1599 lines
		
	
	
		
			45 KiB
		
	
	
	
		
			C
		
	
	
	
			
		
		
	
	
			1599 lines
		
	
	
		
			45 KiB
		
	
	
	
		
			C
		
	
	
	
| /*
 | |
|  * Broadcom BCM570x Ethernet Driver for U-Boot.
 | |
|  * Support 5701, 5702, 5703, and 5704. Single instance driver.
 | |
|  * Copyright (C) 2002 James F. Dougherty (jfd@broadcom.com)
 | |
|  */
 | |
| 
 | |
| #include <common.h>
 | |
| 
 | |
| #ifdef CONFIG_BMW
 | |
| #include <mpc824x.h>
 | |
| #endif
 | |
| #include <net.h>
 | |
| #include "bcm570x_mm.h"
 | |
| #include "bcm570x_autoneg.h"
 | |
| #include <pci.h>
 | |
| #include <malloc.h>
 | |
| 
 | |
| /*
 | |
|  * PCI Registers and definitions.
 | |
|  */
 | |
| #define PCI_CMD_MASK	0xffff0000	/* mask to save status bits */
 | |
| #define PCI_ANY_ID (~0)
 | |
| 
 | |
| /*
 | |
|  * PCI memory base for Ethernet device as well as device Interrupt.
 | |
|  */
 | |
| #define BCM570X_MBAR	0x80100000
 | |
| #define BCM570X_ILINE   1
 | |
| 
 | |
| #define SECOND_USEC	1000000
 | |
| #define MAX_PACKET_SIZE 1600
 | |
| #define MAX_UNITS       4
 | |
| 
 | |
| /* Globals to this module */
 | |
| int initialized = 0;
 | |
| unsigned int ioBase = 0;
 | |
| volatile PLM_DEVICE_BLOCK pDevice = NULL;	/* 570x softc */
 | |
| volatile PUM_DEVICE_BLOCK pUmDevice = NULL;
 | |
| 
 | |
| /* Used to pass the full-duplex flag, etc. */
 | |
| int line_speed[MAX_UNITS] = { 0, 0, 0, 0 };
 | |
| static int full_duplex[MAX_UNITS] = { 1, 1, 1, 1 };
 | |
| static int rx_flow_control[MAX_UNITS] = { 0, 0, 0, 0 };
 | |
| static int tx_flow_control[MAX_UNITS] = { 0, 0, 0, 0 };
 | |
| static int auto_flow_control[MAX_UNITS] = { 0, 0, 0, 0 };
 | |
| static int tx_checksum[MAX_UNITS] = { 1, 1, 1, 1 };
 | |
| static int rx_checksum[MAX_UNITS] = { 1, 1, 1, 1 };
 | |
| static int auto_speed[MAX_UNITS] = { 1, 1, 1, 1 };
 | |
| 
 | |
| #if JUMBO_FRAMES
 | |
| /* Jumbo MTU for interfaces. */
 | |
| static int mtu[MAX_UNITS] = { 0, 0, 0, 0 };
 | |
| #endif
 | |
| 
 | |
| /* Turn on Wake-on lan for a device unit */
 | |
| static int enable_wol[MAX_UNITS] = { 0, 0, 0, 0 };
 | |
| 
 | |
| #define TX_DESC_CNT DEFAULT_TX_PACKET_DESC_COUNT
 | |
| static unsigned int tx_pkt_desc_cnt[MAX_UNITS] =
 | |
|     { TX_DESC_CNT, TX_DESC_CNT, TX_DESC_CNT, TX_DESC_CNT };
 | |
| 
 | |
| #define RX_DESC_CNT DEFAULT_STD_RCV_DESC_COUNT
 | |
| static unsigned int rx_std_desc_cnt[MAX_UNITS] =
 | |
|     { RX_DESC_CNT, RX_DESC_CNT, RX_DESC_CNT, RX_DESC_CNT };
 | |
| 
 | |
| static unsigned int rx_adaptive_coalesce[MAX_UNITS] = { 1, 1, 1, 1 };
 | |
| 
 | |
| #if T3_JUMBO_RCV_RCB_ENTRY_COUNT
 | |
| #define JBO_DESC_CNT DEFAULT_JUMBO_RCV_DESC_COUNT
 | |
| static unsigned int rx_jumbo_desc_cnt[MAX_UNITS] =
 | |
|     { JBO_DESC_CNT, JBO_DESC_CNT, JBO_DESC_CNT, JBO_DESC_CNT };
 | |
| #endif
 | |
| #define RX_COAL_TK DEFAULT_RX_COALESCING_TICKS
 | |
| static unsigned int rx_coalesce_ticks[MAX_UNITS] =
 | |
|     { RX_COAL_TK, RX_COAL_TK, RX_COAL_TK, RX_COAL_TK };
 | |
| 
 | |
| #define RX_COAL_FM DEFAULT_RX_MAX_COALESCED_FRAMES
 | |
| static unsigned int rx_max_coalesce_frames[MAX_UNITS] =
 | |
|     { RX_COAL_FM, RX_COAL_FM, RX_COAL_FM, RX_COAL_FM };
 | |
| 
 | |
| #define TX_COAL_TK DEFAULT_TX_COALESCING_TICKS
 | |
| static unsigned int tx_coalesce_ticks[MAX_UNITS] =
 | |
|     { TX_COAL_TK, TX_COAL_TK, TX_COAL_TK, TX_COAL_TK };
 | |
| 
 | |
| #define TX_COAL_FM DEFAULT_TX_MAX_COALESCED_FRAMES
 | |
| static unsigned int tx_max_coalesce_frames[MAX_UNITS] =
 | |
|     { TX_COAL_FM, TX_COAL_FM, TX_COAL_FM, TX_COAL_FM };
 | |
| 
 | |
| #define ST_COAL_TK DEFAULT_STATS_COALESCING_TICKS
 | |
| static unsigned int stats_coalesce_ticks[MAX_UNITS] =
 | |
|     { ST_COAL_TK, ST_COAL_TK, ST_COAL_TK, ST_COAL_TK };
 | |
| 
 | |
| /*
 | |
|  * Legitimate values for BCM570x device types
 | |
|  */
 | |
| typedef enum {
 | |
| 	BCM5700VIGIL = 0,
 | |
| 	BCM5700A6,
 | |
| 	BCM5700T6,
 | |
| 	BCM5700A9,
 | |
| 	BCM5700T9,
 | |
| 	BCM5700,
 | |
| 	BCM5701A5,
 | |
| 	BCM5701T1,
 | |
| 	BCM5701T8,
 | |
| 	BCM5701A7,
 | |
| 	BCM5701A10,
 | |
| 	BCM5701A12,
 | |
| 	BCM5701,
 | |
| 	BCM5702,
 | |
| 	BCM5703,
 | |
| 	BCM5703A31,
 | |
| 	TC996T,
 | |
| 	TC996ST,
 | |
| 	TC996SSX,
 | |
| 	TC996SX,
 | |
| 	TC996BT,
 | |
| 	TC997T,
 | |
| 	TC997SX,
 | |
| 	TC1000T,
 | |
| 	TC940BR01,
 | |
| 	TC942BR01,
 | |
| 	NC6770,
 | |
| 	NC7760,
 | |
| 	NC7770,
 | |
| 	NC7780
 | |
| } board_t;
 | |
| 
 | |
| /* Chip-Rev names for each device-type */
 | |
| static struct {
 | |
| 	char *name;
 | |
| } chip_rev[] = {
 | |
| 	{
 | |
| 	"BCM5700VIGIL"}, {
 | |
| 	"BCM5700A6"}, {
 | |
| 	"BCM5700T6"}, {
 | |
| 	"BCM5700A9"}, {
 | |
| 	"BCM5700T9"}, {
 | |
| 	"BCM5700"}, {
 | |
| 	"BCM5701A5"}, {
 | |
| 	"BCM5701T1"}, {
 | |
| 	"BCM5701T8"}, {
 | |
| 	"BCM5701A7"}, {
 | |
| 	"BCM5701A10"}, {
 | |
| 	"BCM5701A12"}, {
 | |
| 	"BCM5701"}, {
 | |
| 	"BCM5702"}, {
 | |
| 	"BCM5703"}, {
 | |
| 	"BCM5703A31"}, {
 | |
| 	"TC996T"}, {
 | |
| 	"TC996ST"}, {
 | |
| 	"TC996SSX"}, {
 | |
| 	"TC996SX"}, {
 | |
| 	"TC996BT"}, {
 | |
| 	"TC997T"}, {
 | |
| 	"TC997SX"}, {
 | |
| 	"TC1000T"}, {
 | |
| 	"TC940BR01"}, {
 | |
| 	"TC942BR01"}, {
 | |
| 	"NC6770"}, {
 | |
| 	"NC7760"}, {
 | |
| 	"NC7770"}, {
 | |
| 	"NC7780"}, {
 | |
| 	0}
 | |
| };
 | |
| 
 | |
| /* indexed by board_t, above */
 | |
| static struct {
 | |
| 	char *name;
 | |
| } board_info[] = {
 | |
| 	{
 | |
| 	"Broadcom Vigil B5700 1000Base-T"}, {
 | |
| 	"Broadcom BCM5700 1000Base-T"}, {
 | |
| 	"Broadcom BCM5700 1000Base-SX"}, {
 | |
| 	"Broadcom BCM5700 1000Base-SX"}, {
 | |
| 	"Broadcom BCM5700 1000Base-T"}, {
 | |
| 	"Broadcom BCM5700"}, {
 | |
| 	"Broadcom BCM5701 1000Base-T"}, {
 | |
| 	"Broadcom BCM5701 1000Base-T"}, {
 | |
| 	"Broadcom BCM5701 1000Base-T"}, {
 | |
| 	"Broadcom BCM5701 1000Base-SX"}, {
 | |
| 	"Broadcom BCM5701 1000Base-T"}, {
 | |
| 	"Broadcom BCM5701 1000Base-T"}, {
 | |
| 	"Broadcom BCM5701"}, {
 | |
| 	"Broadcom BCM5702 1000Base-T"}, {
 | |
| 	"Broadcom BCM5703 1000Base-T"}, {
 | |
| 	"Broadcom BCM5703 1000Base-SX"}, {
 | |
| 	"3Com 3C996 10/100/1000 Server NIC"}, {
 | |
| 	"3Com 3C996 10/100/1000 Server NIC"}, {
 | |
| 	"3Com 3C996 Gigabit Fiber-SX Server NIC"}, {
 | |
| 	"3Com 3C996 Gigabit Fiber-SX Server NIC"}, {
 | |
| 	"3Com 3C996B Gigabit Server NIC"}, {
 | |
| 	"3Com 3C997 Gigabit Server NIC"}, {
 | |
| 	"3Com 3C997 Gigabit Fiber-SX Server NIC"}, {
 | |
| 	"3Com 3C1000 Gigabit NIC"}, {
 | |
| 	"3Com 3C940 Gigabit LOM (21X21)"}, {
 | |
| 	"3Com 3C942 Gigabit LOM (31X31)"}, {
 | |
| 	"Compaq NC6770 Gigabit Server Adapter"}, {
 | |
| 	"Compaq NC7760 Gigabit Server Adapter"}, {
 | |
| 	"Compaq NC7770 Gigabit Server Adapter"}, {
 | |
| 	"Compaq NC7780 Gigabit Server Adapter"}, {
 | |
| 0},};
 | |
| 
 | |
