209 lines
7.3 KiB
C
209 lines
7.3 KiB
C
/*
|
|
* (C) Copyright 2000-2005
|
|
* Stefan Roese, DENX Software Engineering, sr@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
|
|
#define CONFIG_WALNUT 1 /* ...on a WALNUT board */
|
|
/* ...or on a SYCAMORE board */
|
|
|
|
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
|
|
|
|
/*
|
|
* Include common defines/options for all AMCC eval boards
|
|
*/
|
|
#define CONFIG_HOSTNAME walnut
|
|
#include "amcc-common.h"
|
|
|
|
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
|
|
|
|
/*
|
|
* Default environment variables
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
CONFIG_AMCC_DEF_ENV \
|
|
CONFIG_AMCC_DEF_ENV_POWERPC \
|
|
CONFIG_AMCC_DEF_ENV_PPC_OLD \
|
|
CONFIG_AMCC_DEF_ENV_NOR_UPD \
|
|
"kernel_addr=fff80000\0" \
|
|
"ramdisk_addr=fff80000\0" \
|
|
""
|
|
|
|
#define CONFIG_PHY_ADDR 1 /* PHY address */
|
|
#define CONFIG_HAS_ETH0 1
|
|
|
|
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
|
|
|
|
/*
|
|
* Commands additional to the ones defined in amcc-common.h
|
|
*/
|
|
#define CONFIG_CMD_DATE
|
|
#define CONFIG_CMD_PCI
|
|
#define CONFIG_CMD_SDRAM
|
|
|
|
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
|
|
|
|
/*
|
|
* If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
|
|
* If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
|
|
* Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
|
|
* The Linux BASE_BAUD define should match this configuration.
|
|
* baseBaud = cpuClock/(uartDivisor*16)
|
|
* If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
|
|
* set Linux BASE_BAUD to 403200.
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
|
|
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
|
|
#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
|
|
#define CONFIG_SYS_BASE_BAUD 691200
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* I2C stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
|
|
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCI stuff
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
|
|
#define PCI_HOST_FORCE 1 /* configure as pci host */
|
|
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
|
|
|
|
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
|
|
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
|
|
/* resource configuration */
|
|
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
|
|
|
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
|
|
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
|
|
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
|
|
#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
|
|
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
|
|
#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
|
|
#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
|
|
#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
*/
|
|
#define CONFIG_SYS_FLASH_BASE 0xFFF80000
|
|
|
|
/*
|
|
* Define here the location of the environment variables (FLASH or NVRAM).
|
|
* Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
|
|
* supported for backward compatibility.
|
|
*/
|
|
#if 1
|
|
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
|
|
#else
|
|
#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
|
|
#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
|
|
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
|
|
|
|
#define CONFIG_SYS_FLASH_ADDR0 0x5555
|
|
#define CONFIG_SYS_FLASH_ADDR1 0x2aaa
|
|
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_FLASH
|
|
#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
|
|
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
|
|
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
|
|
#endif /* CONFIG_ENV_IS_IN_FLASH */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* NVRAM organization
|
|
*/
|
|
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */
|
|
#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */
|
|
|
|
#ifdef CONFIG_ENV_IS_IN_NVRAM
|
|
#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
|
|
#define CONFIG_ENV_ADDR \
|
|
(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External Bus Controller (EBC) Setup
|
|
*/
|
|
|
|
/* Memory Bank 0 (Flash Bank 0) initialization */
|
|
#define CONFIG_SYS_EBC_PB0AP 0x9B015480
|
|
#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
#define CONFIG_SYS_EBC_PB1AP 0x02815480
|
|
#define CONFIG_SYS_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
#define CONFIG_SYS_EBC_PB2AP 0x04815A80
|
|
#define CONFIG_SYS_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
#define CONFIG_SYS_EBC_PB3AP 0x01815280
|
|
#define CONFIG_SYS_EBC_PB3CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
#define CONFIG_SYS_EBC_PB7AP 0x01815280
|
|
#define CONFIG_SYS_EBC_PB7CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* External peripheral base address
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000
|
|
#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000
|
|
#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area
|
|
*/
|
|
#define CONFIG_SYS_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */
|
|
|
|
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* inside of SDRAM */
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for Serial Presence Detect EEPROM address
|
|
* (to get SDRAM settings)
|
|
*/
|
|
#define SPD_EEPROM_ADDRESS 0x50
|
|
|
|
#endif /* __CONFIG_H */
|