155 lines
3.8 KiB
C
155 lines
3.8 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Mentor USB OTG Core functionality common for both Host and Device
|
|
* functionality.
|
|
*
|
|
* Copyright (c) 2008 Texas Instruments
|
|
*
|
|
* Author: Thomas Abraham t-abraham@ti.com, Texas Instruments
|
|
*/
|
|
|
|
#include <common.h>
|
|
|
|
#include "musb_core.h"
|
|
struct musb_regs *musbr;
|
|
|
|
/*
|
|
* program the mentor core to start (enable interrupts, dma, etc.)
|
|
*/
|
|
void musb_start(void)
|
|
{
|
|
#if defined(CONFIG_USB_MUSB_HCD)
|
|
u8 devctl;
|
|
u8 busctl;
|
|
#endif
|
|
|
|
/* disable all interrupts */
|
|
writew(0, &musbr->intrtxe);
|
|
writew(0, &musbr->intrrxe);
|
|
writeb(0, &musbr->intrusbe);
|
|
writeb(0, &musbr->testmode);
|
|
|
|
/* put into basic highspeed mode and start session */
|
|
writeb(MUSB_POWER_HSENAB, &musbr->power);
|
|
#if defined(CONFIG_USB_MUSB_HCD)
|
|
/* Program PHY to use EXT VBUS if required */
|
|
if (musb_cfg.extvbus == 1) {
|
|
busctl = musb_read_ulpi_buscontrol(musbr);
|
|
musb_write_ulpi_buscontrol(musbr, busctl | ULPI_USE_EXTVBUS);
|
|
}
|
|
|
|
devctl = readb(&musbr->devctl);
|
|
writeb(devctl | MUSB_DEVCTL_SESSION, &musbr->devctl);
|
|
#endif
|
|
}
|
|
|
|
#ifdef MUSB_NO_DYNAMIC_FIFO
|
|
# define config_fifo(dir, idx, addr)
|
|
#else
|
|
# define config_fifo(dir, idx, addr) \
|
|
do { \
|
|
writeb(idx, &musbr->dir##fifosz); \
|
|
writew(fifoaddr >> 3, &musbr->dir##fifoadd); \
|
|
} while (0)
|
|
#endif
|
|
|
|
/*
|
|
* This function configures the endpoint configuration. The musb hcd or musb
|
|
* device implementation can use this function to configure the endpoints
|
|
* and set the FIFO sizes. Note: The summation of FIFO sizes of all endpoints
|
|
* should not be more than the available FIFO size.
|
|
*
|
|
* epinfo - Pointer to EP configuration table
|
|
* cnt - Number of entries in the EP conf table.
|
|
*/
|
|
void musb_configure_ep(const struct musb_epinfo *epinfo, u8 cnt)
|
|
{
|
|
u16 csr;
|
|
u16 fifoaddr = 64; /* First 64 bytes of FIFO reserved for EP0 */
|
|
u32 fifosize;
|
|
u8 idx;
|
|
|
|
while (cnt--) {
|
|
/* prepare fifosize to write to register */
|
|
fifosize = epinfo->epsize >> 3;
|
|
idx = ffs(fifosize) - 1;
|
|
|
|
writeb(epinfo->epnum, &musbr->index);
|
|
if (epinfo->epdir) {
|
|
/* Configure fifo size and fifo base address */
|
|
config_fifo(tx, idx, fifoaddr);
|
|
|
|
csr = readw(&musbr->txcsr);
|
|
#if defined(CONFIG_USB_MUSB_HCD)
|
|
/* clear the data toggle bit */
|
|
writew(csr | MUSB_TXCSR_CLRDATATOG, &musbr->txcsr);
|
|
#endif
|
|
/* Flush fifo if required */
|
|
if (csr & MUSB_TXCSR_TXPKTRDY)
|
|
writew(csr | MUSB_TXCSR_FLUSHFIFO,
|
|
&musbr->txcsr);
|
|
} else {
|
|
/* Configure fifo size and fifo base address */
|
|
config_fifo(rx, idx, fifoaddr);
|
|
|
|
csr = readw(&musbr->rxcsr);
|
|
#if defined(CONFIG_USB_MUSB_HCD)
|
|
/* clear the data toggle bit */
|
|
writew(csr | MUSB_RXCSR_CLRDATATOG, &musbr->rxcsr);
|
|
#endif
|
|
/* Flush fifo if required */
|
|
if (csr & MUSB_RXCSR_RXPKTRDY)
|
|
writew(csr | MUSB_RXCSR_FLUSHFIFO,
|
|
&musbr->rxcsr);
|
|
}
|
|
fifoaddr += epinfo->epsize;
|
|
epinfo++;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* This function writes data to endpoint fifo
|
|
*
|
|
* ep - endpoint number
|
|
* length - number of bytes to write to FIFO
|
|
* fifo_data - Pointer to data buffer that contains the data to write
|
|
*/
|
|
__attribute__((weak))
|
|
void write_fifo(u8 ep, u32 length, void *fifo_data)
|
|
{
|
|
u8 *data = (u8 *)fifo_data;
|
|
|
|
/* select the endpoint index */
|
|
writeb(ep, &musbr->index);
|
|
|
|
/* write the data to the fifo */
|
|
while (length--)
|
|
writeb(*data++, &musbr->fifox[ep]);
|
|
}
|
|
|
|
/*
|
|
* AM35x supports only 32bit read operations so
|
|
* use seperate read_fifo() function for it.
|
|
*/
|
|
#ifndef CONFIG_USB_AM35X
|
|
/*
|
|
* This function reads data from endpoint fifo
|
|
*
|
|
* ep - endpoint number
|
|
* length - number of bytes to read from FIFO
|
|
* fifo_data - pointer to data buffer into which data is read
|
|
*/
|
|
__attribute__((weak))
|
|
void read_fifo(u8 ep, u32 length, void *fifo_data)
|
|
{
|
|
u8 *data = (u8 *)fifo_data;
|
|
|
|
/* select the endpoint index */
|
|
writeb(ep, &musbr->index);
|
|
|
|
/* read the data to the fifo */
|
|
while (length--)
|
|
*data++ = readb(&musbr->fifox[ep]);
|
|
}
|
|
#endif /* CONFIG_USB_AM35X */
|