| /* PCI Devices which use the 570x chipset */
 | |
| struct pci_device_table {
 | |
| 	unsigned short vendor_id, device_id;	/* Vendor/DeviceID */
 | |
| 	unsigned short subvendor, subdevice;	/* Subsystem ID's or PCI_ANY_ID */
 | |
| 	unsigned int class, class_mask;	/* (class,subclass,prog-if) triplet */
 | |
| 	unsigned long board_id;	/* Data private to the driver */
 | |
| 	int io_size, min_latency;
 | |
| } bcm570xDevices[] = {
 | |
| 	{
 | |
| 	0x14e4, 0x1644, 0x1014, 0x0277, 0, 0, BCM5700VIGIL, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x14e4, 0x1644, 0, 0, BCM5700A6, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x14e4, 0x2, 0, 0, BCM5700T6, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x14e4, 0x3, 0, 0, BCM5700A9, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x14e4, 0x4, 0, 0, BCM5700T9, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x1028, 0xd1, 0, 0, BCM5700, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x1028, 0x0106, 0, 0, BCM5700, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x1028, 0x0109, 0, 0, BCM5700, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x1028, 0x010a, 0, 0, BCM5700, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x10b7, 0x1000, 0, 0, TC996T, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x10b7, 0x1001, 0, 0, TC996ST, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x10b7, 0x1002, 0, 0, TC996SSX, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x10b7, 0x1003, 0, 0, TC997T, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x10b7, 0x1005, 0, 0, TC997SX, 128, 32}, {
 | |
| 	0x14e4, 0x1644, 0x10b7, 0x1008, 0, 0, TC942BR01, 128, 32}, {
 | |
| 	0x14e4, 0x1644, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5700, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x14e4, 1, 0, 0, BCM5701A5, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x14e4, 5, 0, 0, BCM5701T1, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x14e4, 6, 0, 0, BCM5701T8, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x14e4, 7, 0, 0, BCM5701A7, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x14e4, 8, 0, 0, BCM5701A10, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x14e4, 0x8008, 0, 0, BCM5701A12, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x0e11, 0xc1, 0, 0, NC6770, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x0e11, 0x7c, 0, 0, NC7770, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x0e11, 0x85, 0, 0, NC7780, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x1028, 0x0121, 0, 0, BCM5701, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x10b7, 0x1004, 0, 0, TC996SX, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x10b7, 0x1006, 0, 0, TC996BT, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x10b7, 0x1007, 0, 0, TC1000T, 128, 32}, {
 | |
| 	0x14e4, 0x1645, 0x10b7, 0x1008, 0, 0, TC940BR01, 128, 32}, {
 | |
| 	0x14e4, 0x1645, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5701, 128, 32}, {
 | |
| 	0x14e4, 0x1646, 0x14e4, 0x8009, 0, 0, BCM5702, 128, 32}, {
 | |
| 	0x14e4, 0x1646, 0x0e11, 0xbb, 0, 0, NC7760, 128, 32}, {
 | |
| 	0x14e4, 0x1646, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5702, 128, 32}, {
 | |
| 	0x14e4, 0x16a6, 0x14e4, 0x8009, 0, 0, BCM5702, 128, 32}, {
 | |
| 	0x14e4, 0x16a6, 0x0e11, 0xbb, 0, 0, NC7760, 128, 32}, {
 | |
| 	0x14e4, 0x16a6, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5702, 128, 32}, {
 | |
| 	0x14e4, 0x1647, 0x14e4, 0x0009, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x1647, 0x14e4, 0x000a, 0, 0, BCM5703A31, 128, 32}, {
 | |
| 	0x14e4, 0x1647, 0x14e4, 0x000b, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x1647, 0x14e4, 0x800a, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x1647, 0x0e11, 0x9a, 0, 0, NC7770, 128, 32}, {
 | |
| 	0x14e4, 0x1647, 0x0e11, 0x99, 0, 0, NC7780, 128, 32}, {
 | |
| 	0x14e4, 0x1647, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, 0x14e4, 0x0009, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, 0x14e4, 0x000a, 0, 0, BCM5703A31, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, 0x14e4, 0x000b, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, 0x14e4, 0x800a, 0, 0, BCM5703, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, 0x0e11, 0x9a, 0, 0, NC7770, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, 0x0e11, 0x99, 0, 0, NC7780, 128, 32}, {
 | |
| 	0x14e4, 0x16a7, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BCM5703, 128, 32}
 | |
| };
 | |
| 
 | |
| #define n570xDevices   (sizeof(bcm570xDevices)/sizeof(bcm570xDevices[0]))
 | |
| 
 | |
| /*
 | |
|  * Allocate a packet buffer from the bcm570x packet pool.
 | |
|  */
 | |
| void *bcm570xPktAlloc (int u, int pksize)
 | |
| {
 | |
| 	return malloc (pksize);
 | |
| }
 | |
| 
 | |
| /*
 | |
|  * Free a packet previously allocated from the bcm570x packet
 | |
|  * buffer pool.
 | |
|  */
 | |
| void bcm570xPktFree (int u, void *p)
 | |
| {
 | |
| 	free (p);
 | |
| }
 | |
| 
 | |
| int bcm570xReplenishRxBuffers (PUM_DEVICE_BLOCK pUmDevice)
 | |
| {
 | |
| 	PLM_PACKET pPacket;
 | |
| 	PUM_PACKET pUmPacket;
 | |
| 	void *skb;
 | |
| 	int queue_rx = 0;
 | |
| 	int ret = 0;
 | |
| 
 | |
| 	while ((pUmPacket = (PUM_PACKET)
 | |
| 		QQ_PopHead (&pUmDevice->rx_out_of_buf_q.Container)) != 0) {
 | |
| 
 | |
| 		pPacket = (PLM_PACKET) pUmPacket;
 | |
| 
 | |
| 		/* reuse an old skb */
 | |
| 		if (pUmPacket->skbuff) {
 | |
| 			QQ_PushTail (&pDevice->RxPacketFreeQ.Container,
 | |
| 				     pPacket);
 | |
| 			queue_rx = 1;
 | |
| 			continue;
 | |
| 		}
 | |
| 		if ((skb = bcm570xPktAlloc (pUmDevice->index,
 | |
| 					    pPacket->u.Rx.RxBufferSize + 2)) ==
 | |
| 		    0) {
 | |
| 			QQ_PushHead (&pUmDevice->rx_out_of_buf_q.Container,
 | |
| 				     pPacket);
 | |
| 			printf ("NOTICE: Out of RX memory.\n");
 | |
| 			ret = 1;
 | |
| 			break;
 | |
| 		}
 | |
| 
 | |
| 		pUmPacket->skbuff = skb;
 | |
| 		QQ_PushTail (&pDevice->RxPacketFreeQ.Container, pPacket);
 | |
| 		queue_rx = 1;
 | |
| 	}
 | |
| 
 | |
| 	if (queue_rx) {
 | |
| 		LM_QueueRxPackets (pDevice);
 | |
| 	}
 | |
| 
 | |
| 	return ret;
 | |
| }
 | |
| 
 | |
| /*
 | |
|  * Probe, Map, and Init 570x device.
 | |
|  */
 | |
| int eth_init (bd_t * bis)
 | |
| {
 | |
| 	int i, rv, devFound = FALSE;
 | |
| 	pci_dev_t devbusfn;
 | |
| 	unsigned short status;
 | |
| 
 | |
| 	/* Find PCI device, if it exists, configure ...  */
 | |
| 	for (i = 0; i < n570xDevices; i++) {
 | |
| 		devbusfn = pci_find_device (bcm570xDevices[i].vendor_id,
 | |
| 					    bcm570xDevices[i].device_id, 0);
 | |
| 		if (devbusfn == -1) {
 | |
| 			continue;	/* No device of that vendor/device ID */
 | |
| 		} else {
 | |
| 
 | |
| 			/* Set ILINE */
 | |
| 			pci_write_config_byte (devbusfn,
