nrhw20: cleanup board file

board/nm/nrhw20/board.c

@@ -144,6 +144,7 @@ static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
 #endif
 
 
+#define I2C_BD_EEPROM_BUS		(2)
 #define BD_EEPROM_ADDR			(0x50)	  /* CPU BD EEPROM (8kByte) is at 50 (A0) */
 #define BD_ADDRESS			(0x0000)  /* Board descriptor at beginning of EEPROM */
 #define PD_ADDRESS			(0x0200)  /* Product descriptor */
@@ -159,9 +160,8 @@ static int _bd_init(void)
 {
 	int old_bus;
 
-	/* TODO: Use a define for bus number */
 	old_bus = i2c_get_bus_num();
-	i2c_set_bus_num(2);
+	i2c_set_bus_num(I2C_BD_EEPROM_BUS);
 
 	if (bd_get_context(&bdctx[0], BD_EEPROM_ADDR, BD_ADDRESS) != 0) {
 		printf("%s() no valid bd found\n", __func__);
@@ -215,6 +215,7 @@ static void set_indicator(unsigned led, int red, int green)
 
 	if (!red)
 		led_val |= led_red_mask;
+
 	if (!green)
 		led_val |= led_green_mask;
 
@@ -283,9 +284,9 @@ static struct emif_regs ddr3_emif_reg_data = {
 
 #define OSC	(V_OSCK/1000000)
 
-/* TODO: Rename */
-struct dpll_params dpll_ddr_nbhw16= {
-		DDR3_CLOCK_FREQUENCY, OSC-1, 1, -1, -1, -1, -1};
+struct dpll_params dpll_ddr_nrhw20 = {
+	DDR3_CLOCK_FREQUENCY, OSC-1, 1, -1, -1, -1, -1
+};
 
 
 void am33xx_spl_board_init(void)
@@ -317,8 +318,8 @@ void am33xx_spl_board_init(void)
 
 const struct dpll_params *get_dpll_ddr_params(void)
 {
-	dpll_ddr_nbhw16.n = (get_osclk() / 1000000) - 1;
-	return &dpll_ddr_nbhw16;
+	dpll_ddr_nrhw20.n = (get_osclk() / 1000000) - 1;
+	return &dpll_ddr_nrhw20;
 }
 
 void set_uart_mux_conf(void)
@@ -673,15 +674,6 @@ int board_init(void)
 	mdelay(1200);
 	gpio_set_value(NETBIRD_GPIO_PWR_GSM, 0);
 
-#if 0
-	/* TODO: Move to pinmux? Required??? RMII2 not used! */
-	/* There are two functions on the same mux mode for MMC2_DAT7 we want
-	 * to use RMII2_CRS_DV so we need to set SMA2 Register to 1
-	 * See SPRS717J site 49 (10)*/
-	#define SMA2_REGISTER (CTRL_BASE + 0x1320)
-	writel(0x01, SMA2_REGISTER); /* Select RMII2_CRS_DV instead of MMC2_DAT7 */
-#endif
-
 	printf("OSC:   %lu MHz\n", get_osclk()/1000000);
 
 	return 0;
@@ -727,8 +719,7 @@ static void set_devicetree_name(void)
 
 	/* add hardware versions to environment */
 	if (bd_get_devicetree(devicetreename, sizeof(devicetreename)) != 0) {
-		printf("Devicetree name not found, using legacy name\n");
-		/* TODO: Check naming convention */
+		printf("Devicetree name not found, using default name\n");
 		strcpy(devicetreename, "am335x-nrhw20-prod1.dtb");
 	}
 
@@ -739,12 +730,12 @@ static void get_hw_version(void)
 {
 	int hw_ver, hw_rev;
 	char hw_versions[16];
-	char new_env[256];	/* TODO: Check size, have also seen 512 */
+	char new_env[256];	/* current bootargs = 84 bytes */
 
-	/* add hardware versions to environment */
 	bd_get_hw_version(&hw_ver, &hw_rev);
 	printf("HW20:  V%d.%d\n", hw_ver, hw_rev);
 
+	/* add hardware versions to environment */
 	snprintf(hw_versions, sizeof(hw_versions), "CP=%d.%d", hw_ver, hw_rev);
 	snprintf(new_env, sizeof(new_env), "setenv bootargs $bootargs %s", hw_versions);
 	setenv("add_version_bootargs", new_env);
@@ -757,14 +748,21 @@ static void check_fct(void)
 	 * Clear the bootcmd, so that test system can easily connect.
 	 */
 
+	int old_bus;
+
+	old_bus = i2c_get_bus_num();
+	i2c_set_bus_num(I2C_BD_EEPROM_BUS);
+
 	/* If probe fails we are sure no eeprom is connected */
 	if (i2c_probe(0x51) == 0) {
 		printf("Entering fct mode\n");
 		setenv ("bootcmd", "");
 	}
-	/* TODO: needs to test on bus 2 ! */
+
+	i2c_set_bus_num(old_bus);
 }
 
+
 static void set_fdtshieldcmd(const char *fdt_cmd)
 {
 	setenv("fdtshieldcmd", fdt_cmd);
@@ -838,8 +836,9 @@ static void shield_config(void)
 	cmd->init();
 	shieldcmd = cmd->default_shieldcmd;
 
-	/* If a shield configuration set by linux take it without bd check, we asume that Linux knows
-	 * what to do. */
+	/* If a shield configuration is set by Linux, take it without bd check.
+	 * We asume that Linux knows what to do.
+	 */
 	len = read_file("/root/boot/shieldcmd", shieldcmd_linux, MAX_SHIELD_CMD_LEN);
 	if (len > 0) {
 		debug("Shield command found in file, using it\n");