41a29f284c
Add a command to load SEAMA (Seattle Image), a NAND flash on-flash storage format. This type of flash image is found in some D-Link routers such as DIR-645, DIR-842, DIR-859, DIR-860L, DIR-885L, DIR890L and DCH-M225, as well as in WD and NEC routers on the ath79 (MIPS), Broadcom BCM53xx, and RAMIPS platforms. This U-Boot command will read and decode a SEAMA image from raw NAND flash on any platform. As it is always using big endian format for the data decoding is always necessary on platforms such as ARM. The command is needed to read a SEAMA-encoded boot image on the D-Link DIR-890L router for boot from NAND flash in an upcoming port of U-Boot to the Broadcom Northstar (BCM4709, BCM53xx) architecture. A basic test and documentation is added as well. The test must be run on a target with NAND flash support and at least one resident SEAMA image in flash. Cc: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
||
|---|---|---|
| .. | ||
| SPI | ||
| SPL | ||
| android | ||
| api | ||
| arch | ||
| board | ||
| build | ||
| chromium | ||
| develop | ||
| device-tree-bindings | ||
| imx | ||
| media | ||
| mvebu | ||
| sphinx | ||
| sphinx-static | ||
| uImage.FIT | ||
| usage | ||
| .gitignore | ||
| I2C_Edge_Conditions | ||
| Makefile | ||
| README.Heterogeneous-SoCs | ||
| README.JFFS2_NAND | ||
| README.LED | ||
| README.OFT | ||
| README.POST | ||
| README.SNTP | ||
| README.TPL | ||
| README.VLAN | ||
| README.VSC3316-3308 | ||
| README.arm-caches | ||
| README.arm-relocation | ||
| README.armada-secureboot | ||
| README.asn1 | ||
| README.atmel_mci | ||
| README.atmel_pmecc | ||
| README.autoboot | ||
| README.bcm7xxx | ||
| README.bcmns3 | ||
| README.bitbangMII | ||
| README.bootcount | ||
| README.boston | ||
| README.cfi | ||
| README.commands.itest | ||
| README.commands.spl | ||
| README.console | ||
| README.davinci | ||
| README.davinci.nand_spl | ||
| README.dfutftp | ||
| README.displaying-bmps | ||
| README.dns | ||
| README.enetaddr | ||
| README.esbc_validate | ||
| README.ext4 | ||
| README.falcon | ||
| README.fec_mxc | ||
| README.fsl-ddr | ||
| README.fsl-esdhc | ||
| README.fsl-hwconfig | ||
| README.fsl-trustzone-components | ||
| README.fsl_iim | ||
| README.fuse | ||
| README.generic-board | ||
| README.generic_usb_ohci | ||
| README.gpio | ||
| README.gpt | ||
| README.hwconfig | ||
| README.i2c | ||
| README.iomux | ||
| README.kconfig | ||
| README.kwbimage | ||
| README.link-local | ||
| README.malta | ||
| README.marvell | ||
| README.mediatek | ||
| README.memory-test | ||
| README.mpc83xx.ddrecc | ||
| README.mpc83xxads | ||
| README.mpc85xx | ||
| README.mpc85xx-sd-spi-boot | ||
| README.mpc85xx-spin-table | ||
| README.mpc85xxcds | ||
| README.multi-dtb-fit | ||
| README.mxc_ocotp | ||
| README.nand | ||
| README.odroid | ||
| README.omap-ulpi-viewport | ||
| README.omap3 | ||
| README.pblimage | ||
| README.pcap | ||
| README.power-framework | ||
| README.pxe | ||
| README.ramboot-ppc85xx | ||
| README.rmobile | ||
| README.rockchip | ||
| README.rockusb | ||
| README.s5p4418 | ||
| README.s5pc1xx | ||
| README.sata | ||
| README.sched | ||
| README.scrapyard | ||
| README.serial_multi | ||
| README.sha1 | ||
| README.silent | ||
| README.socfpga | ||
| README.splashprepare | ||
| README.srio-pcie-boot-corenet | ||
| README.standalone | ||
| README.t1040-l2switch | ||
| README.tee | ||
| README.ti-secure | ||
| README.ubi | ||
| README.ubispl | ||
| README.ublimage | ||
| README.udp | ||
| README.unaligned-memory-access.txt | ||
| README.uniphier | ||
| README.update | ||
| README.usb | ||
| README.vf610 | ||
| README.video | ||
| README.watchdog | ||
| README.zfs | ||
| bounces | ||
| conf.py | ||
| dumpimage.1 | ||
| feature-removal-schedule.txt | ||
| git-mailrc | ||
| index.rst | ||
| kwboot.1 | ||
| mkeficapsule.1 | ||
| mkimage.1 | ||
README.zfs
This patch series adds support for ZFS listing and load to u-boot. To Enable zfs ls and load commands, modify the board specific config file with #define CONFIG_CMD_ZFS Steps to test: 1. After applying the patch, zfs specific commands can be seen in the boot loader prompt using UBOOT #help zfsload- load binary file from a ZFS file system zfsls - list files in a directory (default /) 2. To list the files in zfs pool, device or partition, execute zfsls <interface> <dev[:part]> [POOL/@/dir/file] For example: UBOOT #zfsls mmc 0:5 /rpool/@/usr/bin/ 3. To read and load a file from an ZFS formatted partition to RAM, execute zfsload <interface> <dev[:part]> [addr] [filename] [bytes] For example: UBOOT #zfsload mmc 2:2 0x30007fc0 /rpool/@/boot/uImage References : -- ZFS GRUB sources from Solaris GRUB-0.97 -- GRUB Bazaar repository Jorgen Lundman <lundman at lundman.net> 2012.