 | |
| 					       PCI_INTERRUPT_LINE,
 | |
| 					       BCM570X_ILINE);
 | |
| 
 | |
| 			/*
 | |
| 			 * 0x10 - 0x14 define one 64-bit MBAR.
 | |
| 			 * 0x14 is the higher-order address bits of the BAR.
 | |
| 			 */
 | |
| 			pci_write_config_dword (devbusfn,
 | |
| 						PCI_BASE_ADDRESS_1, 0);
 | |
| 
 | |
| 			ioBase = BCM570X_MBAR;
 | |
| 
 | |
| 			pci_write_config_dword (devbusfn,
 | |
| 						PCI_BASE_ADDRESS_0, ioBase);
 | |
| 
 | |
| 			/*
 | |
| 			 * Enable PCI memory, IO, and Master -- don't
 | |
| 			 * reset any status bits in doing so.
 | |
| 			 */
 | |
| 			pci_read_config_word (devbusfn, PCI_COMMAND, &status);
 | |
| 
 | |
| 			status |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
 | |
| 
 | |
| 			pci_write_config_word (devbusfn, PCI_COMMAND, status);
 | |
| 
 | |
| 			printf
 | |
| 			    ("\n%s: bus %d, device %d, function %d: MBAR=0x%x\n",
 | |
| 			     board_info[bcm570xDevices[i].board_id].name,
 | |
| 			     PCI_BUS (devbusfn), PCI_DEV (devbusfn),
 | |
| 			     PCI_FUNC (devbusfn), ioBase);
 | |
| 
 | |
| 			/* Allocate once, but always clear on init */
 | |
| 			if (!pDevice) {
 | |
| 				pDevice = malloc (sizeof (UM_DEVICE_BLOCK));
 | |
| 				pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 				memset (pDevice, 0x0, sizeof (UM_DEVICE_BLOCK));
 | |
| 			}
 | |
| 
 | |
| 			/* Configure pci dev structure */
 | |
| 			pUmDevice->pdev = devbusfn;
 | |
| 			pUmDevice->index = 0;
 | |
| 			pUmDevice->tx_pkt = 0;
 | |
| 			pUmDevice->rx_pkt = 0;
 | |
| 			devFound = TRUE;
 | |
| 			break;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	if (!devFound) {
 | |
| 		printf
 | |
| 		    ("eth_init: FAILURE: no BCM570x Ethernet devices found.\n");
 | |
| 		return -1;
 | |
| 	}
 | |
| 
 | |
| 	/* Setup defaults for chip */
 | |
| 	pDevice->TaskToOffload = LM_TASK_OFFLOAD_NONE;
 | |
| 
 | |
| 	if (pDevice->ChipRevId == T3_CHIP_ID_5700_B0) {
 | |
| 		pDevice->TaskToOffload = LM_TASK_OFFLOAD_NONE;
 | |
| 	} else {
 | |
| 
 | |
| 		if (rx_checksum[i]) {
 | |
| 			pDevice->TaskToOffload |=
 | |
| 			    LM_TASK_OFFLOAD_RX_TCP_CHECKSUM |
 | |
| 			    LM_TASK_OFFLOAD_RX_UDP_CHECKSUM;
 | |
| 		}
 | |
| 
 | |
| 		if (tx_checksum[i]) {
 | |
| 			pDevice->TaskToOffload |=
 | |
| 			    LM_TASK_OFFLOAD_TX_TCP_CHECKSUM |
 | |
| 			    LM_TASK_OFFLOAD_TX_UDP_CHECKSUM;
 | |
| 			pDevice->NoTxPseudoHdrChksum = TRUE;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	/* Set Device PCI Memory base address */
 | |
| 	pDevice->pMappedMemBase = (PLM_UINT8) ioBase;
 | |
| 
 | |
| 	/* Pull down adapter info */
 | |
| 	if ((rv = LM_GetAdapterInfo (pDevice)) != LM_STATUS_SUCCESS) {
 | |
| 		printf ("bcm570xEnd: LM_GetAdapterInfo failed: rv=%d!\n", rv);
 | |
| 		return -2;
 | |
| 	}
 | |
| 
 | |
| 	/* Lock not needed */
 | |
| 	pUmDevice->do_global_lock = 0;
 | |
| 
 | |
| 	if (T3_ASIC_REV (pUmDevice->lm_dev.ChipRevId) == T3_ASIC_REV_5700) {
 | |
| 		/* The 5700 chip works best without interleaved register */
 | |
| 		/* accesses on certain machines. */
 | |
| 		pUmDevice->do_global_lock = 1;
 | |
| 	}
 | |
| 
 | |
| 	/* Setup timer delays */
 | |
| 	if (T3_ASIC_REV (pDevice->ChipRevId) == T3_ASIC_REV_5701) {
 | |
| 		pDevice->UseTaggedStatus = TRUE;
 | |
| 		pUmDevice->timer_interval = CONFIG_SYS_HZ;
 | |
| 	} else {
 | |
| 		pUmDevice->timer_interval = CONFIG_SYS_HZ / 50;
 | |
| 	}
 | |
| 
 | |
| 	/* Grab name .... */
 | |
| 	pUmDevice->name =
 | |
| 	    (char *)malloc (strlen (board_info[bcm570xDevices[i].board_id].name)
 | |
| 			    + 1);
 | |
| 	strcpy (pUmDevice->name, board_info[bcm570xDevices[i].board_id].name);
 | |
| 
 | |
| 	eth_getenv_enetaddr("ethaddr", pDevice->NodeAddress);
 | |
| 	LM_SetMacAddress (pDevice);
 | |
| 	/* Init queues  .. */
 | |
| 	QQ_InitQueue (&pUmDevice->rx_out_of_buf_q.Container,
 | |
| 		      MAX_RX_PACKET_DESC_COUNT);
 | |
| 	pUmDevice->rx_last_cnt = pUmDevice->tx_last_cnt = 0;
 | |
| 
 | |
| 	/* delay for 4 seconds */
 | |
| 	pUmDevice->delayed_link_ind = (4 * CONFIG_SYS_HZ) / pUmDevice->timer_interval;
 | |
| 
 | |
| 	pUmDevice->adaptive_expiry = CONFIG_SYS_HZ / pUmDevice->timer_interval;
 | |
| 
 | |
| 	/* Sometimes we get spurious ints. after reset when link is down. */
 | |
| 	/* This field tells the isr to service the int. even if there is */
 | |
| 	/* no status block update. */
 | |
| 	pUmDevice->adapter_just_inited =
 | |
| 	    (3 * CONFIG_SYS_HZ) / pUmDevice->timer_interval;
 | |
| 
 | |
| 	/* Initialize 570x */
 | |
| 	if (LM_InitializeAdapter (pDevice) != LM_STATUS_SUCCESS) {
 | |
| 		printf ("ERROR: Adapter initialization failed.\n");
 | |
| 		return ERROR;
 | |
| 	}
 | |
| 
 | |
| 	/* Enable chip ISR */
 | |
| 	LM_EnableInterrupt (pDevice);
 | |
| 
 | |
| 	/* Clear MC table */
 | |
| 	LM_MulticastClear (pDevice);
 | |
| 
 | |
| 	/* Enable Multicast */
 | |
| 	LM_SetReceiveMask (pDevice,
 | |
| 			   pDevice->ReceiveMask | LM_ACCEPT_ALL_MULTICAST);
 | |
| 
 | |
| 	pUmDevice->opened = 1;
 | |
| 	pUmDevice->tx_full = 0;
 | |
| 	pUmDevice->tx_pkt = 0;
 | |
| 	pUmDevice->rx_pkt = 0;
 | |
| 	printf ("eth%d: %s @0x%lx,",
 | |
| 		pDevice->index, pUmDevice->name, (unsigned long)ioBase);
 | |
| 	printf ("node addr ");
 | |
| 	for (i = 0; i < 6; i++) {
 | |
| 		printf ("%2.2x", pDevice->NodeAddress[i]);
 | |
| 	}
 | |
| 	printf ("\n");
 | |
| 
 | |
| 	printf ("eth%d: ", pDevice->index);
 | |
| 	printf ("%s with ", chip_rev[bcm570xDevices[i].board_id].name);
 | |
| 
 | |
| 	if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5400_PHY_ID)
 | |
| 		printf ("Broadcom BCM5400 Copper ");
 | |
| 	else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5401_PHY_ID)
 | |
| 		printf ("Broadcom BCM5401 Copper ");
 | |
| 	else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5411_PHY_ID)
 | |
| 		printf ("Broadcom BCM5411 Copper ");
 | |
| 	else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5701_PHY_ID)
 | |
| 		printf ("Broadcom BCM5701 Integrated Copper ");
 | |
| 	else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM5703_PHY_ID)
 | |
| 		printf ("Broadcom BCM5703 Integrated Copper ");
 | |
| 	else if ((pDevice->PhyId & PHY_ID_MASK) == PHY_BCM8002_PHY_ID)
 | |
| 		printf ("Broadcom BCM8002 SerDes ");
 | |
| 	else if (pDevice->EnableTbi)
 | |
| 		printf ("Agilent HDMP-1636 SerDes ");
 | |
| 	else
 | |
| 		printf ("Unknown ");
 | |
| 	printf ("transceiver found\n");
 | |
| 
 | |
| 	printf ("eth%d: %s, MTU: %d,",
 | |
| 		pDevice->index, pDevice->BusSpeedStr, 1500);
 | |
| 
 | |
| 	if ((pDevice->ChipRevId != T3_CHIP_ID_5700_B0) && rx_checksum[i])
 | |
| 		printf ("Rx Checksum ON\n");
 | |
| 	else
 | |
| 		printf ("Rx Checksum OFF\n");
 | |
| 	initialized++;
