[1] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC702-G.htm
[2] http://www.xilinx.com/products/boards-and-kits/EK-Z7-ZC706-G.htm
[3] http://zedboard.org/product/zedboard
[4] http://zedboard.org/product/microzed
[5] http://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf
--
Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Sun Dec 15 14:52:41 IST 2013
a95aee6af7