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| /* Ethernet Interrupt service routine */
 | |
| void eth_isr (void)
 | |
| {
 | |
| 	LM_UINT32 oldtag, newtag;
 | |
| 	int i;
 | |
| 
 | |
| 	pUmDevice->interrupt = 1;
 | |
| 
 | |
| 	if (pDevice->UseTaggedStatus) {
 | |
| 		if ((pDevice->pStatusBlkVirt->Status & STATUS_BLOCK_UPDATED) ||
 | |
| 		    pUmDevice->adapter_just_inited) {
 | |
| 			MB_REG_WR (pDevice, Mailbox.Interrupt[0].Low, 1);
 | |
| 			oldtag = pDevice->pStatusBlkVirt->StatusTag;
 | |
| 
 | |
| 			for (i = 0;; i++) {
 | |
| 				pDevice->pStatusBlkVirt->Status &=
 | |
| 				    ~STATUS_BLOCK_UPDATED;
 | |
| 				LM_ServiceInterrupts (pDevice);
 | |
| 				newtag = pDevice->pStatusBlkVirt->StatusTag;
 | |
| 				if ((newtag == oldtag) || (i > 50)) {
 | |
| 					MB_REG_WR (pDevice,
 | |
| 						   Mailbox.Interrupt[0].Low,
 | |
| 						   newtag << 24);
 | |
| 					if (pDevice->UndiFix) {
 | |
| 						REG_WR (pDevice, Grc.LocalCtrl,
 | |
| 							pDevice->
 | |
| 							GrcLocalCtrl | 0x2);
 | |
| 					}
 | |
| 					break;
 | |
| 				}
 | |
| 				oldtag = newtag;
 | |
| 			}
 | |
| 		}
 | |
| 	} else {
 | |
| 		while (pDevice->pStatusBlkVirt->Status & STATUS_BLOCK_UPDATED) {
 | |
| 			unsigned int dummy;
 | |
| 
 | |
| 			pDevice->pMemView->Mailbox.Interrupt[0].Low = 1;
 | |
| 			pDevice->pStatusBlkVirt->Status &=
 | |
| 			    ~STATUS_BLOCK_UPDATED;
 | |
| 			LM_ServiceInterrupts (pDevice);
 | |
| 			pDevice->pMemView->Mailbox.Interrupt[0].Low = 0;
 | |
| 			dummy = pDevice->pMemView->Mailbox.Interrupt[0].Low;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	/* Allocate new RX buffers */
 | |
| 	if (QQ_GetEntryCnt (&pUmDevice->rx_out_of_buf_q.Container)) {
 | |
| 		bcm570xReplenishRxBuffers (pUmDevice);
 | |
| 	}
 | |
| 
 | |
| 	/* Queue packets */
 | |
| 	if (QQ_GetEntryCnt (&pDevice->RxPacketFreeQ.Container)) {
 | |
| 		LM_QueueRxPackets (pDevice);
 | |
| 	}
 | |
| 
 | |
| 	if (pUmDevice->tx_queued) {
 | |
| 		pUmDevice->tx_queued = 0;
 | |
| 	}
 | |
| 
 | |
| 	if (pUmDevice->tx_full) {
 | |
| 		if (pDevice->LinkStatus != LM_STATUS_LINK_DOWN) {
 | |
| 			printf
 | |
| 			    ("NOTICE: tx was previously blocked, restarting MUX\n");
 | |
| 			pUmDevice->tx_full = 0;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	pUmDevice->interrupt = 0;
 | |
| 
 | |
| }
 | |
| 
 | |
| int eth_send (volatile void *packet, int length)
 | |
| {
 | |
| 	int status = 0;
 | |
| #if ET_DEBUG
 | |
| 	unsigned char *ptr = (unsigned char *)packet;
 | |
| #endif
 | |
| 	PLM_PACKET pPacket;
 | |
| 	PUM_PACKET pUmPacket;
 | |
| 
 | |
| 	/* Link down, return */
 | |
| 	while (pDevice->LinkStatus == LM_STATUS_LINK_DOWN) {
 | |
| #if 0
 | |
| 		printf ("eth%d: link down - check cable or link partner.\n",
 | |
| 			pUmDevice->index);
 | |
| #endif
 | |
| 		eth_isr ();
 | |
| 
 | |
| 		/* Wait to see link for one-half a second before sending ... */
 | |
| 		udelay (1500000);
 | |
| 
 | |
| 	}
 | |
| 
 | |
| 	/* Clear sent flag */
 | |
| 	pUmDevice->tx_pkt = 0;
 | |
| 
 | |
| 	/* Previously blocked */
 | |
| 	if (pUmDevice->tx_full) {
 | |
| 		printf ("eth%d: tx blocked.\n", pUmDevice->index);
 | |
| 		return 0;
 | |
| 	}
 | |
| 
 | |
| 	pPacket = (PLM_PACKET)
 | |
| 	    QQ_PopHead (&pDevice->TxPacketFreeQ.Container);
 | |
| 
 | |
| 	if (pPacket == 0) {
 | |
| 		pUmDevice->tx_full = 1;
 | |
| 		printf ("bcm570xEndSend: TX full!\n");
 | |
| 		return 0;
 | |
| 	}
 | |
| 
 | |
| 	if (pDevice->SendBdLeft.counter == 0) {
 | |
| 		pUmDevice->tx_full = 1;
 | |
| 		printf ("bcm570xEndSend: no more TX descriptors!\n");
 | |
| 		QQ_PushHead (&pDevice->TxPacketFreeQ.Container, pPacket);
 | |
| 		return 0;
 | |
| 	}
 | |
| 
 | |
| 	if (length <= 0) {
 | |
| 		printf ("eth: bad packet size: %d\n", length);
 | |
| 		goto out;
 | |
| 	}
 | |
| 
 | |
| 	/* Get packet buffers and fragment list */
 | |
| 	pUmPacket = (PUM_PACKET) pPacket;
 | |
| 	/* Single DMA Descriptor transmit.
 | |
| 	 * Fragments may be provided, but one DMA descriptor max is
 | |
| 	 * used to send the packet.
 | |
| 	 */
 | |
| 	if (MM_CoalesceTxBuffer (pDevice, pPacket) != LM_STATUS_SUCCESS) {
 | |
| 		if (pUmPacket->skbuff == NULL) {
 | |
| 			/* Packet was discarded */
 | |
| 			printf ("TX: failed (1)\n");
 | |
| 			status = 1;
 | |
| 		} else {
 | |
| 			printf ("TX: failed (2)\n");
 | |
| 			status = 2;
 | |
| 		}
 | |
| 		QQ_PushHead (&pDevice->TxPacketFreeQ.Container, pPacket);
 | |
| 		return status;
 | |
| 	}
 | |
| 
 | |
| 	/* Copy packet to DMA buffer */
 | |
| 	memset (pUmPacket->skbuff, 0x0, MAX_PACKET_SIZE);
 | |
| 	memcpy ((void *)pUmPacket->skbuff, (void *)packet, length);
 | |
| 	pPacket->PacketSize = length;
 | |
| 	pPacket->Flags |= SND_BD_FLAG_END | SND_BD_FLAG_COAL_NOW;
 | |
| 	pPacket->u.Tx.FragCount = 1;
 | |
| 	/* We've already provided a frame ready for transmission */
 | |
| 	pPacket->Flags &= ~SND_BD_FLAG_TCP_UDP_CKSUM;
 | |
| 
 | |
| 	if (LM_SendPacket (pDevice, pPacket) == LM_STATUS_FAILURE) {
 | |
| 		/*
 | |
| 		 *  A lower level send failure will push the packet descriptor back
 | |
| 		 *  in the free queue, so just deal with the VxWorks clusters.
 | |
| 		 */
 | |
| 		if (pUmPacket->skbuff == NULL) {
 | |
| 			printf ("TX failed (1)!\n");
 | |
| 			/* Packet was discarded */
 | |
| 			status = 3;
 | |
| 		} else {
 | |
| 			/* A resource problem ... */
 | |
| 			printf ("TX failed (2)!\n");
 | |
| 			status = 4;
 | |
| 		}
 | |
| 
 | |
| 		if (QQ_GetEntryCnt (&pDevice->TxPacketFreeQ.Container) == 0) {
 | |
| 			printf ("TX: emptyQ!\n");
 | |
| 			pUmDevice->tx_full = 1;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	while (pUmDevice->tx_pkt == 0) {
 | |
| 		/* Service TX */
 | |
| 		eth_isr ();
 | |
| 	}
 | |
| #if ET_DEBUG
 | |
| 	printf ("eth_send: 0x%x, %d bytes\n"
 | |
| 		"[%x %x %x %x %x %x %x %x %x %x %x %x %x %x %x %x] ...\n",
 | |
| 		(int)pPacket, length,
 | |
| 		ptr[0], ptr[1], ptr[2], ptr[3], ptr[4], ptr[5],
 | |
| 		ptr[6], ptr[7], ptr[8], ptr[9], ptr[10], ptr[11], ptr[12],
 | |
| 		ptr[13], ptr[14], ptr[15]);
 | |
| #endif
 | |
| 	pUmDevice->tx_pkt = 0;
 | |
| 	QQ_PushHead (&pDevice->TxPacketFreeQ.Container, pPacket);
 | |
| 
 | |
| 	/* Done with send */
 | |
|       out:
 | |
| 	return status;
 | |
| }
 | |
| 
 | |
| /* Ethernet receive */
 | |
| int eth_rx (void)
 | |
| {
 | |
| 	PLM_PACKET pPacket = NULL;
 | |
| 	PUM_PACKET pUmPacket = NULL;
 | |
| 	void *skb;
 | |
| 	int size = 0;
 | |
| 
 | |
| 	while (TRUE) {
 | |
| 
 | |
| 	      bcm570x_service_isr:
 | |
| 		/* Pull down packet if it is there */
 | |
| 		eth_isr ();
 | |
| 
 | |
| 		/* Indicate RX packets called */
 | |
| 		if (pUmDevice->rx_pkt) {
 | |
| 			/* printf("eth_rx: got a packet...\n"); */
 | |
| 			pUmDevice->rx_pkt = 0;
 | |
| 		} else {
 | |
| 			/* printf("eth_rx: waiting for packet...\n"); */
 | |
| 			goto bcm570x_service_isr;
 | |
| 		}
 | |
| 
 | |
| 		pPacket = (PLM_PACKET)
 | |
| 		    QQ_PopHead (&pDevice->RxPacketReceivedQ.Container);
 | |
| 
 | |
| 		if (pPacket == 0) {
 | |
| 			printf ("eth_rx: empty packet!\n");
 | |
| 			goto bcm570x_service_isr;
 | |
| 		}
 | |
| 
 | |
| 		pUmPacket = (PUM_PACKET) pPacket;
 | |
| #if ET_DEBUG
 | |
| 		printf ("eth_rx: packet @0x%x\n", (int)pPacket);
 | |
| #endif
 | |
| 		/* If the packet generated an error, reuse buffer */
 | |
| 		if ((pPacket->PacketStatus != LM_STATUS_SUCCESS) ||
 | |
| 		    ((size = pPacket->PacketSize) > pDevice->RxMtu)) {
 | |
| 
 | |
| 			/* reuse skb */
 | |
| 			QQ_PushTail (&pDevice->RxPacketFreeQ.Container,
 | |
| 				     pPacket);
 | |
| 			printf ("eth_rx: error in packet dma!\n");
 | |
| 			goto bcm570x_service_isr;
 | |
| 		}
 | |
| 
 | |
| 		/* Set size and address */
 | |
| 		skb = pUmPacket->skbuff;
 | |
| 		size = pPacket->PacketSize;
 | |
| 
 | |
| 		/* Pass the packet up to the protocol
 | |
| 		 * layers.
 | |
| 		 */
 | |
| 		NetReceive (skb, size);
 | |
| 
 | |
| 		/* Free packet buffer */
 | |
| 		bcm570xPktFree (pUmDevice->index, skb);
 | |
| 		pUmPacket->skbuff = NULL;
 | |
| 
 | |
| 		/* Reuse SKB */
 | |
| 		QQ_PushTail (&pDevice->RxPacketFreeQ.Container, pPacket);
 | |
| 
 | |
| 		return 0;	/* Got a packet, bail ... */
 | |
| 	}
 | |
| 	return size;
 | |
| }
 | |
| 
 | |
| /* Shut down device */
 | |
| void eth_halt (void)
 | |
| {
 | |
| 	int i;
 | |
| 	if (initialized)
 | |
| 		if (pDevice && pUmDevice && pUmDevice->opened) {
 | |
| 			printf ("\neth%d:%s,", pUmDevice->index,
 | |
| 				pUmDevice->name);
 | |
| 			printf ("HALT,");
 | |
| 			/* stop device */
 | |
| 			LM_Halt (pDevice);
 | |
| 			printf ("POWER DOWN,");
 | |
| 			LM_SetPowerState (pDevice, LM_POWER_STATE_D3);
 | |
| 
 | |
| 			/* Free the memory allocated by the device in tigon3 */
 | |
| 			for (i = 0; i < pUmDevice->mem_list_num; i++) {
 | |
| 				if (pUmDevice->mem_list[i]) {
 | |
| 					/* sanity check */
 | |
| 					if (pUmDevice->dma_list[i]) {	/* cache-safe memory */
 | |
| 						free (pUmDevice->mem_list[i]);
 | |
| 					} else {
 | |
| 						free (pUmDevice->mem_list[i]);	/* normal memory   */
 | |
| 					}
 | |
| 				}
 | |
| 			}
 | |
| 			pUmDevice->opened = 0;
 | |
| 			free (pDevice);
 | |
| 			pDevice = NULL;
 | |
| 			pUmDevice = NULL;
 | |
| 			initialized = 0;
 | |
| 			printf ("done - offline.\n");
 | |
| 		}
 | |
| }
 | |
| 
 | |
| /*
 | |
|  *
 | |
|  * Middle Module: Interface between the HW driver (tigon3 modules) and
 | |
|  * the native (SENS) driver.  These routines implement the system
 | |
|  * interface for tigon3 on VxWorks.
 | |
|  */
 | |
| 
 | |
| /* Middle module dependency - size of a packet descriptor */
 | |
| int MM_Packet_Desc_Size = sizeof (UM_PACKET);
 | |
| 
 | |
| LM_STATUS
 | |
| MM_ReadConfig32 (PLM_DEVICE_BLOCK pDevice,
 | |
| 		 LM_UINT32 Offset, LM_UINT32 * pValue32)
 | |
| {
 | |
| 	UM_DEVICE_BLOCK *pUmDevice;
 | |
| 	pUmDevice = (UM_DEVICE_BLOCK *) pDevice;
 | |
| 	pci_read_config_dword (pUmDevice->pdev, Offset, (u32 *) pValue32);
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS
 | |
| MM_WriteConfig32 (PLM_DEVICE_BLOCK pDevice, LM_UINT32 Offset, LM_UINT32 Value32)
 | |
| {
 | |
| 	UM_DEVICE_BLOCK *pUmDevice;
 | |
| 	pUmDevice = (UM_DEVICE_BLOCK *) pDevice;
 | |
| 	pci_write_config_dword (pUmDevice->pdev, Offset, Value32);
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS
 | |
| MM_ReadConfig16 (PLM_DEVICE_BLOCK pDevice,
 | |
| 		 LM_UINT32 Offset, LM_UINT16 * pValue16)
 | |
| {
 | |
| 	UM_DEVICE_BLOCK *pUmDevice;
 | |
| 	pUmDevice = (UM_DEVICE_BLOCK *) pDevice;
 | |
| 	pci_read_config_word (pUmDevice->pdev, Offset, (u16 *) pValue16);
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS
 | |
| MM_WriteConfig16 (PLM_DEVICE_BLOCK pDevice, LM_UINT32 Offset, LM_UINT16 Value16)
 | |
| {
 | |
| 	UM_DEVICE_BLOCK *pUmDevice;
 | |
| 	pUmDevice = (UM_DEVICE_BLOCK *) pDevice;
 | |
| 	pci_write_config_word (pUmDevice->pdev, Offset, Value16);
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS
 | |
| MM_AllocateSharedMemory (PLM_DEVICE_BLOCK pDevice, LM_UINT32 BlockSize,
 | |
| 			 PLM_VOID * pMemoryBlockVirt,
 | |
| 			 PLM_PHYSICAL_ADDRESS pMemoryBlockPhy, LM_BOOL Cached)
 | |
| {
 | |
| 	PLM_VOID pvirt;
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	dma_addr_t mapping;
 | |
| 
 | |
| 	pvirt = malloc (BlockSize);
 | |
| 	mapping = (dma_addr_t) (pvirt);
 | |
| 	if (!pvirt)
 | |
| 		return LM_STATUS_FAILURE;
 | |
| 
 | |
| 	pUmDevice->mem_list[pUmDevice->mem_list_num] = pvirt;
 | |
| 	pUmDevice->dma_list[pUmDevice->mem_list_num] = mapping;
 | |
| 	pUmDevice->mem_size_list[pUmDevice->mem_list_num++] = BlockSize;
 | |
| 	memset (pvirt, 0, BlockSize);
 | |
| 
 | |
| 	*pMemoryBlockVirt = (PLM_VOID) pvirt;
 | |
| 	MM_SetAddr (pMemoryBlockPhy, (dma_addr_t) mapping);
 | |
| 
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS
 | |
| MM_AllocateMemory (PLM_DEVICE_BLOCK pDevice, LM_UINT32 BlockSize,
 | |
| 		   PLM_VOID * pMemoryBlockVirt)
 | |
| {
 | |
| 	PLM_VOID pvirt;
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 
 | |
| 	pvirt = malloc (BlockSize);
 | |
| 
 | |
| 	if (!pvirt)
 | |
| 		return LM_STATUS_FAILURE;
 | |
| 
 | |
| 	pUmDevice->mem_list[pUmDevice->mem_list_num] = pvirt;
 | |
| 	pUmDevice->dma_list[pUmDevice->mem_list_num] = 0;
 | |
| 	pUmDevice->mem_size_list[pUmDevice->mem_list_num++] = BlockSize;
 | |
| 	memset (pvirt, 0, BlockSize);
 | |
| 	*pMemoryBlockVirt = pvirt;
 | |
| 
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_MapMemBase (PLM_DEVICE_BLOCK pDevice)
 | |
| {
 | |
| 	printf ("BCM570x PCI Memory base address @0x%x\n",
 | |
| 		(unsigned int)pDevice->pMappedMemBase);
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_InitializeUmPackets (PLM_DEVICE_BLOCK pDevice)
 | |
| {
 | |
| 	int i;
 | |
| 	void *skb;
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	PUM_PACKET pUmPacket = NULL;
 | |
| 	PLM_PACKET pPacket = NULL;
 | |
| 
 | |
| 	for (i = 0; i < pDevice->RxPacketDescCnt; i++) {
 | |
| 		pPacket = QQ_PopHead (&pDevice->RxPacketFreeQ.Container);
 | |
| 		pUmPacket = (PUM_PACKET) pPacket;
 | |
| 
 | |
| 		if (pPacket == 0) {
 | |
| 			printf ("MM_InitializeUmPackets: Bad RxPacketFreeQ\n");
 | |
| 		}
 | |
| 
 | |
| 		skb = bcm570xPktAlloc (pUmDevice->index,
 | |
| 				       pPacket->u.Rx.RxBufferSize + 2);
 | |
| 
 | |
| 		if (skb == 0) {
 | |
| 			pUmPacket->skbuff = 0;
 | |
| 			QQ_PushTail (&pUmDevice->rx_out_of_buf_q.Container,
 | |
| 				     pPacket);
 | |
| 			printf ("MM_InitializeUmPackets: out of buffer.\n");
 | |
| 			continue;
 | |
| 		}
 | |
| 
 | |
| 		pUmPacket->skbuff = skb;
 | |
| 		QQ_PushTail (&pDevice->RxPacketFreeQ.Container, pPacket);
 | |
| 	}
 | |
| 
 | |
| 	pUmDevice->rx_low_buf_thresh = pDevice->RxPacketDescCnt / 8;
 | |
| 
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_GetConfig (PLM_DEVICE_BLOCK pDevice)
 | |
| {
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	int index = pDevice->index;
 | |
| 
 | |
| 	if (auto_speed[index] == 0)
 | |
| 		pDevice->DisableAutoNeg = TRUE;
 | |
| 	else
 | |
| 		pDevice->DisableAutoNeg = FALSE;
 | |
| 
 | |
| 	if (line_speed[index] == 0) {
 | |
| 		pDevice->RequestedMediaType = LM_REQUESTED_MEDIA_TYPE_AUTO;
 | |
| 		pDevice->DisableAutoNeg = FALSE;
 | |
| 	} else {
 | |
| 		if (line_speed[index] == 1000) {
 | |
| 			if (pDevice->EnableTbi) {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_FIBER_1000MBPS_FULL_DUPLEX;
 | |
| 			} else if (full_duplex[index]) {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_UTP_1000MBPS_FULL_DUPLEX;
 | |
| 			} else {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_UTP_1000MBPS;
 | |
| 			}
 | |
| 			if (!pDevice->EnableTbi)
 | |
| 				pDevice->DisableAutoNeg = FALSE;
 | |
| 		} else if (line_speed[index] == 100) {
 | |
| 			if (full_duplex[index]) {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_UTP_100MBPS_FULL_DUPLEX;
 | |
| 			} else {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_UTP_100MBPS;
 | |
| 			}
 | |
| 		} else if (line_speed[index] == 10) {
 | |
| 			if (full_duplex[index]) {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS_FULL_DUPLEX;
 | |
| 			} else {
 | |
| 				pDevice->RequestedMediaType =
 | |
| 				    LM_REQUESTED_MEDIA_TYPE_UTP_10MBPS;
 | |
| 			}
 | |
| 		} else {
 | |
| 			pDevice->RequestedMediaType =
 | |
| 			    LM_REQUESTED_MEDIA_TYPE_AUTO;
 | |
| 			pDevice->DisableAutoNeg = FALSE;
 | |
| 		}
 | |
| 
 | |
| 	}
 | |
| 	pDevice->FlowControlCap = 0;
 | |
| 	if (rx_flow_control[index] != 0) {
 | |
| 		pDevice->FlowControlCap |= LM_FLOW_CONTROL_RECEIVE_PAUSE;
 | |
| 	}
 | |
| 	if (tx_flow_control[index] != 0) {
 | |
| 		pDevice->FlowControlCap |= LM_FLOW_CONTROL_TRANSMIT_PAUSE;
 | |
| 	}
 | |
| 	if ((auto_flow_control[index] != 0) &&
 | |
| 	    (pDevice->DisableAutoNeg == FALSE)) {
 | |
| 
 | |
| 		pDevice->FlowControlCap |= LM_FLOW_CONTROL_AUTO_PAUSE;
 | |
| 		if ((tx_flow_control[index] == 0) &&
 | |
| 		    (rx_flow_control[index] == 0)) {
 | |
| 			pDevice->FlowControlCap |=
 | |
| 			    LM_FLOW_CONTROL_TRANSMIT_PAUSE |
 | |
| 			    LM_FLOW_CONTROL_RECEIVE_PAUSE;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	/* Default MTU for now */
 | |
| 	pUmDevice->mtu = 1500;
 | |
| 
 | |
| #if T3_JUMBO_RCV_RCB_ENTRY_COUNT
 | |
| 	if (pUmDevice->mtu > 1500) {
 | |
| 		pDevice->RxMtu = pUmDevice->mtu;
 | |
| 		pDevice->RxJumboDescCnt = DEFAULT_JUMBO_RCV_DESC_COUNT;
 | |
| 	} else {
 | |
| 		pDevice->RxJumboDescCnt = 0;
 | |
| 	}
 | |
| 	pDevice->RxJumboDescCnt = rx_jumbo_desc_cnt[index];
 | |
| #else
 | |
| 	pDevice->RxMtu = pUmDevice->mtu;
 | |
| #endif
 | |
| 
 | |
| 	if (T3_ASIC_REV (pDevice->ChipRevId) == T3_ASIC_REV_5701) {
 | |
| 		pDevice->UseTaggedStatus = TRUE;
 | |
| 		pUmDevice->timer_interval = CONFIG_SYS_HZ;
 | |
| 	} else {
 | |
| 		pUmDevice->timer_interval = CONFIG_SYS_HZ / 50;
 | |
| 	}
 | |
| 
 | |
| 	pDevice->TxPacketDescCnt = tx_pkt_desc_cnt[index];
 | |
| 	pDevice->RxStdDescCnt = rx_std_desc_cnt[index];
 | |
| 	/* Note:  adaptive coalescence really isn't adaptive in this driver */
 | |
| 	pUmDevice->rx_adaptive_coalesce = rx_adaptive_coalesce[index];
 | |
| 	if (!pUmDevice->rx_adaptive_coalesce) {
 | |
| 		pDevice->RxCoalescingTicks = rx_coalesce_ticks[index];
 | |
| 		if (pDevice->RxCoalescingTicks > MAX_RX_COALESCING_TICKS)
 | |
| 			pDevice->RxCoalescingTicks = MAX_RX_COALESCING_TICKS;
 | |
| 		pUmDevice->rx_curr_coalesce_ticks = pDevice->RxCoalescingTicks;
 | |
| 
 | |
| 		pDevice->RxMaxCoalescedFrames = rx_max_coalesce_frames[index];
 | |
| 		if (pDevice->RxMaxCoalescedFrames > MAX_RX_MAX_COALESCED_FRAMES)
 | |
| 			pDevice->RxMaxCoalescedFrames =
 | |
| 			    MAX_RX_MAX_COALESCED_FRAMES;
 | |
| 		pUmDevice->rx_curr_coalesce_frames =
 | |
| 		    pDevice->RxMaxCoalescedFrames;
 | |
| 		pDevice->StatsCoalescingTicks = stats_coalesce_ticks[index];
 | |
| 		if (pDevice->StatsCoalescingTicks > MAX_STATS_COALESCING_TICKS)
 | |
| 			pDevice->StatsCoalescingTicks =
 | |
| 			    MAX_STATS_COALESCING_TICKS;
 | |
| 	} else {
 | |
| 		pUmDevice->rx_curr_coalesce_frames =
 | |
| 		    DEFAULT_RX_MAX_COALESCED_FRAMES;
 | |
| 		pUmDevice->rx_curr_coalesce_ticks = DEFAULT_RX_COALESCING_TICKS;
 | |
| 	}
 | |
| 	pDevice->TxCoalescingTicks = tx_coalesce_ticks[index];
 | |
| 	if (pDevice->TxCoalescingTicks > MAX_TX_COALESCING_TICKS)
 | |
| 		pDevice->TxCoalescingTicks = MAX_TX_COALESCING_TICKS;
 | |
| 	pDevice->TxMaxCoalescedFrames = tx_max_coalesce_frames[index];
 | |
| 	if (pDevice->TxMaxCoalescedFrames > MAX_TX_MAX_COALESCED_FRAMES)
 | |
| 		pDevice->TxMaxCoalescedFrames = MAX_TX_MAX_COALESCED_FRAMES;
 | |
| 
 | |
| 	if (enable_wol[index]) {
 | |
| 		pDevice->WakeUpModeCap = LM_WAKE_UP_MODE_MAGIC_PACKET;
 | |
| 		pDevice->WakeUpMode = LM_WAKE_UP_MODE_MAGIC_PACKET;
 | |
| 	}
 | |
| 	pDevice->NicSendBd = TRUE;
 | |
| 
 | |
| 	/* Don't update status blocks during interrupt */
 | |
| 	pDevice->RxCoalescingTicksDuringInt = 0;
 | |
| 	pDevice->TxCoalescingTicksDuringInt = 0;
 | |
| 
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| 
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_StartTxDma (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket)
 | |
| {
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	printf ("Start TX DMA: dev=%d packet @0x%x\n",
 | |
| 		(int)pUmDevice->index, (unsigned int)pPacket);
 | |
| 
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_CompleteTxDma (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket)
 | |
| {
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	printf ("Complete TX DMA: dev=%d packet @0x%x\n",
 | |
| 		(int)pUmDevice->index, (unsigned int)pPacket);
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_IndicateStatus (PLM_DEVICE_BLOCK pDevice, LM_STATUS Status)
 | |
| {
 | |
| 	char buf[128];
 | |
| 	char lcd[4];
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	LM_FLOW_CONTROL flow_control;
 | |
| 
 | |
| 	pUmDevice->delayed_link_ind = 0;
 | |
| 	memset (lcd, 0x0, 4);
 | |
| 
 | |
| 	if (Status == LM_STATUS_LINK_DOWN) {
 | |
| 		sprintf (buf, "eth%d: %s: NIC Link is down\n",
 | |
| 			 pUmDevice->index, pUmDevice->name);
 | |
| 		lcd[0] = 'L';
 | |
| 		lcd[1] = 'N';
 | |
| 		lcd[2] = 'K';
 | |
| 		lcd[3] = '?';
 | |
| 	} else if (Status == LM_STATUS_LINK_ACTIVE) {
 | |
| 		sprintf (buf, "eth%d:%s: ", pUmDevice->index, pUmDevice->name);
 | |
| 
 | |
| 		if (pDevice->LineSpeed == LM_LINE_SPEED_1000MBPS) {
 | |
| 			strcat (buf, "1000 Mbps ");
 | |
| 			lcd[0] = '1';
 | |
| 			lcd[1] = 'G';
 | |
| 			lcd[2] = 'B';
 | |
| 		} else if (pDevice->LineSpeed == LM_LINE_SPEED_100MBPS) {
 | |
| 			strcat (buf, "100 Mbps ");
 | |
| 			lcd[0] = '1';
 | |
| 			lcd[1] = '0';
 | |
| 			lcd[2] = '0';
 | |
| 		} else if (pDevice->LineSpeed == LM_LINE_SPEED_10MBPS) {
 | |
| 			strcat (buf, "10 Mbps ");
 | |
| 			lcd[0] = '1';
 | |
| 			lcd[1] = '0';
 | |
| 			lcd[2] = ' ';
 | |
| 		}
 | |
| 		if (pDevice->DuplexMode == LM_DUPLEX_MODE_FULL) {
 | |
| 			strcat (buf, "full duplex");
 | |
| 			lcd[3] = 'F';
 | |
| 		} else {
 | |
| 			strcat (buf, "half duplex");
 | |
| 			lcd[3] = 'H';
 | |
| 		}
 | |
| 		strcat (buf, " link up");
 | |
| 
 | |
| 		flow_control = pDevice->FlowControl &
 | |
| 		    (LM_FLOW_CONTROL_RECEIVE_PAUSE |
 | |
| 		     LM_FLOW_CONTROL_TRANSMIT_PAUSE);
 | |
| 
 | |
| 		if (flow_control) {
 | |
| 			if (flow_control & LM_FLOW_CONTROL_RECEIVE_PAUSE) {
 | |
| 				strcat (buf, ", receive ");
 | |
| 				if (flow_control &
 | |
| 				    LM_FLOW_CONTROL_TRANSMIT_PAUSE)
 | |
| 					strcat (buf, " & transmit ");
 | |
| 			} else {
 | |
| 				strcat (buf, ", transmit ");
 | |
| 			}
 | |
| 			strcat (buf, "flow control ON");
 | |
| 		} else {
 | |
| 			strcat (buf, ", flow control OFF");
 | |
| 		}
 | |
| 		strcat (buf, "\n");
 | |
| 		printf ("%s", buf);
 | |
| 	}
 | |
| #if 0
 | |
| 	sysLedDsply (lcd[0], lcd[1], lcd[2], lcd[3]);
 | |
| #endif
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_FreeRxBuffer (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket)
 | |
| {
 | |
| 
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	PUM_PACKET pUmPacket;
 | |
| 	void *skb;
 | |
| 
 | |
| 	pUmPacket = (PUM_PACKET) pPacket;
 | |
| 
 | |
| 	if ((skb = pUmPacket->skbuff))
 | |
| 		bcm570xPktFree (pUmDevice->index, skb);
 | |
| 
 | |
| 	pUmPacket->skbuff = 0;
 | |
| 
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| unsigned long MM_AnGetCurrentTime_us (PAN_STATE_INFO pAnInfo)
 | |
| {
 | |
| 	return get_timer (0);
 | |
| }
 | |
| 
 | |
| /*
 | |
|  *   Transform an MBUF chain into a single MBUF.
 | |
|  *   This routine will fail if the amount of data in the
 | |
|  *   chain overflows a transmit buffer.  In that case,
 | |
|  *   the incoming MBUF chain will be freed.  This routine can
 | |
|  *   also fail by not being able to allocate a new MBUF (including
 | |
|  *   cluster and mbuf headers).  In that case the failure is
 | |
|  *   non-fatal.  The incoming cluster chain is not freed, giving
 | |
|  *   the caller the choice of whether to try a retransmit later.
 | |
|  */
 | |
| LM_STATUS MM_CoalesceTxBuffer (PLM_DEVICE_BLOCK pDevice, PLM_PACKET pPacket)
 | |
| {
 | |
| 	PUM_PACKET pUmPacket = (PUM_PACKET) pPacket;
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	void *skbnew;
 | |
| 	int len = 0;
 | |
| 
 | |
| 	if (len == 0)
 | |
| 		return (LM_STATUS_SUCCESS);
 | |
| 
 | |
| 	if (len > MAX_PACKET_SIZE) {
 | |
| 		printf ("eth%d: xmit frame discarded, too big!, size = %d\n",
 | |
| 			pUmDevice->index, len);
 | |
| 		return (LM_STATUS_FAILURE);
 | |
| 	}
 | |
| 
 | |
| 	skbnew = bcm570xPktAlloc (pUmDevice->index, MAX_PACKET_SIZE);
 | |
| 
 | |
| 	if (skbnew == NULL) {
 | |
| 		pUmDevice->tx_full = 1;
 | |
| 		printf ("eth%d: out of transmit buffers", pUmDevice->index);
 | |
| 		return (LM_STATUS_FAILURE);
 | |
| 	}
 | |
| 
 | |
| 	/* New packet values */
 | |
| 	pUmPacket->skbuff = skbnew;
 | |
| 	pUmPacket->lm_packet.u.Tx.FragCount = 1;
 | |
| 
 | |
| 	return (LM_STATUS_SUCCESS);
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_IndicateRxPackets (PLM_DEVICE_BLOCK pDevice)
 | |
| {
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	pUmDevice->rx_pkt = 1;
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| LM_STATUS MM_IndicateTxPackets (PLM_DEVICE_BLOCK pDevice)
 | |
| {
 | |
| 	PUM_DEVICE_BLOCK pUmDevice = (PUM_DEVICE_BLOCK) pDevice;
 | |
| 	PLM_PACKET pPacket;
 | |
| 	PUM_PACKET pUmPacket;
 | |
| 	void *skb;
 | |
| 	while (TRUE) {
 | |
| 
 | |
| 		pPacket = (PLM_PACKET)
 | |
| 		    QQ_PopHead (&pDevice->TxPacketXmittedQ.Container);
 | |
| 
 | |
| 		if (pPacket == 0)
 | |
| 			break;
 | |
| 
 | |
| 		pUmPacket = (PUM_PACKET) pPacket;
 | |
| 		skb = (void *)pUmPacket->skbuff;
 | |
| 
 | |
| 		/*
 | |
| 		 * Free MBLK if we transmitted a fragmented packet or a
 | |
| 		 * non-fragmented packet straight from the VxWorks
 | |
| 		 * buffer pool. If packet was copied to a local transmit
 | |
| 		 * buffer, then there's no MBUF to free, just free
 | |
| 		 * the transmit buffer back to the cluster pool.
 | |
| 		 */
 | |
| 
 | |
| 		if (skb)
 | |
| 			bcm570xPktFree (pUmDevice->index, skb);
 | |
| 
 | |
| 		pUmPacket->skbuff = 0;
 | |
| 		QQ_PushTail (&pDevice->TxPacketFreeQ.Container, pPacket);
 | |
| 		pUmDevice->tx_pkt = 1;
 | |
| 	}
 | |
| 	if (pUmDevice->tx_full) {
 | |
| 		if (QQ_GetEntryCnt (&pDevice->TxPacketFreeQ.Container) >=
 | |
| 		    (QQ_GetSize (&pDevice->TxPacketFreeQ.Container) >> 1))
 | |
| 			pUmDevice->tx_full = 0;
 | |
| 	}
 | |
| 	return LM_STATUS_SUCCESS;
 | |
| }
 | |
| 
 | |
| /*
 | |
|  *  Scan an MBUF chain until we reach fragment number "frag"
 | |
|  *  Return its length and physical address.
 | |
|  */
 | |
| void MM_MapTxDma
 | |
|     (PLM_DEVICE_BLOCK pDevice,
 | |
|      struct _LM_PACKET *pPacket,
 | |
|      T3_64BIT_HOST_ADDR * paddr, LM_UINT32 * len, int frag) {
 | |
| 	PUM_PACKET pUmPacket = (PUM_PACKET) pPacket;
 | |
| 	*len = pPacket->PacketSize;
 | |
| 	MM_SetT3Addr (paddr, (dma_addr_t) pUmPacket->skbuff);
 | |
| }
 | |
| 
 | |
| /*
 | |
|  *  Convert an mbuf address, a CPU local virtual address,
 | |
|  *  to a physical address as seen from a PCI device.  Store the
 | |
|  *  result at paddr.
 | |
|  */
 | |
| void MM_MapRxDma (PLM_DEVICE_BLOCK pDevice,
 | |
| 		  struct _LM_PACKET *pPacket, T3_64BIT_HOST_ADDR * paddr)
 | |
| {
 | |
| 	PUM_PACKET pUmPacket = (PUM_PACKET) pPacket;
 | |
| 	MM_SetT3Addr (paddr, (dma_addr_t) pUmPacket->skbuff);
 | |
| }
 | |
| 
 | |
| void MM_SetAddr (LM_PHYSICAL_ADDRESS * paddr, dma_addr_t addr)
 | |
| {
 | |
| #if (BITS_PER_LONG == 64)
 | |
| 	paddr->High = ((unsigned long)addr) >> 32;
 | |
| 	paddr->Low = ((unsigned long)addr) & 0xffffffff;
 | |
| #else
 | |
| 	paddr->High = 0;
 | |
| 	paddr->Low = (unsigned long)addr;
 | |
| #endif
 | |
| }
 | |
| 
 | |
| void MM_SetT3Addr (T3_64BIT_HOST_ADDR * paddr, dma_addr_t addr)
 | |
| {
 | |
| 	unsigned long baddr = (unsigned long)addr;
 | |
| #if (BITS_PER_LONG == 64)
 | |
| 	set_64bit_addr (paddr, baddr & 0xffffffff, baddr >> 32);
 | |
| #else
 | |
| 	set_64bit_addr (paddr, baddr, 0);
 | |
| #endif
 | |
| }
 | |
| 
 | |
| /*
 | |
|  * This combination of `inline' and `extern' has almost the effect of a
 | |
|  * macro.  The way to use it is to put a function definition in a header
 | |
|  * file with these keywords, and put another copy of the definition
 | |
|  * (lacking `inline' and `extern') in a library file.  The definition in
 | |
|  * the header file will cause most calls to the function to be inlined.
 | |
|  * If any uses of the function remain, they will refer to the single copy
 | |
|  * in the library.
 | |
|  */
 | |
| void atomic_set (atomic_t * entry, int val)
 | |
| {
 | |
| 	entry->counter = val;
 | |
| }
 | |
| 
 | |
| int atomic_read (atomic_t * entry)
 | |
| {
 | |
| 	return entry->counter;
 | |
| }
 | |
| 
 | |
| void atomic_inc (atomic_t * entry)
 | |
| {
 | |
| 	if (entry)
 | |
| 		entry->counter++;
 | |
| }
 | |
| 
 | |
| void atomic_dec (atomic_t * entry)
 | |
| {
 | |
| 	if (entry)
 | |
| 		entry->counter--;
 | |
| }
 | |
| 
 | |
| void atomic_sub (int a, atomic_t * entry)
 | |
| {
 | |
| 	if (entry)
 | |
| 		entry->counter -= a;
 | |
| }
 | |
| 
 | |
| void atomic_add (int a, atomic_t * entry)
 | |
| {
 | |
| 	if (entry)
 | |
| 		entry->counter += a;
 | |
| }
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| void QQ_InitQueue (PQQ_CONTAINER pQueue, unsigned int QueueSize)
 | |
| {
 | |
| 	pQueue->Head = 0;
 | |
| 	pQueue->Tail = 0;
 | |
| 	pQueue->Size = QueueSize + 1;
 | |
| 	atomic_set (&pQueue->EntryCnt, 0);
 | |
| }				/* QQ_InitQueue */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| char QQ_Full (PQQ_CONTAINER pQueue)
 | |
| {
 | |
| 	unsigned int NewHead;
 | |
| 
 | |
| 	NewHead = (pQueue->Head + 1) % pQueue->Size;
 | |
| 
 | |
| 	return (NewHead == pQueue->Tail);
 | |
| }				/* QQ_Full */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| char QQ_Empty (PQQ_CONTAINER pQueue)
 | |
| {
 | |
| 	return (pQueue->Head == pQueue->Tail);
 | |
| }				/* QQ_Empty */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| unsigned int QQ_GetSize (PQQ_CONTAINER pQueue)
 | |
| {
 | |
| 	return pQueue->Size;
 | |
| }				/* QQ_GetSize */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| unsigned int QQ_GetEntryCnt (PQQ_CONTAINER pQueue)
 | |
| {
 | |
| 	return atomic_read (&pQueue->EntryCnt);
 | |
| }				/* QQ_GetEntryCnt */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /*    TRUE entry was added successfully.                                      */
 | |
| /*    FALSE queue is full.                                                    */
 | |
| /******************************************************************************/
 | |
| char QQ_PushHead (PQQ_CONTAINER pQueue, PQQ_ENTRY pEntry)
 | |
| {
 | |
| 	unsigned int Head;
 | |
| 
 | |
| 	Head = (pQueue->Head + 1) % pQueue->Size;
 | |
| 
 | |
| #if !defined(QQ_NO_OVERFLOW_CHECK)
 | |
| 	if (Head == pQueue->Tail) {
 | |
| 		return 0;
 | |
| 	}			/* if */
 | |
| #endif				/* QQ_NO_OVERFLOW_CHECK */
 | |
| 
 | |
| 	pQueue->Array[pQueue->Head] = pEntry;
 | |
| 	wmb ();
 | |
| 	pQueue->Head = Head;
 | |
| 	atomic_inc (&pQueue->EntryCnt);
 | |
| 
 | |
| 	return -1;
 | |
| }				/* QQ_PushHead */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /*    TRUE entry was added successfully.                                      */
 | |
| /*    FALSE queue is full.                                                    */
 | |
| /******************************************************************************/
 | |
| char QQ_PushTail (PQQ_CONTAINER pQueue, PQQ_ENTRY pEntry)
 | |
| {
 | |
| 	unsigned int Tail;
 | |
| 
 | |
| 	Tail = pQueue->Tail;
 | |
| 	if (Tail == 0) {
 | |
| 		Tail = pQueue->Size;
 | |
| 	}			/* if */
 | |
| 	Tail--;
 | |
| 
 | |
| #if !defined(QQ_NO_OVERFLOW_CHECK)
 | |
| 	if (Tail == pQueue->Head) {
 | |
| 		return 0;
 | |
| 	}			/* if */
 | |
| #endif				/* QQ_NO_OVERFLOW_CHECK */
 | |
| 
 | |
| 	pQueue->Array[Tail] = pEntry;
 | |
| 	wmb ();
 | |
| 	pQueue->Tail = Tail;
 | |
| 	atomic_inc (&pQueue->EntryCnt);
 | |
| 
 | |
| 	return -1;
 | |
| }				/* QQ_PushTail */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| PQQ_ENTRY QQ_PopHead (PQQ_CONTAINER pQueue)
 | |
| {
 | |
| 	unsigned int Head;
 | |
| 	PQQ_ENTRY Entry;
 | |
| 
 | |
| 	Head = pQueue->Head;
 | |
| 
 | |
| #if !defined(QQ_NO_UNDERFLOW_CHECK)
 | |
| 	if (Head == pQueue->Tail) {
 | |
| 		return (PQQ_ENTRY) 0;
 | |
| 	}			/* if */
 | |
| #endif				/* QQ_NO_UNDERFLOW_CHECK */
 | |
| 
 | |
| 	if (Head == 0) {
 | |
| 		Head = pQueue->Size;
 | |
| 	}			/* if */
 | |
| 	Head--;
 | |
| 
 | |
| 	Entry = pQueue->Array[Head];
 | |
| 	membar ();
 | |
| 
 | |
| 	pQueue->Head = Head;
 | |
| 	atomic_dec (&pQueue->EntryCnt);
 | |
| 
 | |
| 	return Entry;
 | |
| }				/* QQ_PopHead */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| PQQ_ENTRY QQ_PopTail (PQQ_CONTAINER pQueue)
 | |
| {
 | |
| 	unsigned int Tail;
 | |
| 	PQQ_ENTRY Entry;
 | |
| 
 | |
| 	Tail = pQueue->Tail;
 | |
| 
 | |
| #if !defined(QQ_NO_UNDERFLOW_CHECK)
 | |
| 	if (Tail == pQueue->Head) {
 | |
| 		return (PQQ_ENTRY) 0;
 | |
| 	}			/* if */
 | |
| #endif				/* QQ_NO_UNDERFLOW_CHECK */
 | |
| 
 | |
| 	Entry = pQueue->Array[Tail];
 | |
| 	membar ();
 | |
| 	pQueue->Tail = (Tail + 1) % pQueue->Size;
 | |
| 	atomic_dec (&pQueue->EntryCnt);
 | |
| 
 | |
| 	return Entry;
 | |
| }				/* QQ_PopTail */
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| PQQ_ENTRY QQ_GetHead (PQQ_CONTAINER pQueue, unsigned int Idx)
 | |
| {
 | |
| 	if (Idx >= atomic_read (&pQueue->EntryCnt)) {
 | |
| 		return (PQQ_ENTRY) 0;
 | |
| 	}
 | |
| 
 | |
| 	if (pQueue->Head > Idx) {
 | |
| 		Idx = pQueue->Head - Idx;
 | |
| 	} else {
 | |
| 		Idx = pQueue->Size - (Idx - pQueue->Head);
 | |
| 	}
 | |
| 	Idx--;
 | |
| 
 | |
| 	return pQueue->Array[Idx];
 | |
| }
 | |
| 
 | |
| /******************************************************************************/
 | |
| /* Description:                                                               */
 | |
| /*                                                                            */
 | |
| /* Return:                                                                    */
 | |
| /******************************************************************************/
 | |
| PQQ_ENTRY QQ_GetTail (PQQ_CONTAINER pQueue, unsigned int Idx)
 | |
| {
 | |
| 	if (Idx >= atomic_read (&pQueue->EntryCnt)) {
 | |
| 		return (PQQ_ENTRY) 0;
 | |
| 	}
 | |
| 
 | |
| 	Idx += pQueue->Tail;
 | |
| 	if (Idx >= pQueue->Size) {
 | |
| 		Idx = Idx - pQueue->Size;
 | |
| 	}
 | |
| 
 | |
| 	return pQueue->Array[Idx];
 | |
| }
 |